Discrete ply model of circular pull-through test of fasteners in laminates

Composite Structures

Volumn 94, Issue 10, 2012, Pages 3082-3091

  Adam, Louis ^a,b   Bouvet, Christophe ^b   Castanié, Bruno ^b   Daidié, Alain ^b   Bonhomme, Elodie ^a  

^a AIRBUS   (France)

^b University of Toulouse Clement Ader Institute   (France)

Author keywords

Cohesive element; Composite joints; Experiment; FE modelling; Pull through

Indexed keywords

BOLTED JOINTS; EXPERIMENTS; FASTENERS; TESTING;

AERONAUTICAL STRUCTURES; COHESIVE ELEMENT; COMPOSITE JOINT; FE-MODELLING; FINITE ELEMENTS MODELS; GOOD CORRELATIONS; OUT OF PLANE LOADS; PULL-THROUGH;

STRUCTURAL DESIGN;

EID: 84862227295     PISSN: 02638223     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.compstruct.2012.05.008     Document Type: Article

References (29)

1. US Mil-Hbk 17A, Chapter 7: Structural element characterization.
2. Bouvet C., Castanié B., Bizeul M., Barrau J-J. Low velocity impact modelling in laminate composite panels with discrete interface elements. Int J Solids Struct 2009, 46:2809-2821.
3. Alkatan F., Stephan P., Daidie A., Guillot J. Equivalent axial stiffness of various components in bolted joints subjected to axial loading. Finite Elem Anal Des 2007, 43(8):589-598.
4. Fares Y., Chaussumier M., Daidie A., Guillot J. Determining the life cycle of bolts using a local approach and the Dang Van criterion. Fatigue Fract Eng Mater Struct 2006, 29(8):588-596.
5. Hung C.-L., Chang F.-K. Strength envelope of bolted composite joints under bypass loads. J Compos Mater 1996, 30:1402-1435.
6. Valenza A., Fiore V., Borsellino C., Calabrese L., DiBella G. Failure map of composite laminate mechanical joint. J Compos Mater 2007, 41:951-964.
7. Castanié B., Creze S., Barrau J.J., Lachaud F., Risse L. Experimental analysis of failure in filled hole compression tests. Compos Struct 2010, 92(5):1192-1199.
8. Persson E., Madenci E., Eriksson I. Delamination initiation of laminates with pin loaded holes. Theor Appl Fract Mec 1998, 30:87-101.
9. Ireman T., Ranvik et T., Erikksson I. On damage development in mechanically fastened composite laminates. Compos Struct 2000, 49(2):151-171.
10. McCarthy M.A., Lawlor V.P., Stanley W.F., McCarthy C.T. Bolt-hole clearance effects and strength criteria in single-bolt, single-lap, composite bolted joints. Compos Sci Technol 2002, 62:1415-1431.
11. Naik R.A., Crews J.H. Stress analysis method for clearance fit-bolt under bearings load. AIAA J 1985, 24:1348-1353.
12. Tong L. Bearing failure of composite bolted joints with non-uniform bolt-to-washer clearance. Compos Part A: Appl Sci Manuf 2000, 31:609-615.
13. Park H.-J. Effects of stacking sequence and clamping force on the bearing strengths of mechanically fastened joints in composite laminates. Compos Struct 2001, 53:213-221.
14. Park H.-J. Bearing failure analysis of mechanically fastened joints in composite laminates. Compos Struct 2001, 53:199-211.
15. Wang H.-S., Hung C.-L., Chang F.-K. Bearing failure of bolted composite joints. Part I: Experimental characterization. J Compos Mater 1996, 30(12):1284-1313.
16. Hung C.-L., Chang F.-K. Bearing failure of bolted composite joints. Part II: Model and verification. J Compos Mater 1996, 30(12):1359-1400.
17. Ekh J., Schön J., Melin L. Secondary bending in multi fastener, composite-to-aluminium single shear lap joints. Compos Part B 2005, 36(3):195-208.
18. Ekh J., Schön J. Effect of secondary bending on strength prediction of composite, single shear lap joints. Compos Sci Technol 2005, 65(6):953-965.
19. Freedman RN. A study of pull-through failures of mechanically fastened joints, Master Thesis, Naval Postgraduate School, Monterey, California; 1977.
20. Waters WA, Williams JG. Failure mechanisms of laminates transversely loaded by bolt push through. NASA Technical Memorandum TM 87603; 1985.
21. Kelly G., Hallström S. Strength and failure mechanisms of composite laminates subject to localised transverse loading. Compos Struct 2005, 69:301-314.
22. Banbury A., Kelly D. A study of fastener pull-through failure of composite laminates. Part 1: Experimental. Compos Struct 1999, 45(4):241-254.
23. Banbury A., Kelly D., Jain L. A study of fastener pull-through failure of composite laminates. Part 2: Failure prediction. Compos Struct 1999, 45(4):255-270.
24. Elder D., Verdaasdonk A., Thomson R. Fastener pullthrough in a carbon fibre epoxy composite joint. Compos Struct 2008, 86(1-3):291-298.
25. Bunyawanichakul P., Castanié B., Barrau J.J. Nonlinear finite element analysis of inserts in sandwich structures. Compos Part B 2008, 39:1077-1092.
26. Catalanotti G., Camanho P.P., Ghys P., Marques A.T. Experimental and numerical study of fastener pull-through in GFRP laminates. Compos Struct 2011, 94(1):239-245.
27. ASTM D7332 / D7332M - 09 Standard test method for measuring the fastener pull-through resistance of a fiber-reinforced polymer matrix composite.
28. Wisnom M.R. Modelling discrete failures in composites with interface elements. Compos Part A 2010, 11(7):795-805.
29. Hou J.P., Petrinic N., Ruiz C. A delamination criterion for laminated composites under low-velocity impact. Compos Sci Technol 2001, 61:2069-2074.