Test method development for deformation analysis of injection moulded plastic parts

Polymer Testing

Volumn 30, Issue 5, 2011, Pages 543-547

  Kovacs J G ^a   Siklo B ^a  

^a BUDAPEST UNIVERSITY OF TECHNOLOGY AND ECONOMICS   (Hungary)

Author keywords

Corner effect; Deformation; Injection mould; Injection moulding; Warpage

Indexed keywords

CHARACTERISATION; COMPLEX NATURE; CORNER EFFECTS; DEFORMATION ANALYSIS; EDGE LENGTH; ELEMENT DESIGN; GLASS FIBRES; HOLDING PRESSURE; INJECTION MOULD; INJECTION MOULDING; MOULD DESIGN; MOULD TEMPERATURE; NOVEL METHODS; TECHNOLOGICAL PARAMETERS; TEST METHOD; WARPAGES;

DEFORMATION; GLASS FIBERS; INJECTION MOLDING; PLASTIC MOLDS;

PLASTIC PARTS;

EID: 79955968126     PISSN: 01429418     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.polymertesting.2011.04.011     Document Type: Article

References (21)

1. J.M. Fischer Handbook of Moulded Part Shrinkage and Warpage first ed. 2003 Plastics Design Library/William Andrew Inc Norwich
2. M. Altan Reducing shrinkage in injection mouldings via the Taguchi, ANOVA and neural network methods Mater. Design 31 1 2010 599
3. K.M.B. Jansen, D.J.v. Dijk, and E.V. Burgers Experimental validation of shrinkage predictions for injection moulded products Int. Polym. Proc. 13 1 1998 99
4. X. Chen, and F. Gao A study of packing profile on injection moulded part quality Mater. Sci. Eng. 358 1-2 2003 205
5. K.M.B. Jansen, R. Pantani, and G. Titomanlio As-moulded shrinkage measurements on polystyrene injection moulded products Polym. Eng. Sci. 38 2 1998 254
6. P. Postawa, and J. Koszkul Change in injection moulded parts shrinkage and weight as a function of processing conditions J. Mater. Process Tech. 162-163 2005 109
7. A. Demirer, Y. Soydan, and A.O. Kapti An experimental investigation of the effects of hot runner system on injection moulding process in comparison with conventional runner system Mater. Design 28 5 2007 1467
8. K.M.B. Jansen, D.J. van Dijk, and K.P. Keizer Warpage of injection moulded plates and corner products Int. Polym. Proc. 13 4 1998 417
9. M. Akay, S. Ozden, and T. Tansey Prediction of process-induced warpage in injection moulded thermoplastics Polym. Eng. Sci. 1996 13 1839 36
10. S.H. Tang, Y.J. Tan, S.M. Sapuan, S. Sulaiman, N. Ismail, and R. Samin The use of Taguchi method in the design of plastic injection mould for reducing warpage J. Mater. Process Tech. 182 1-3 2007 418
11. S.H. Tang, Y.M. Kong, S.M. Sapuan, R. Samin, and S. Sulaiman Design and thermal analysis of plastic injection mould J. Mater. Process Tech. 171 2 2006 259
12. E.J. Fahy Modeling warpage in reinforced polymer disks Polym. Eng. Sci. 38 7 1998 1072
13. H. Kikuchi, and K. Koyama Generalized warpage parameter Polym. Eng. Sci. 36 10 1996 1309
14. H. Kikuchi, and K. Koyama The relation between thickness and warpage in a disk injection moulded from fibre reinforced PA66 Polym. Eng. Sci. 36 10 1996 1317
15. R. Zheng, P. Kennedy, N. Phan-Thien, and X.J. Fan Thermoviscoelastic simulation of thermally and pressure-induced stresses in injection moulding for the prediction of shrinkage and warpage for fibre-reinforced thermoplastics J. Non-Newton Fluid 84 2-3 1999 159
16. K. Prashantha, J. Soulestin, M.F. Lacrampe, E. Lafranche, P. Krawczak, G. Dupin, and M. Claes Taguchi analysis of shrinkage and warpage of injection-moulded polypropylene/multiwall carbon nanotubes nanocomposites Express Polym. Lett. 3 10 2009 630
17. K.K. Kabanemi, H. Vaillancourt, H. Wang, and G. Salloum Residual stresses, shrinkage, and warpage of complex injection moulded products: Numerical simulation and experimental validation Polym. Eng. Sci. 38 1 1998 21
18. B. Mlekusch The warpage of corners in the injection moulding of short-fibre-reinforced thermoplastics Compos Sci. Technol. 1999 12 1923 59
19. A. Ammar, V. Leo, and G. Régnier Corner deformation of injected thermoplastic parts Int. J. Form Proc. 6 1 2003 53
20. J.G. Kovács, and B. Sikló Experimental validation of simulated weld line formation in injection moulded parts Polym. Test. 29 7 2010 910
21. B. Solymossy, and J.G. Kovács The examination of weld line properties in injection moulded PP composites Mater. Sci. Forum 589 2008 263