Study on the dynamics of the in-wheel motor system

IEEE Transactions on Vehicular Technology

Volumn 61, Issue 8, 2012, Pages 3510-3518

  Luo, Yutao ^a   Tan, Di ^a  

^a SOUTH CHINA UNIVERSITY OF TECHNOLOGY   (China)

Author keywords

In wheel motor (IWM); motor magnet gap (MMG); road surface roughness (RSR) excitation; rubber bushing; vehicle dynamics

Indexed keywords

ANALYSIS APPROACH; BODY VIBRATION; IN-WHEEL MOTOR; MASS INCREASE; PROPULSION SYSTEM; ROAD SURFACE ROUGHNESS; ROAD SURFACES; RUBBER BUSHING; SUSPENSION DYNAMICS; TIRE DYNAMICS; UNSPRUNG MASS; VEHICLE DYNAMICS; VEHICLE VIBRATIONS; VERTICAL DYNAMICS; VIBRATION ENERGIES;

ALL WHEEL DRIVE VEHICLES; DEFORMATION; DYNAMIC LOADS; MAGNETS; RUBBER; VIBRATIONS (MECHANICAL);

BUSHINGS;

EID: 84867756269     PISSN: 00189545     EISSN: None     Source Type: Journal    
DOI: 10.1109/TVT.2012.2207414     Document Type: Article

References (22)

1. K. Kamiya, J. Okuse, and K. Ooishi, in Development of In-Wheel Motor System for Micro EV: Proc. 18th Int. Electric Vehicle Symp., Berlin, Germany, 2001.
2. F. Tahami, R. Kazemi, and S. Farhanghi, "A novel driver assist stability system for all-wheel-drive electric vehicles," IEEE Trans. Veh. Technol., vol. 52, no. 3, May 2003.
3. E. Esmailzadeh, G. R. Vossoughi, and A. Goodarzi, "Dynamic modeling and analysis of a four motorized wheels electric vehicle," Vehicle Syst. Dyn., vol. 35, no. 3, pp. 163-194, 2001. (Pubitemid 32796724)
4. D. J. Purdy and D. Simner, "A brief investigation into the effect on suspension motions ofhigh unsprung mass," J. Battlefield Technol., vol. 7, no. 1, pp. 15-20, 2004.
5. Siddiqui and O. Mustafa, "Dynamic analysis of a modern urban bus for assessment of ride quality and dynamic wheel loads," Mechanical Ind. Eng., 2000.
6. G. Nagaya, Y. Wakao, and A. Abe, "Development of an in-wheel drive with advanced dynamic-damper mechanism," JSAE Rev., vol. 24, pp.477-481, 2003.
7. J. F. Eastham, M. J. Balchin, T. Betzer, H. C. Lai, and S. Gairt, "Disc motor with reduced unsprung mass for direct EV wheel drive," in Proc. IEEEInt. Symp., 1995.
8. X. C. Liang and N. G. Bao, "Active control of vertical vibration negative influences induced by high unsprung mass of in-wheel motor electric vehicle," Chin. J. Constr. Mach., vol. 1:4, no. 1, pp. 31-34, 2006.
9. P. R. Johansen, D. Patterson, C. O'Keefe, and J. Swenson, "The use of an axial flux permanent magnet in-wheel direct drive in an electric bicycle," Renewable Energy, vol. 22, pp. 151-157, 2001.
10. Y. P. Yang, Y. P. Luh, and C. H. Cheung, "Design and control ofaxial flux brushless DC wheel motors for electric vehicles\-Part I: Multi -objective optimal design and analysis," IEEE Trans. Magn., vol. 40, no. 4, pp. 1873- 1882,2004.
11. F. Profumo, Z. Zhang, and A. Tenconi, "Axial flux machines drives. A new viable solution for electric cars," IEEE Trans. Ind. Electron., vol. 44, no. 1, pp. 39-45, 1997. (Pubitemid 127828620)
12. P. H. Mellor, T. Allen, and D. Howe, "Hub-mounted electric driven- train for a high performance all-electric vehicle," in IEE Colloq. Machines Drives Electric Hybrid Vehicles (Digest No.1996/152), London, U.K., 1996.
13. Y E. Zhao, J. W. Zhang, and X. Han, "Design and study on the dynamic- damper mechanism for an in-wheel motor individual drive electric vehicle," Mech. Sci. Technol. Aerosp. Eng., vol. 27, no. 3, pp. 395-398, 2008.
14. Z. Q. Zhu, D. Howe, E. Bolte, and B. Ackermann, "Instantaneous mag- netic field distribution in brushless permanent magnet DC motors," IEEE Trans. Magn., vol. 29, no. 1, pp. 124-151, Jan. 1993.
15. Z. Q. Zhu, D. Howe, and C. C. Chan, "An improved analytical model for predicting the magnetic field distribution in brushless permanent magnet motors," IEEE Trans. Magn., vol. 38, no. 1, pp. 229-238, Jan. 2002. (Pubitemid 34740943)
16. D. Zarko, D. Ban, and T. A. Lipo, "Analytical calculation ofmagnetic field distribution in the slotted air gap of a surface permanent-magnet motor using complex relative air-gap permeance," IEEE Trans. Magn., vol. 42, no. 7, pp. 1828-1837, Jul. 2006. (Pubitemid 44109312)
17. J. Wang, Z. P. Xia, S. A. Long, and D. Howe, "Radial force density and vibration characteristics of modular permanent magnet brushless ac machine," Proc. Inst. Elect. Eng.-Electr. Power Appl., vol. 153, no. 6, pp. 793-801, Nov. 2006. (Pubitemid 44598215)
18. A. M. El-Refaie, T. M. Jahns, and D. Novotny, "Analysis of surface PM machines with fractional-slot concentrated windings," IEEE Trans. Energy Convers., vol. 21, no. 1, pp. 34-43, Mar. 2006. (Pubitemid 43280516)
19. Z. Q. Zhu, Z. P. Xia, L. J. Wu, and G. W. Jewell, "Influence of slot and pole number combination on radial force and vibration modes in fractional slot PM brushless machines having single-and double-layer windings," in Proc. IEEE ECCE, San Jose, CA, Sep. 20-24, 2009, pp. 3443-3450.
20. F. Yu and Y Lin, Vehicle System Dynamics: China Machine, 2005.
21. Z. Q. Zhu and D. Howe, "Instantaneous magnetic field distribution in permanent magnet brushless dc motor, Part IV: Magnetic field on load," IEEE Trans. Magn., vol. 29, no. 1, Jan. 1993.
22. D. X. Cheng, Handbook of Mechanical Design. Beijing, China: Chem. Ind., 2004.