Design of a dynamic stall test rig

Applied Mechanics and Materials

Volumn 215-216, Issue , 2012, Pages 785-795

  Shun, Simon ^a   Ahmed, Noor Alam ^a  

^a UNIVERSITY OF NEW SOUTH WALES   (Australia)

Author keywords

CAD CAM; Cyclical loads; Dynamic stall; Fatigue; Test rig; Wind tunnel

Indexed keywords

AERODYNAMIC PHENOMENA; AMBIENT FLOW; BLADE SPAN; CAD/CAMS; CYCLICAL LOADS; DESIGN CALCULATIONS; DESIGN PROCESS; DYNAMIC STALLS; FORWARD SPEED; LABORATORY ENVIRONMENT; MOMENT COEFFICIENT; OPERATING CONDITION; SHORT TIME FRAMES; STRUCTURAL ISSUES; TEST RIGS; UNDESIRABLE EFFECTS;

AERODYNAMIC STALLING; AIRFOILS; ANGLE OF ATTACK; FATIGUE OF MATERIALS; HELICOPTERS; WIND TUNNELS; WIND TURBINES;

COMPUTER AIDED DESIGN;

EID: 84870556180     PISSN: 16609336     EISSN: 16627482     Source Type: Book Series    
DOI: 10.4028/www.scientific.net/AMM.215-216.785     Document Type: Conference Paper

References (42)

