Experimental investigation on workability and strain hardening behaviour of Fe-C-0.5Mn sintered composites

Materials and Design

Volumn 41, Issue , 2012, Pages 349-357

  Selvakumar, N ^a   Mohan Raj, A P ^b   Narayanasamy, R ^c  

^a MEPCO SCHLENK ENGINEERING COLLEGE   (India)

^b Department of Mechanical Engineering   (India)

^c NATIONAL INSTITUTE OF TECHNOLOGY   (India)

Author keywords

[No Author keywords available]

Indexed keywords

CARBON CONTENT; COLD DEFORMATION; EXPERIMENTAL INVESTIGATIONS; IRON-BASED; MANGANESE CONTENT; RELATIVE DENSITY; SINTERED SPECIMEN; TRI-AXIAL STRESS STATE;

ASPECT RATIO; CARBON; LOADING; MANGANESE; POWDER METALLURGY; PREFORMING; STRAIN HARDENING;

SINTERING;

EID: 84861851526     PISSN: 02641275     EISSN: 18734197     Source Type: Journal    
DOI: 10.1016/j.matdes.2012.04.053     Document Type: Article

References (24)

1. Lall C. Fundamentals of powder metallurgy and metal injection molding, Monographs in P/M series No. 2, Metal Powder Industries Federation; 2008.
2. Talijan N.M., Trifunovic D.S., Trifunovic D.D. The influence of different iron powders on the friction properties of sintered friction materials based on iron. Mater Lett 2000, 46:255-260.
3. Simchi A., Pohl H. Effects of laser sintering processing parameters on the microstructure and densification of iron powder. Mater Sci Eng A 2004, 383:191-200.
4. Ding Hao, Ding Hua, Qiu Chun-Lin, Tang Zheng-you, zeng Jian-Min, Yang Ping, et al. Formability of trip/twip steel containing manganese of 18.8%. J Iron Steel Res Int 2011, 18(1):36-40.
5. Schilke Martin, Ahlström Johan, Karlsson Birger Low cycle fatigue and deformation behaviour of austenitic manganese steel in rolled and in as-cast conditions. Proc Eng 2010, 2(1):623-628.
6. Mohan Raj A.P., Selva Kumar N. Deformation behaviour of sintered Fe-C-Mn composite during cold upset forming. Mater Manuf Process 2011, 26(11):1388-1392.
7. Kuhn H.A., Downey C.L. Deformation characteristics and plasticity theory of sintered powder materials. Int J Powder Metall 1971, 7(1):15-25.
8. Abdel-Rahman M., El-Sheikh Workability in forging of powder metallurgy compacts. J Mater Process Technol 1995, 54:97-102.
9. Vujovic V., Shabaik A.H. A new workability criterion for ductile metals. J Eng Mater Technol 1986, 108:245-249.
10. Narayanasamy R., Pandey K.S. Some aspects of work hardening in sintered aluminium-iron composite preforms during cold axial forming. J Mater Process Technol 1998, 84(1-3):136-142.
11. Selvakumar N., Narayanasamy R. Phenomenon of strain hardening behaviour of sintered aluminium preforms during cold axial forming. J Mater Process Technol 2003, 142(2):347-354.
12. Narayanasamy R., Ramesh T., Pandey K.S. An investigation on instantaneous strain hardening behaviour in three dimensions of aluminium-iron composites during cold upsetting. J Mater Sci Eng A 2005, 394:149-160.
13. Inigoraj A.J.R., Narayanasamy R., Pandey K.S. Strain-hardening behaviour in sintered aluminium-3.5% alumina composite preforms during axial compression with and without annealing. J Mater Process Technol 1998, 84:143-148.
14. Selvakumar N., Narayanasamy R. Deformation behavior of cold upset forming of sintered Al-Fe composite preforms. J Eng Mater Technol 2005, 127:251-256.
15. Selvakumar N., Narayanasamy R., Pandey K.S. Some aspects of cold upset forming of sintered aluminium preforms using different lubricants. Mater Sci Technol 2004, 20:485-489.
16. Narayanasamy R., Ramesh T., Pandey K.S. Some aspects on workability of aluminium-iron powder metallurgy composites during cold upsetting. Mater Sci Eng A 2005, 391(1-2):418-426.
17. Narayanasamy R., Anandakrishnan V., Pandey K.S. Effect of geometric work-hardening and matrix work-hardening on workability and densification of aluminium-3.5% alumina composite during cold upsetting. Mater Des 2008, 29:1582-1599.
18. Doraivelu S.M., Gegel H.L., Gunasekara J.S., Malas J.C., Morgan J.T. A new yield function for compressible P/M materials. Int J Mech Sci 1984, 26:527-535.
19. Narayanasamy R., Selvakumar N., Pandey K.S. Phenomenon of instantaneous strain hardening behaviour of sintered Al-Fe composite preforms during cold axial forming. Mater Des 2007, 28:1358-1363.
20. Satish Kumar S.R., Santha Kumar A.R. Design of steel structures 2008, Indian Institute of Technology Madras, India.
21. Narayanasamy R., Ramesh T., Pandey K.S. An experimental investigation on strain hardening behaviour of aluminium-3.5% alumina powder metallurgy composite preform under various stress states during cold upset forming. Mater Des 2007, 28:1211-1223.
22. ASTM E9. Standard methods of compression testing of metallic materials at room temperature. Book of ASTM standards, vol. 8, Philadelphia (PA), ASM International; 1994. p. 382.
23. MPIF standard 42. Determination of density of compacted or sintered metal powder products. Metal Powder Industries Federation; 1977.
24. Rajesh Kannan A., Pandey K.S., Shanmugam S. Some investigation on the cold deformation behaviour of sintered iron-0.8% carbon alloy powder preforms. J. Mater. Process. Technol. 2008, 203:542-547.