Assessment of plastic flows and stocks in Serbia using material flow analysis

Thermal Science

Volumn 14, Issue SUPPL.1, 2010, Pages

  Vujić, Goran V ^a   Jovičić, Nebojša M ^b   Babić, Milun J ^b   Stanisavljević, Nemanja Z ^a   Batinić, Bojan M ^a   Pavlović, Aleksandar R ^c  

^a UNIVERSITY OF NOVI SAD   (Serbia)

^b UNIVERSITY OF KRAGUJEVAC   (Serbia)

^c DOO Jugo Drvo Holding   (Serbia)

Author keywords

Material flow analysis; Plastic; Storage; Waste

Indexed keywords

PLASTIC PRODUCTS;

DIRECT PLASTICS; FILLED PLASTICS; HUMAN HEALTH; LANDFILLING; MATERIALS FLOW ANALYSIS; PLASTIC MATERIAL FLOW; PLASTIC MATERIALS; PRE-TREATMENTS;

LAND FILL;

EID: 84869764879     PISSN: 03549836     EISSN: None     Source Type: Journal    
DOI: 10.2298/TSCI100621031V     Document Type: Article

References (15)

1. Mitelea, I., et al, The High Frequency Welding Aptitude of Thermoplastic Polymers, Materiale Plastice, 46, (2009), 1 pp. 101-107
2. ***, The Compelling Facts About Plastics 2009, An Analysis of European Plastics Production and Recovery for 2008
3. Pichtel, J., Waste Management Practices: Municipal, Hazardous, and Industrial, Taylor & Francis, Boca Raton, Fla., USA, 2005
4. Brunner, P.H., Rechberger, H., Practical Handbook of Material Flow Analysis, Lewis Publishers, New York, USA, 2004
5. Baccini, P., Brunner, P.H., Metabolism of the Anthropo-Sphere, Springer, New York, USA, 1991
6. Vujic, G., et al, Determining Waste Composition and Assessment of the Amount with the Aim of Defining Strategies in the Secondary Raw Materials Resources in the Frame of Sustainable Development of the Republic of Serbia, Project Report for 2009, pp. 69-70, Faculty of Technical Sciences, University of Novi Sad, Novi Sad, Serbia, 2009
7. ***, World Economic Outlook, International Monetary Fund, 2008, p. 264
8. Skovgaard, M. et al, Outlook for Waste and Material Flows Baseline and Alternative Scenarios, ETC/RWM European Topic Center on Recourse and Waste Management working paper 2005/1, Copenhagen, Denmark, 2005
9. ***, Industry of the Republic of Serbia 2008, Statistical Office of the Republic of Serbia (in Serbian), ISSN 0354 - 3641, Belgrade, 2009
10. ***, Statistical Yearbook of Serbia 2009, Statistical Office of the Republic of Serbia (in Serbian), ISSN 0354 - 4206, Belgrade, 2009
11. Bogucka, R., Brunner, P.H., Evaluation of Plastic Flows and Their Management in Austria and Poland: Challenges and Opportunities, Vienna University of Technology, Institute for Water Quality Recourses and Waste Management, Vienna, 2007
12. Patel, M. K., Jochem, E., Radgen, P., Plastic Steams in Germany - an Analysis and Production, Consumption and Waste Generation, Resources, Conservation and Recycling, 24 (1998), 3, pp. 191-215
13. Vujic, G., et al, Identification and Categorization of Wild Landfills on the Territory of the Republic of Serbia, Project Report for 2009 (in Serbian), Faculty of Technical Sciences, University of Novi Sad, Novi Sad, Serbia, 2009
14. Bogucka, R., et.al, Setting Priorities in Plastic Waste Management - Lessons Learned from Material Flow Analysis in Austria and Poland, Polimery, 53 (2008), 1, pp. 55-59
15. Mutha, N. H., Patel M. K., Premnath, V., Plastics Materials flow analysis for India, Resources, Conservation & Recycling, 47, (2006), 3, pp. 222-244