Similarities and differences between the flow factor method by Patir and Cheng and homogenization

Journal of Tribology

Volumn 133, Issue 3, 2011, Pages

  Almqvist, Andreas ^a   Fabricius, John ^a   Spencer, Andrew ^a   Wall, Peter ^a  

^a LULEÅ UNIVERSITY OF TECHNOLOGY   (Sweden)

Author keywords

flow factors; homogenization; hydrodynamic lubrication; Patir and Cheng; Reynolds equation; surface roughness

Indexed keywords

FLOW FACTORS; HOMOGENIZATION; HYDRODYNAMIC LUBRICATION; PATIR AND CHENG; REYNOLDS;

HYDRODYNAMICS; LUBRICATION; REYNOLDS EQUATION; SURFACE PROPERTIES; SURFACE ROUGHNESS;

HOMOGENIZATION METHOD;

EID: 79961187475     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.4004078     Document Type: Article

References (23)

1. Almqvist, T., and Larsson, R., 2004, "Some Remarks on the Validity of Reynolds Equation in the Modeling of Lubricant Film Flows on the Surface Roughness Scale," J. Tribol., 126(4), pp. 703-710. (Pubitemid 40015156)
2. Cioranescu, D., and Donato, P., 1999, An Introduction to Homogenization, of Oxford Lecture Series in Mathematics and its Applications, Clarendon, Oxford, Oxford University, New York, Vol. 17.
3. Patir, N., and Cheng, H. S., 1978 "An Average Flow Model for Determining Effects of Three-Dimensional Roughness on Partial Hydrodynamic Lubrication," Trans. ASME, J. Tribol., 100, pp. 12-17. (Pubitemid 8572530)
4. Patir, N., and Cheng, H. S., 1979, "Application of Average Flow Model to Lubrication Between Rough Sliding Surfaces," Trans. ASME, J. Tribol., 101, pp. 220-230. (Pubitemid 9479317)
5. Bayada, G., and Faure, J., 1989, "A Double Scale Analysis Approach of the Reynolds Roughness; Comments and Application to the Journal Bearing," Trans. ASME, J. Tribol., 111(2), pp. 323-330.
6. Almqvist, A., Larsson, R., and Wall, P., 2007, "The Homogenization Process of the Time Dependent Reynolds Equation Describing Compressible Liquid Flow," Tribol. -Finn. J. Tribol., 26(4), pp. 30-44.
7. Bayada, G., Ciuperca, I., and Jai, M., 2006, "Homogenized Elliptic Equations and Variational Inequalities with Oscillating Parameters. Application to the Study of Thin Flow Behavior With Rough Surfaces," Nonlinear Anal.: Real World Appl., 7(5), pp. 950-966. (Pubitemid 43903673)
8. Kane, M., and Bou-Said, B., 2004, "Comparison of Homogenization and Direct Techniques for the Treatment of Roughness in Incompressible Lubrication," Trans. ASME, J. Tribol., 126(4), pp. 733-737. (Pubitemid 40015160)
9. Kane, M., and Bou-Said, B., 2005, "A Study of Roughness and Non-Newtonian Effects in Lubricated Contacts," Trans. ASME, J. Tribol., 127, pp. 575-581. (Pubitemid 40990360)
10. Martin, S., 2008, "Influence of Multiscale Roughness Patterns in Cavitated Flows: Applications to Journal Bearings," Math. Probl. Eng., 2008, pp. 1-26.
11. Almqvist, A., Essel, E. K., Fabricius, J., and Wall, P., 2008, "Reiterated Homogenization Applied in Hydrodynamic lubrication," Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 222(7), pp. 827-841.
12. Almqvist, A., Essel, E. K., Persson, L.-E., and Wall, P., 2007, "Homogenization of the Unstationary Incompressible Reynolds Equation," Tribol. Int., 40(9), pp. 1344-1350. (Pubitemid 46855999)
13. Almqvist, A., and Dasht, J., 2006, "The Homogenization Process of the Reynolds Equation Describing Compressible Liquid Flow," Tribol. Int., 39(9), pp. 994-1002. (Pubitemid 44108396)
14. Sahlin, F., Larsson, R., Marklund, P., Lugt, P. M., and Almqvist, A., 2010, "A Mixed Lubrication Model Incorporating Measured Surface Topography. Part 1: Theory of Flow Factors," Proc. Inst. Mech. Eng., Part J:J. Eng. Tribol., 224(4), pp. 335-351.
15. Sahlin, F., Larsson, R., Marklund, P., Lugt, P. M., and Almqvist, A., 2010, "A Mixed Lubrication Model Incorporating Measured Surface Topography. Part 2: Roughness Treatment, Model Validation, and Simulation," Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 224(4), pp. 353-365.
16. Tripp, J. H., 1983, "Surface Roughness Effects in Hydrodynamic Lubrication: The Flow Factor Method," Trans. ASME, J. Tribol., 105(3), pp. 458-465. (Pubitemid 13555930)
17. Lunde, L., and Tonder, K., 1997, "Pressure and Shear Flow in a Rough Hydrodynamic Bearing Flow Factor Calculation," Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 119(3), pp. 549-555.
18. Harp, S. R., and Salant, R. F., 2001, "An Average Flow Model of Rough Surface Lubrication With Inter-Asperity Cavitation," Trans. ASME, J. Tribol., 123(1), pp. 134-143. (Pubitemid 32696612)
19. Kim, T. W., and Cho, Y. J., 2008, "The Flow Factors Considering the Elastic Deformation for the Rough Surface with a Non-Gaussian Height Distribution," Tribol. Trans., 51(2), pp. 213-220.
20. Meng, F., Wang, Q. J., Hua, D., and Liu, S., 2010, "A Simple Method to Calculate Contact Factor used in Average Flow Model," Trans. ASME, J. Tribol., 132(2), pp. 024505.
21. Reynolds, O., 1886, "On the Theory of Lubrication and Its Application to Mr. Beauchamps Tower's Experiments, Including an Experimental Determination of the Viscosity of Olive Oil," Philos. Trans. R. Soc. London A, 177, pp. 157-234.
22. Hamrock, B. J., 1994, Fundamentals of Fluid Film Lubrication, McGraw-Hill, New York.
23. Almqvist, A., 2009, On the Effects of Roughness in Lubrication, Lambert Academic Publishing, Saarbrücken.