Radiation curing: Coatings and composites

Nukleonika

Volumn 55, Issue 1, 2010, Pages 97-106

  Berejka, Anthony J ^a   Montoney, Daniel ^b   Cleland, Marshall R ^c   Loiseau, Loïc ^d  

^a Ionicorp+   (United States)

^b Strathmore Products   (United States)

^c IBA Industrial Inc   (United States)

^d IBA Group   (Belgium)

Author keywords

Coatings; Electron beam; Fiber composites; Matrices; Radiation curing; X ray

Indexed keywords

EID: 79960881590     PISSN: 00295922     EISSN: 15085791     Source Type: Journal    
DOI: None     Document Type: Review

References (18)

1. Berejka AJ (2003) Electron beam curing of coil coatings. The RadTech Report, (September/October 2003), pp 47-53.
2. Berejka AJ (2007) Barriers to the commercial acceptance of radiation processing in the manufacture of fiber reinforced composites. In: Proc of SAMPE 2007, June 3-7, 2007, Baltimore, MD, USA.
3. Berejka AJ (2007) X-ray curing of fiber composites - feasibility study. Co-funded study for the New York State Energy Research and Development Authority. Contract 9097 (November 9, 2007), Albany, NY, USA.
4. Berejka AJ, Cleland MR, Galloway RA, Gregoire O (2005) X-ray curing of composite materials. Nucl Instrum Methods Phys Res B 241:847-849.
5. Brenner W, Oliver WF (1967) Commercial aspects of instantaneous radiation cure of reinforced plastics. SPE Journal 23;4:33ff.
6. Campbell FJ, Brenner W, Johnson LM, White ME (1979) Radiation curing (Task D), (part of a Naval Research Laboratory report), USA
7. Campbell FJ, Brenner W, Johnson LM, White ME (1979) Radiation curable resins, (part of a larger report), USA, pp 79-92
8. Canady V, Berejka AJ, Whitney W (1975) Report on creep and flow characterization of Raychem adhesives. Submittal to the Trans-Alaskan Pipeline System, Raychem Corporation, Menlo Park, California, USA.
9. Charlesby A (1960) Atomic radiation and polymers. Pergamon Press, New York, p 417.
10. Cleland MR, Berejka AJ, Sampa MH et al. (2010) Industrial electron beam processing. International Atomic Energy Agency Working Material - rev. 3. IAEA, Vienna, Austria (February 2010).
11. Coqueret X, Defoort B, Dupillier JM, Larnac G (2003) Polymerization kinetics of acrylate monomers under UV/EB radiation: from labscale monitoring to the modeling of industrial curing. In: Proc of the UV/EB - Meeting the Challenge, Radtech Europe, November 3-5, 2003, Berlin, Germany.
12. Felis K, Avnery T, Berejka AJ (2002) Innovative energy efficient low voltage electron beam emitters. Radiat Phys Chem 63:605-608.
13. Herer A, Galloway RA, Cleland MR et al. (2009) X-ray cured carbon-fiber composites for vehicle use. Radiat Phys Chem 78:531-534.
14. Larsen LS (2000) Electron beam cured coatings for metals. Student award presentation to the Council on Ionizing Radiation Measurements and Standards (November 1, 2000).
15. Morales T, Rueda E, Christmas B (2008) The relative effects of AC- and DC-powered UV lamp systems on the properties of UV-polymerized films. In: Proc of the RadTech International North America UV& EB Curing Technology Conf, May 4-7, 2008, Chicago, IL, USA.
16. Ponsaud P, Defoort B, Coqueret X (2005) A microstructural investigation of UV and EB-cured bisphenol-A ethoxy diacrylate by 1H NMR relaxation measurements. In: Proc of the SAMPE 2005, May 1-5, 2005, Long Beach, CA, USA.
17. Spadaro G, Dispenza C, Fuochi P, Lavalle M, Corda U, Alessi S (2005) Epoxy based matrices for structural composites prepared by ionizing radiation. In: Proc of the IAEA Consultants Meeting on Radiation Curing of Composites, August 8-11, 2005, Sao Paulo, Brazil.
18. VanLandingham MR, Eduljee RF, Cillespie Jr JW (1999) Relationships between stoichiometry, microstructure, and properties for amine-cured epoxies. J Appl Polym Sci 71:699-712.