An inverse heat transfer method for determining workpiece temperature in minimum quantity lubrication deep hole drilling

Journal of Manufacturing Science and Engineering

Volumn 134, Issue 2, 2012, Pages

  Tai, Bruce L ^a   Stephenson, David A ^a   Shih, Albert J ^a  

^a UNIVERSITY OF MICHIGAN   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

HEAT FLUX; HEAT TRANSFER; INFILL DRILLING; INVERSE PROBLEMS; LUBRICATION; TEMPERATURE MEASUREMENT; THERMOCOUPLES;

BOTTOM SURFACES; DEEP HOLE DRILLING; EMBEDDED THERMOCOUPLES; INVERSE HEAT TRANSFER; INVERSE METHODS; MINIMUM QUANTITY LUBRICATION; SPATIAL AND TEMPORAL CHANGES; WORKPIECE TEMPERATURE;

BOREHOLES;

EID: 84859902805     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.4005794     Document Type: Article

References (15)

1. Stoll, A., Sebastian, A. J., Klosinski, R., and Furness R., 2008, "Minimum Quantity Lubrication (MQL) is a Key Technology for Driving the Paradigm Shift in Machining Operations," SAE Paper No. 01-1128.
2. Filipovic, A., and Stephenson, D., 2006, "Minimum Quantity Lubrication (MQL) Application in Automotive Powertrain Machining," Mach. Sci. Technol., 10, pp. 3-22. (Pubitemid 43348673)
3. Heinemann, R., Hinduja, S., Barrow, G., and Petuelli, G., 2006, "Effect of MQL on the Tool Life of Small Twist Drills in Deep-Hole Drilling," Int. J. Mach. Tools Manuf., 46, pp. 1-6. (Pubitemid 41497894)
4. Liao, Y. S., and Lin, H. M., 2007, "Mechanism of Minimum Quantity Lubrication in Highspeed Milling of Hardened Steel," Int. J. Mach. Tools Manuf., 47, pp. 1660-1666. (Pubitemid 46634975)
5. Autret, R., and Liang, S. Y., 2003, "Minimum Quantity Lubrication in Finish Hard Turning," HNICEM '03.
6. Silva, L. R., Bianchi, E. C., Catai, R. E., Fusse, R. Y., and Franca, T. V., 2005, "Study on the Behavior of the Minimum Quantity Lubricant-MQL Technique Under Different Lubricating and Cooling Conditions When Grinding ABNT 4340 Steel," J. Braz. Soc. Mech. Sci. Eng., 27(2), pp. 192-199. (Pubitemid 40860547)
7. Stephenson, D. A., and Agapiou, J. S., 2006, Metal Cutting Theory and Practice, 2nd ed., Taylor & Francis, Boca Raton, FL.
8. Agapiou, J. S., and Stephenson, D. A., 1994, "Analytical and Experimental Studies of Drill Temperature," Trans. ASME, 116, pp. 54-60.
9. Bono, M., and Ni, J., 2006, "The Location of the Maximum Temperature on the Cutting Edges of a Drill," Int. J. Mach. Tools Manuf., 46, pp. 901-907.
10. Li, R., and Shih, A. J., 2007, "Tool Temperature in Titanium Drilling," ASME J. Manuf. Sci. Eng., 129, pp. 740-749. (Pubitemid 47437100)
11. Bono, M., and Ni, J., 2001, "The Effects of Thermal Distortions on the Diameter and Cylindricity of Dry Drilled Holes," Int. J. Mach. Tools Manuf., 41, pp. 2261-2270. (Pubitemid 32785160)
12. Bono, M., and Ni, J., 2002, "A Model for Predicting the Heat Flow Into the Workpiece in Dry Drilling," ASME J. Manuf. Sci. Eng., 124, pp. 773-777. (Pubitemid 35384296)
13. Ke, F., Ni, J., and Stephenson, D. A., 2005, "Continuous Chip Formation in Drilling," Int. J. Mach. Tools Manuf., 45(150), pp. 1652-1658. (Pubitemid 41344907)
14. Li, R., and Shih, A. J., 2007, "Finite Element Modeling of High-Throughput Drilling of Ti-6Al-4V," Trans. NAMRI/SME, 35, pp. 73-80. (Pubitemid 47266639)
15. Papalambros, P. Y., and Wilde, D. J., 2000, Principles of Optimal Design: Modeling and Computation, 2nd ed., Cambridge University Press, New York.