TDC offset estimation from motored cylinder pressure data based on heat release shaping;Estimation du décalage de PMH à partir de données de pression de cylindre moteur basées sur la conformation de libération de chaleur

Oil and Gas Science and Technology

Volumn 66, Issue 4, 2011, Pages 705-716

  Tunestal P ^a  

^a LUND UNIVERSITY   (Sweden)

Author keywords

[No Author keywords available]

Indexed keywords

COMBUSTION CHAMBER WALLS; CRANK ANGLE; CUT-OFF; CYLINDER PRESSURE DATA; CYLINDER PRESSURES; HEAT RELEASE; LOSS POWER; NONLINEAR LEAST-SQUARES OPTIMIZATION; NOVEL METHODS; OFFSET ESTIMATION; ON-BOARD DIAGNOSTICS; PEAK PRESSURE; SINGLE CYCLE; SPECIFIC HEAT RATIO; STANDARD DEVIATION; THIRD ORDER; TOP DEAD CENTER;

COMBUSTION; COMBUSTION CHAMBERS; DIESEL ENGINES; ENGINE CYLINDERS; FOURIER ANALYSIS; FOURIER SERIES; HEAT LOSSES; LEAST SQUARES APPROXIMATIONS; SPECIFIC HEAT; STATISTICS; UNCERTAINTY ANALYSIS;

ESTIMATION;

CALIBRATION; COMBUSTION; ENGINE; ESTIMATION METHOD; LEAST SQUARES METHOD; OPTIMIZATION; SENSOR;

EID: 80655147977     PISSN: 12944475     EISSN: None     Source Type: Journal    
DOI: 10.2516/ogst/2011144     Document Type: Article

References (13)

1. Brunt M.F.J., Emtage A.L. (1996) Evaluation of IMEP routines and analysis errors, SAE Technical paper 960609.
2. Heywood J.B. (1988) Internal Combustion Engine Fundamentals, McGraw-Hill, pp. 384-385.
3. Tazerout M., Le Corre O., Rousseau S. (1999) TDC determination in IC engines based on the thermodynamic analysis of the temperature-entropy diagram, SAE Technical paper 1999- 01-1489.
4. Stas M.J. (1996) Thermodynamic determination of T.D.C. in piston combustion engines, SAE Technical paper 960610.
5. Stas M.J. (200) An universally applicable thermodynamic method for T.D.C. determination, SAE Technical paper 2000-01-0561.
6. Eriksson L. (1998) Requirements for and a systematic method for identifying heat-release model parameters, SAE Technical paper 980626.
7. Xi-Bo Wang, Kang-Yao Deng, Fang-Zheng He, Zhen-Hua Zhou (2007) A thermodynamics model for the compression and expansion process during the engine's motoring and a new method for the determination of TDC with simulation technique, Appl. Therm. Eng. 27, 11-12, 2003-2010.
8. Nilsson Y., Eriksson L. (2004) Determining TDC position using symmetry and other methods, SAE Technical paper 2004-01-1458.
9. Chang H., Zhang Y., Chen L. (2005) An applied thermodynamic method for correction of TDC in the indicator diagram and its experimental confirmation, Appl. Therm. Eng. 25, 5-6, 759-768.
10. Tunestal P. (2009) Model Based TDC Offset Estimation from Motored Cylinder Pressure Data, 2009 IFAC Workshop on Engine and Powertrain Control, Simulation and Modeling, 2008.
11. Tunestal P. (2009) Self-tuning gross heat release computation for internal combustion engines, Control Eng. Pract., 17, 4, 518-524.
12. Tunestal P. (2001) Estimation of the In-Cylinder Air/Fuel Ratio of an Internal Combustion Engine by the Use of Pressure Sensors, PhD Thesis, Lund University, Faculty of Engineering.
13. Wilhelmsson C., Vressner A., Tunestal P., Johansson B., Särner G., Aldén M. (2005) Combustion chamber wall temperature measurement and modeling during transient HCCI operation, SAE Technical paper 2005-01-3731.