Merged neural decision system and anfis wear predictor for supporting tool condition monitoring

Transactions of Famena

Volumn 35, Issue 1, 2011, Pages 13-26

  Župerl, Uroš ^a   Cuš, Franci ^a  

^a UNIVERSITY OF MARIBOR   (Slovenia)

Author keywords

ANFIS; End milling; Neural network; Tool condition monitoring (TCM); Tool deflection; Wear

Indexed keywords

EID: 79954592886     PISSN: 13331124     EISSN: None     Source Type: Journal    
DOI: None     Document Type: Article

References (17)

1. Fu, P., Hope, A.D. (2008). Intelligent Classification of Cutting Tool Wear States. Advances in Neural Networks, vol. 39, p. 1611-3349.
2. Mulc, T., Udiljak, T., Cus, F., Milfelner, M. (2004). Monitoring cutting- tool wear using signals from the control system. Strojniški vestnik - Journal of Mechanical Engineering, vol. 50, no. 12, p. 568-579. (Pubitemid 40213056)
3. Kuo, R. J. (2003). Multi-sensor integration for on-line tool wear estimation through artificial neural networks and fuzzy neural network. Engineering Applications of Artificial Intelligence, vol. 3, p. 49-261.
4. Achiche, S., Balazinski, M., Baron, L., Jemielniak, K. (2008). Tool wear monitoring using geneticallygenerated fuzzy knowledge bases. Engineering Applications of Artificial Intelligence, vol. 15, p. 303-314.
5. Kopac, J. (2002). Cutting forces and their influence on the economics of machining. Strojniški vestnik - Journal of Mechanical Engineering, vol. 48, no. 3, p. 72-79.
6. Iqbal, A., He, N., Dar, N. U., Li, L. (2009). Comparison of fuzzy expert system based strategies of offline and online estimation of flank wear in hard milling process. Expert Systems with Applications, vol. 33, p. 61-66. (Pubitemid 44959917)
7. Haber, R.E., Alique, A. (2005). Intelligent process supervision for predicting tool wear in machining processes. Mechatronics, vol. 13, p. 825-849.
8. Chien, W. T., Tsai, C. S. (2005). The investigation on the prediction of tool wear and the determination of optimum cutting conditions in machining 17-4PH stainless steel. Journal of Materials Processing Technology, vol. 140, p. 340-345.
9. Cuš, F., Župerl, U. (2007). Adaptive self-learning controller design for feedrate maximization of machining process. Advances in Production Engineering & Management, vol. 2, no. 1, p. 18-27.
10. Smaoui, M., Bouaziz, Z., Zghal, A. (2008). Simulation of cutting forces for complex surfaces in ball-end milling. International Journal of Simulation Modelling, vol. 7, no. 2, p. 93-105.
11. Župerl, U., Cuš, F. (2004). Tool cutting force modelling in ball-end milling using multilevel perceptron. J. mater. process. technol., vol. 153/154, p. 268-275.
12. Norgaard, M., Ravn, O., Poulsen, N. K., Hansen, L. K. (2000). Neural networks for modelling and control of dynamic systems. Springer, London, 2000.
13. Dweiri, F., Al-Jarrah, M., Al-Wedyan, H. (2001). Fuzzy surface roughness modeling of CNC down milling of Alumic-79. J. mater. process. technol, vol. 133, p. 266-275.
14. Shoorehdeli, M. A., Teshnehlab, M., Sedigh, A. K., Khanesar, A. (2009). Identification using ANFIS with intelligent hybrid stable learning algorithm approaches and stability analysis of training methods. Applied Soft Computing, vol. 9, no. 2, p. 833-850.
15. Sirkant, R., Subrahmanyam, S., Chen, K., Krishna, V. P. (2010). Experimental selection of special geometry cutting tool for minimal tool wear. Advances in Production Engineering & Management, vol. 5, no. 1, p. 13-24.
16. Milfelner, M., Zuperl, U., Cus, F. (2004). Optimisation of cutting parameters in high speed milling process by GA. International Journal of Simulation Modelling, vol. 3, no. 4, p. 121-131.
17. Wang, J., Huang, C.Z., Song, W.G. (2003). The effects of tool flank wear on the orthogonal cutting process and its practical implications. Journal of Materials Processing Technology, vol. 142, p. 338-346.