1. Singh, C., Peake, D.J., Kokkalis, A., Khodagolian, V., Coton, F.N. & Galbraith, R.A.M., "Control of Rotorcraft Retreating Blade Stall Using Air-Jet Vortex Generators," Journal of Aircraft, Vol. 43, No. 4, 2006, pp. 1169-1176.
2. Mulleners, K. & Raffel, M., "The onset of dynamic stall revisited," Experiments in Fluids, Vol. 52, No. 3, 2012, pp. 779-793.
3. Leishman, J.G., "Dynamic stall experiments on the NACA 23012 aerofoil," Experiments in Fluids, Vol.9, No. 1-2, 1990, pp. 49-58.
4. De Gregorio, F., Pengel, K. & Kindler, K., "A comprehensive PIV measurement campaign on a fully equipped helicopter model," Experiments in fluids, available online, http://www.springerlink.com/content/g386347588561764/
5. rd International Symposium on Laser Anemometry, edited by Dybs, A. et al, ASME, The Fluids Engineering Division, Vol. 55, pp.175-178.
6. Ahmed, N.A., Elder, R.L., Foster, C.P. & Jones, J.D.C., "Miniature Laser Anemometer for 3D Measurements," Engineering Optics, Vol. 3, No. 2, 1990, pp.191-196.
7. Ahmed, N.A., Elder, R.L., Foster, C.P. & Jones, J.D.C, "Laser Anemometry in Turbomachines," IMechE Proc, Part G, J of Aerospace Engineering, Vol. 205, 1991, pp.1-12.
8. Ahmed, N.A., Elder, R.L., Foster, C.P. & Jones, J.D.C, "Fibre Optic Laser Anemometry for Turbo machinery Applications," Optics and Lasers in Engineering, Vol. 15, No. 2-3, 1992, pp.193-205.
9. Ahmed, N.A. & Elder, R.L., "Flow Behavior in a High Speed Centrifugal Impeller Passage under Design and Off-design Operating Conditions," Fluids and Thermal Engineering, JSME International series B, Vol.43, No.1, 2000, pp. 22-28.
10. Gatto, A., Byrne, K.P., Ahmed, N.A. & Archer, R.D., "Pressure Measurements over a Cylinder in Crossflow using Plastic Tubing," Experiments in Fluids, Vol. 30, Iss. 1, 2001, pp. 43-46.
11. Ahmed, N.A., "Implementation of a momentum integral technique for total drag measurement," International Journal of Mechanical Engineering and Education, Vol.30, No.4, 2002.
12. Pissasale, A., &Ahmed, N.A., "Theoretical calibration of a five hole probe for highly three dimensional flow," International Journal of Measurement Science and Technology, Vol. 13, July, 2002, pp.1100-1107.
13. Pissasale, A., & Ahmed, N.A., "A novel method of extending the calibration range of five hole probe for highly three dimensional flows," Journal of Flow Measurement and Instrumentation, vol. 13, issues 1-2, March-April, 2002, pp 23-30
14. Pissasale, A., & Ahmed, N.A., "Examining the effect of flow reversal on seven-hole probe measurements," AIAA Journal, Vol. 41, No. 12, 2003, pp. 2460-2467.
15. Pissasale, A., & Ahmed, N.A., "Development of a functional relationship between port pressures and flow properties for the calibration and application of multi-hole probes to highly three-dimensional flows," Experiments in Fluids, Vol. 36, No.3, 2004, pp. 422-436.
16. Lien, J. & Ahmed, N.A., "An examination of the suitability of multi-hole pressure probe technique for skin friction measurement in turbulent flow," in press, Journal of Flow Measurement and Instrumentation, Vol. 22, 2011, pp. 153-164
17. Ahmed, N.A., "Detection of Separation bubble using spectral analysis of fluctuating surface pressure," International Review of Aerospace Engineering, Vol.4, No. 4, 2011.
18. Simpson, R.G., Ahmed, N.A. & Archer, R.D., "Improvement of a Wing Performance using Coanda Tip Jets," Journal of Aircraft, Vol. 37, No. 1, 2000, pp.183-184.
19. Ahmed, N.A. & Archer, R.D., "Performance Improvement of a Bi-plane with Endplates," Journal of Aircraft, Vol.38, No.2, 2001, pp. 398-400.
20. Ahmed, N.A. & Archer, R.D., "Post-Stall Behavior of a Wing under Externally Imposed Sound," Journal of Aircraft, Vol. 38, No.5, 2001, pp. 961-963.
21. Simpson, R.G., Ahmed, N.A. & Archer, R.D., "Near Field Study of Vortex Attenuation using Wing Tip Blowing", The Aeronautical Journal, Vol. 102, March, 2002
22. Ahmed, N.A. & Goonaratne, J., "Lift augmentation of a low aspect ratio thick wing at a very low angle of incidence operating in ground effect," Journal of Aircraft, Vol. 39, No.2, 2002,
23. Ahmed, N.A., "An acoustic energy concept for the design of a flow meter," International Journal of Vibration and Acoustics, Vol.8, No.1, 2003, pp. 52-58.
24. Longmuir, M. & Ahmed, N.A., "Commercial Aircraft Exterior Cleaning Optimization," Journal of Aircraft, Vol. 46, No. 1, 2009, pp. 284-290.
25. Wu, C. & Ahmed, N.A., "Numerical Study of Transient Aircraft Cabin Flowfield with Unsteady Air Supply," Journal of Aircraft, Vol. 48, no.6, 2011, pp. 2164-2169.
26. Wu, C. & Ahmed, N.A., "Application of Flow Control Technique for Indoor Ventilation," proceedings, Evolving Energy-IEF International Energy Congress, Sydney; 2012.
27. Matsoukas, G, & Ahmed, N.A., "Experimental Investigation of Employing Asymmetrical Electrodes in Propulsion of Vehicles," proceedings, Evolving Energy-IEF International Energy Congress, Sydney; 2012.
28. Riazi, H. & Ahmed, N.A., "Effect of the ratio of specific heats on a small scale solar Brayton cycle," proceedings, Evolving Energy-IEF International Energy Congress, Sydney; 2012.
29. Yen, J. & Ahmed, N.A., "Improving the Safety and Performance of Small-Scale Vertical Axis Wind Turbine," proceedings, IEF International Energy Congress, Sydney, 2012.
30. Wongpanyathaworn, M., & Ahmed, N.A., "Optimising louver locations to improve indoor thermal comfort based on natural ventilation," proceedings, Evolving Energy-IEF International Energy Congress, Sydney; 2012.
31. Findanis, N. & Ahmed, N.A., "Control and Management of Particulate Emissions using Improved Reverse Pulse-Jet Cleaning Systems," proceedings, Evolving Energy-IEF International Energy Congress, Sydney; 2012.
32. Flynn, T.G., Behfarshad, G. & Ahmed, N.A., "Development of a Wind Tunnel Test Section to Simulate the Effect of Rain on roof ventilation systems and environmental measuring devices," proceedings, Evolving Energy-IEF International Energy Congress, Sydney; 2012.
33. Zheng, Y.Y., Ahmed, N.A. & Zhang, W., "Impact Analysis of Varying Strength Counter-flow Jet Ejection on a Blunt Shaped Body in A Supersonic Flow," in press, Advances and Applications in Fluid Mechanics.
34. Matsoukas, G. & Ahmed, N.A., "Investigation of Ionic Wind as a Means of Generating Propulsive Force," in press, International Review of Aerospace Engineering.
35. Lua, K.B., Lim, T.T. & Yeo, K.S., "Effect of wing-wake interaction on aerodynamic force generation on a 2D flapping wing," Experiments in Fluids, Vol. 51, No. 1, 2011, pp.177-195.
36. Ol, M. V., Bernal, L., Kwon Kang, C. & Shyy, W., "Shallow and deep dynamic stall for flapping low Reynolds number airfoils," Experiments in Fluids, Vol. 46, No. 5, 2009, pp. 883-901.
37. Rival, D., Prangemeier, T. & Tropea, C., "The influence of airfoil kinematics on the formation of leading-edge vortices in bio-inspired flight," Experiments in Fluids, Vol. 46, No. 5, 2009, pp. 823-833.
38. Traub, L.W., Miller, A. & Rediniotis, O., "Effects of Synthetic Jet Actuation on a Ramping NACA 0015 Airfoil," Journal of Aircraft, Vol. 41, No. 5, 2004, pp. 1153-1162.
39. Gerontakos, P. & Lee. T., "Particle image velocimetry investigation of flow over unsteady airfoil with trailing-edge strip," Experiments in Fluids, Vol. 44, No. 4, 2008, pp. 539-556.
40. Fuglsang, P., Antoniou, I., Bak, C. & Madsen, H.A., "Wind Tunnel Test of the RISØ-1Airfoil," Risø-R-999(EN), May 1998, Risø National Laboratory, Roskilde, Denmark.
41. Bak, C., Fuglsang, P., Johansen, J. & Antoniou, I., "Wind Tunnel Tests of the NACA 63-415 and a Modified NACA 63-415 Airfoil, "Risø-R-1193(EN), December 2000, Risø National Laboratory, Roskilde, Denmark.
42. Fuglsang, P., Bak, C., Gaunaa, M. & Antoniou, I., "Wind Tunnel Tests of Risø-B1-18 and Risø-B1-24," Risø-R-1375(EN), January 2003, Risø National Laboratory, Roskilde, Denmark.