Low consistency refining of mechanical pulp, effect of gap, speed and power

Journal of Pulp and Paper Science

Volumn 36, Issue 3-4, 2010, Pages 28-34

  Luukkonen, A ^a   Olson, J A ^a   Martinez, D M ^a  

^a UNIVERSITY OF BRITISH COLUMBIA   (Canada)

Author keywords

[No Author keywords available]

Indexed keywords

DESIGN AND OPERATIONS; DESIGN VARIABLES; EXPERIMENTAL STUDIES; LOW CONSISTENCY; PREDICTIVE CORRELATION; PULP QUALITIES; SPECIFIC ENERGY; TEAR STRENGTH;

MECHANICAL PULP; REFINING;

PULP REFINING;

EID: 84865274094     PISSN: 08266220     EISSN: None     Source Type: Journal    
DOI: None     Document Type: Article

References (22)

1. MUENSTER, H., "Energy Savings in TMP by High Temperature LC/MC Refining", Proc. Intl. Mech. Pulping Conf., Oslo, Norway (2005).
2. SABOURIN, M., "Minimizing TMP Energy Consumption of Chip Pre-Treatment, RTS and Multiple Stage Low-Consistency Refining", Proc. Intl. Mech. Pulping Conf. TAPPI, Vol. 2, 839-893 (2007).
3. ZHA, Q., LANOUETTE, R., LAW K.-N., BOUSQUET, J.-P. and BUSSIERES, S., "Refining of Long Fibre Fraction after Fractionation", Preprints 94th Ann. Mtg., PAPTAC, B481-B487 (2008).
4. MUSSELMAN, R., LETARTE, D. and SIMARD, R., "Third Stage Low-Consistency Refining of TMP for Energy Savings and Quality Enhancement", Proc. 4th Intl. Refining Conf., Fuiggi, Italy (1997).
5. BRECHT, W., "A Method for the Comparative Evaluation of Bar-Equipped Beating Devices", Tappi J. 50(8):40A-44A (1967).
6. DANFORTH, D.W., "Theory/Practice", South. Pulp Paper Manuf. 32(7):52-53 (1969).
7. LUMIAINEN, J., "New Theory can Improve Practice", Pulp Paper 32(8):46-47 (1990).
8. MELTZER, F.P. and RAUTENBACH, R., "Neue möglichkeiten zur vorherbestimmung des technologischen mahlergebnisses", Das Papier 48(9):578-583 (1994).
9. LEIDER, P.J. and NISSAN, A.H., "Understanding the Disc Refiner -The Mechanical Treatment of Fibres", Tappi J. 60(10):85-89 (1977).
10. KEREKES, R.J., "Characterization of Pulp Refiners by a C-Factor", Nordic Pulp Paper Res. J., Vol. 1, 3 8 (1990).
11. MARTINEZ, M. and KEREKES R.J., "Forces on Fibres in Low-Consistency Refining", Tappi J. Vol. 12, 119 (1994).
12. PAGE, D.H., "The Beating of Chemical Pulps -The Action and the Effect", Proc. 9th Fund. Res. Symp., Cambridge, UK, Vol. 1, 1-38 (1990).
13. OLSON, J.A., DROZDIAK, J., MARTINEZ, M., GARNER, R., ROBERTSON, A.G. and KEREKES, R., "Characterizing Fibre Shortening in Low-Consistency Refining using a Comminution Model", Powder Technol., Vol. 129, 122-129 (2003).
14. LUMIAINEN, J., "Refining Intensity at Low Consistency -Critical Factors", Paper Technol. 32(11):22-26 (1991).
15. MOHLIN, U.-B., "Refining Intensity and Gap Clearance", Proc. 9th Refining Conf. Pira Intl. (2006).
16. FORGACS, O.L., "The Characterization of Mechanical Pulps", Pulp Paper Mag. Can., Convention Issue, 89-118 (1963).
17. MOHLIN, U.-B., "Fibre Development during Mechanical Pulp Refining", J. Pulp Paper Sci. 23(1):28-33 (1997).
18. BENNETT, P.D., JANSSON, S., TURT, V., LÖNNBERG, B.K. and GENCO, J.M., "Effect of Specific Edge Loading on Freeness Drop Coefficient", Proc. Engin. Conf., TAPPI, 505-516 (1996).
19. HAMMAR, L.-A., SALMEN, L., SANDBERG, C. and SUNDSTRÖM, L., "The Effect of Process Conditions on Pulp Quality Development at Low-Consistency Refining of Mechanical Pulp -TMP", Proc. Intl. Mechanical Pulping Conf., SPCI (2009).
20. LEBLANC, J. and LIGHT, J., "The Performance of Low and Medium Intensity Low Consistency Refining Plates", Preprints 79th Ann. Mtg., Tech. Sect., CPPA (1993).
21. HERBERT, W. and MARSH, P.G., "Mechanics and Fluid Dynamics of a Disk Refiner", Tappi J. 51(5):235-239 (1968).
22. PAGE, D.H., "A Theory for the Tensile Strength of Paper", Tappi J. 52(4):674-681 (1969).