Slurry erosion behaviors of basalt filled low density polyethylene composites

Materials and Design

Volumn 32, Issue 5, 2011, Pages 3106-3111

  Akinci, Akin ^a   Ercenk, Ediz ^a   Yilmaz, Senol ^a,b   Sen, Ugur ^a  

^a SAKARYA UNIVERSITY   (Turkey)

^b MATERIALS INSTITUTE   (Turkey)

Author keywords

[No Author keywords available]

Indexed keywords

EROSION RATES; EROSION TEST; FILLED COMPOSITES; FRACTURE TOUGHNESS TESTS; MATRIX; MICRO-STRUCTURAL; SLURRY EROSION; SLURRY MEDIA; WORN SURFACE;

CONTACT ANGLE; EROSION; FRACTURE; FRACTURE TOUGHNESS; HARDNESS; POLYETHYLENES; TENSILE STRAIN; TENSILE STRENGTH; TERNARY SYSTEMS; THERMOPLASTICS; WEAR RESISTANCE;

BASALT;

EID: 79952195528     PISSN: 02641275     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.matdes.2010.12.029     Document Type: Article

References (30)

1. Hassani S., Klemberg-Sapieha J.E., Bielawski M. Design of hard coating architecture for the optimization of erosion resistance. Wear 2008, 265:879-887.
2. Hussainova I., Schade K.P. Correlation between solid particle erosion of cermets and particle contact dynamics. Tribol Int 2008, 41:323-330.
3. Kulu P., Hussainova I., Veinthal R. Solid particle erosion of thermal sprayed coatings. Wear 2005, 258:488-496.
4. Al-Bukhaiti M.A., Ahmed S.M., Badran F.M.F., Emara K.M. Effect of impingement angle on slurry erosion behavior and mechanisms of 1017 steel and high-chromium white cast iron. Wear 2007, 262:1187-1198.
5. Burstein G.T., Sasaki K. Effect of contact angle on the slurry erosion-corrosion of 304L stainless steel. Wear 2000, 240:80-94.
6. Oka Y.I., Ohnogi H., Hosokawa T., Matsumura M. The contact angle dependence of erosion damage caused by solid particle contact. Wear 1997, 203-204:573-579.
7. Clark H.M., Wong K.K. Contact angle, particle energy and mass loss in erosion by dilute slurries. Wear 1995, 186-187:454-464.
8. Iwai Y., Nambu K. Slurry wear properties of pump lining materials. Wear 1997, 210:211-219.
9. Finnie I. Some reflections on the past and future of erosion. Wear 1995, 186-187:1.
10. Finnie I., Stevick G.R., Ridgely J.R. The influence of impingement angle on the erosion of ductile materials by angular abrasive particles. Wear 1992, 152:91-98.
11. Lopez D., Sanchez C., Toro A. Corrosion-erosion behavior of TiN-coated stainless steels in aqueous slurries. Wear 2005, 258:684-692.
12. Prasad B.K. Effects of alumina particle dispersion on the erosive-corrosive wear response of a zinc-based alloy under changing slurry conditions and distance. Wear 2000, 238:151-159.
13. Fangu Q., Sidky P., Hocking M.G. Erosive wear behavior of aluminium based composites. Mater Des 1997, 18:389-393.
14. Cooper D., Davis F.A., Wood R.J.K. Selection of wear-resistant materials for the petrochemical industry. J Phys D Appl Phys. 1992, 25:195-204.
15. Das S., Saraswathi Y.L., Mondal D.P. Erosive-corrosive wear of aluminum alloy composites: influence of slurry composition and speed. Wear 2006, 261:180-190.
16. Yabuki A., Sugita K., Matsumura M., Hirashima M., Tsunaga M. The anti-slurry erosion properties of polyethylene for sewerage pipe use. Wear 2000, 240:52-58.
17. Shipway P.H., Hutchings I.M. Measurement of coating durability by solid particle erosion. Surf Coat Technol 1995, 71:1-8.
18. Iwai Y., Honda T., Yamada H., Matsubara T., Larsson M., Hogmark S. Evaluation of wear resistance of thin hard coatings by a new solid particle contact test. Wear 2001, 251:861-867.
19. Wood R.J.K., Puget Y., Trethewey K.R., Stokes K. The performance of marine coatings and pipe materials under fluid-borne sand erosion. Wear 1998, 219:46-59.
20. Rajesh J.J., Bijwe J., Tewari U.S., Venkataraman B. Erosive wear behavior of various polyamides. Wear 2001, 249:702-714.
21. Beall G.H., Rittler H.L. Basalt glass-ceramics. Am Ceram Soc Bull 1976, 55:579-582.
22. Yilmaz S., Ozkan O.T., Gunay V. Crystallization kinetics of basalt glass. Ceramic Int 1996, 22:477-481.
23. Znidarsic V., Kolar D. The crystallization of diabase glass. J Mater Sci 1991, 26:2490-2494.
24. Karamanov A., Arrizza L., Ergul S. Sintered material from alkaline basaltic tuffs. J Eur Ceramic Soc 2009, 29:595-601.
25. Standard test method for tensile properties of plastics. American Society for Testing and Materials, ASTM D638-10; 2010.
26. Standard test method for rubber property-durometer hardness. American Society for Testing and Material, ASTM D2240-05; 2010.
27. Mareri P., Bastide S., Binda N., Crespy A. Mechanical behavior of polypropylene composites containing fine mineral filler: effect of filler surface treatment. Compos Sci Technol 1998, 58:747-752.
28. Ren Z., Shanks R.A., Rook T.J. Processing and properties of polypropylene composites with high filler content. Polym Polym Compos 2002, 10:173-183.
29. Zhou R., Lu D.H., Jiang Y.H., Li Q.N. Mechanical properties and erosion wear resistance of polyurethane matrix composites. Wear 2005, 259:676-683.
30. Sari N.Y. Influence of erodent particle types on solid particle erosion of polyphenylene sulphide composite under low particle speed. Polym Compos 2009, 30:1442-1449.