Analysis of cutting mechanism by ball end mill using 3d-cad (chip area by inclined surface machining and cutting performance based on evaluation value

LEM 2005 - 3rd International Conference on Leading Edge Manufacturing in 21st Century

Volumn , Issue , 2005, Pages 1109-1114

  Iwabe, H ^a   Shimizu, K ^b   Sasaki, M ^c  

^a NIIGATA UNIVERSITY   (Japan)

^b 52F Tokyo Opera City   (Japan)

^c CS Technica Co   (Japan)

Author keywords

3d cad; Ball end milling; Chip area; Cutting mechanism; Cutting performance; Evaluation value; Inclined surface

Indexed keywords

BALL END MILLING; CHIP AREAS; CUTTING MECHANISMS; CUTTING PERFORMANCE; EVALUATION VALUE; INCLINED SURFACE;

CUTTING TOOLS; MANUFACTURE; MILLING (MACHINING); THREE DIMENSIONAL;

BALL MILLING;

EID: 84861596007     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper

References (21)

1. Y.Yamada, T.Aoki, Y.Tanaka, Y.Onishi, K.Kotani and K. Wakihira, Trans. Jpn. Soc. Mech. Eng., (in Japanese), Vol.60, No.577, C(1994), p.2906-2910.
2. H.Iwabe, E.Takeoka, T.Miyaguchi and H.Gai, J. of JSPE, (in Japanese), Vol.64, No.6(1998), p.808-812.
3. T.Hosoi and T.Hoshi, Trans. Jpn. Soc. Mech. Eng., (in Japanese), Vol.44, No.378, III(1978), p.722-731.
4. Y.Fujii and H.Iwabe, J. of JSPE, (in Japanese), Vol.54, No.12(1988), p.2301-2306.
5. K.Kasahara, A.Hirota and Y.Sasai, J. of JSPE, (in Japanese), Vol.69, No.3(2003), p.396-401.
6. T.Miyaguchi, M.Masuda, E.Takeoka and H.Iwabe, Prec. Eng., Vol.25.No.2(2001), p.145-154.
7. N.Koreta, T.Egawa, M.Kuroda, K.Watanebe and Y.Ii, J. of JSPE, (in Japanese), Vol.59, No.9(1993), p.1537-1542.
8. X.Zhao, N.Koreta and M.Tsutsumi, J. of JSPE, (in Japanese), Vol.64, No.12(1998), p.1826-1830.
9. M.Hao, T.Asao, H.Terai and Y.Mizugaki, J. of JSPE, (in Japanese), Vol.65, No.10(1999), p.1476-1480.
10. K.Kikkwa, Y.Mizugaki, M.Hao and H.Terai, J. of JSPE, (in Japanese), Vol.69, No.3(2003), p.407-411.
11. A.Saito, X.Zhao and M.Tsutsumi, J. of JSPE, (in Japanese), Vol.66, No.12(2000), p.1963-1967.
12. T.Kishinami, H.Suzuki and K.Saito, J. of JSPE, (in Japanese), Vol.46, No.10(1980), p.1303-1310.
13. T.Kishinami, H.Suzuki and K.Saito, J. of JSPE, (in Japanese), Vol.47, No.4(1981), p.459-465.
14. H.Tanaka, F.Obata, M.Ashimori and T.Matsubara, J. of JSPE, (in Japanese), Vol.64, No.7(1998), p.1047-1051.
15. Y.Fujii and H.Iwabe, J. of JSPE, (in Japanese), Vol.48, No.5(1982), p.649-654.
16. I.Takahashi, M.Anzai and T.Nakagawa, J. of JSPE, (in Japanese), Vol.65, No.6(1999), p.867-871.
17. H.Iwabe, K.Yamaguchi, K.Shimizu and K.Nakanishi, Trans. Jpn. Soc. Mech. Eng., (in Japanese), Vol.69, No.687, C(2003), p.3116-3123.
18. Y.Lu, Y.Takeuchi, I.Takahashi, M.Anzai and K.Kase, J. of JSPE, (in Japanese), Vol.69, No.4(2003), p.530-535.
19. Y.Lu, Y.Takeuchi, I.Takahashi and M.Anzai, J. of JSPE, (in Japanese), Vol.70, No.5(2004), p.695-699.
20. X.Zhao, M.Tsutsumi, N.Koreta, D.Ge and L.Chen, J. of JSPE, (in Japanese), Vol.62, No.7(1996), p.1019-1023.
21. X.Zhao, M.Tsutsumi, N.Koreta and D.Ge, J. of JSPE, (in Japanese), Vol.63, No.7(1997), p.992-996.