Feasibility study of thin microinjection molded components

Polymer Engineering and Science

Volumn 52, Issue 1, 2012, Pages 180-190

  Mahmoodi, Mehdi ^a   Park, Simon S ^a   Rizvi, Ghaus ^b  

^a UNIVERSITY OF CALGARY   (Canada)

^b UNIVERSITY OF ONTARIO INSTITUTE OF TECHNOLOGY   (Canada)

Author keywords

[No Author keywords available]

Indexed keywords

BLOWING AGENTS; COMMINUTION; FLOW PATTERNS; MICROOPTICS; WOOD PRODUCTS;

CHEMICAL BLOWING AGENTS; DIMENSIONAL ACCURACY; FEASIBILITY STUDIES; FILLING BEHAVIOUR; LINEAR LOW-DENSITY POLYETHYLENE; MICRO-INJECTION; MINIATURISATION; MOLDED PARTS; STRONG DEMAND; WOODFIBER;

COST EFFECTIVENESS;

BLOWING; COMPUTER PROGRAMS; COST EFFECTIVENESS; DIMENSIONAL STABILITY; INJECTION MOLDING; MINIATURIZATION; POLYETHYLENE; POLYMERS; WOOD FIBERS;

EID: 83555174301     PISSN: 00323888     EISSN: 15482634     Source Type: Journal    
DOI: 10.1002/pen.22062     Document Type: Article

References (28)

1. W. Michaeli, and, D. Opfermann, Microsyst. Technol., 12, 616 (2006).
2. L. Yu, C.G. Koh, L.J. Lee, K.W. Koelling, and, M.J. Madou, Polym. Eng. Sci., 12, 616 (2002).
3. C.D. Chin, V. Linder, and, S.K. Sia, Lab Chip, 12, 616 (2007).
4. R.D. Chien, Sens. Actuators A, 12, 616 (2006).
5. W.C. Jung, Y.M. Heo, G.S. Yoon, K.H. Shin, S.H. Chang, G.H. Kim, and, M.W. Cho, Sensors, 12, 616 (2007).
6. J. Chae, S.S. Park, and, T. Freiheit, Int. J. Mach. Tool Manufact., 12, 616 (2006).
7. D. Bibber, "Micro Molding Challenges," in Proceedings of the 62nd Annual Technical Conference, ANTEC, Chicago, IL, May 16-20 (2004).
8. M. Heckele, and, W.K. Schomburg, J. Micromech. Microeng., 14, R1 (2004).
9. C. Kwag, C.W. Manke, and, E. Gulari, J. Polym. Sci. Part B: Polym. Phys., 12, 616 (1999).
10. C. Kwag, C.W. Manke, and, E. Gulari, Ind. Eng. Chem. Res., 12, 616 (2001).
11. J.R. Royer, Y.J. Gay, J.M. Desimone, and, S.A. Khan, J. Polym. Sci. Part B: Polym. Phys., 12, 616 (2000).
12. N.P. Suh, "Microcellular Plastics," in Innovation in Polymer Processing-Molding, J.F. Stevenson, Ed., Hanser Publishers, Munich, 93 (1996).
13. Z. Zhang, and, Y.P. Handa, J. Polym. Sci. Part B: Polym. Phys., 12, 616 (1998).
14. A. Kramschuster, R. Cavitt, D. Ermer, Z. Chen, and, L.S. Turng, Polym. Eng. Sci., 12, 616 (2005).
15. S.Y. Yang, S.C. Nian, S.T. Huang, and, Y.J. Weng, Polym. Adv. Technol., 22 (6), 891 (2009).
16. S.M. Lee, Handbook of Composite Reinforcements, VCH Publishers, New York, NY (1993).
17. S.Y. Zhang, Y. Zhang, M. Bousmina, M. Sain, and, P. Choi, Polym. Eng. Sci. 47, 1678 (2007).
18. W.H. Yang, A. Peng, L. Liu, D.C. Hsu, and, R.Y. Chang, "Integrated Numerical Simulation of Injection Molding Using True 3d Approach," in Proceedings of the 62nd Annual Technical Conference, ANTEC, Chicago, IL, 486, May 16-20 (2004).
19. T. Manzione, Ed., Applications of Computer Aided Engineering in Injection Molding, Hanser Publishers, Manich-Vienna-New York (1987).
20. B.J. Araujo, J.C.F. Teixeira, A.M. Cunha, and, C.P.T. Groth, Int. J. Numer. Meth Fluid, 12, 616 (2009).
21. Y.K. Shen, and, W.Y. Wu, Int.Comm. Heat Mass Transfer, 12, 616 (2002).
22. C.A. Hieber, and, S.F. Shen, J. Non-Newtonian Fluid Mech., 12, 616 (1980).
23. H.H. Chiang, C.A. Hieber, and, K.K. Wang, Polym. Eng. Sci., 12, 616 (1991).
24. K. Park, Polym. Plast. Tech. Eng., 12, 616 (2004).
25. M.M. Cross, Rheol. Acta, 12, 616 (1979).
26. C.A. Hieber, "Melt-Viscosity Characterization and Its Application to Injection Molding," in Injection and Compression Molding Fundamentals, A.I. Isayev, Ed., Marcel Dekker, Inc., New York, 1 (1987).
27. T. Whelan, Polymer Technology Dictionary, Chapman & Hall Pub., London (1994).
28. J.M. Fischer, Handbook of Molded Part Shrinkage and Warpage, Plastics Design Library/William Andrew Inc., Norwich, NY (2003).