Milling time and BPR dependence on permeability and losses of Ni 0.5Zn0.5Fe2O4 synthesized via mechanical alloying process

Journal of Magnetism and Magnetic Materials

Volumn 323, Issue 11, 2011, Pages 1470-1476

  Ismail, Ismayadi ^a   Hashim, Mansor ^a   Amin Matori, Khamirul ^a   Alias, Rosidah ^b   Hassan, Jumiah ^a  

^a UNIVERSITY PUTRA MALAYSIA   (Malaysia)

^b Telekom Research and Development Sdn Bhd   (Malaysia)

Author keywords

Losses; Mechanical alloying; Permeability; Sintering temperature

Indexed keywords

1.8 GHZ; ALLOYING PROCESS; BALL-TO-POWDER WEIGHT RATIO; FREQUENCY RANGES; IMPEDANCE ANALYZER; MECHANICAL ALLOYING METHOD; MILLING TIME; PERMEABILITY; SEM; SINTERING TEMPERATURE; TEM; XRD;

BALL MILLING; MAGNETIC PROPERTIES; MECHANICAL ALLOYING; MECHANICAL PROPERTIES; METALLURGY; MILLING (MACHINING); SINTERING; ZINC;

MECHANICAL PERMEABILITY;

EID: 79952188150     PISSN: 03048853     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmmm.2011.01.002     Document Type: Article

References (13)

1. 4 powder and its characterization Mater. Lett. 27 1996 293 296 (Pubitemid 126358988)
2. C.Y. Tsay, K.S. Liu, and T.F. Lin Microwave sintering of NiCuZn ferrites and multilayer chip inductors J. Magn. Mater. 209 2000 189 192 (Pubitemid 32211956)
3. A. Globus, and P. Duplex Separation of susceptibility mechanisms for ferrites of low anisotropy IEEE. Trans. Magn. 2 1966 441 445
4. P.J. van der Zaag, J.J.M. Ruigrok, A. Noordermeer, M.H.W.M. van Delden, P.T. Por, M. Th. Rekveldt, D.M. Donnet, and J.N. Chapman The initial permeability of polycrystalline MnZn ferrites: the influence of domain and microstructure J. Appl. Phys. 74 1993 4085 4095
5. J. Topfer, H. Kahnt, P. Nauber, S. Senz, and D. Hesse Microstructural effects in low loss power ferrites J. Eur. Ceram. Soc. 25 2005 3045 3049 (Pubitemid 40829765)
6. K.J. Standley Oxide Magnetic Materials second ed. 1972 Oxford Universities Press Northern Ireland
7. Alex Goldman Handbook of Modern Ferromagnetic Materials 1999 Kluwer Academic Publishers
8. S. Bid, and S.K. Pradhan Preparation of zinc ferrite by high-energy ball-milling and microstructure characterization by Rietvelds analysis Mater. Chem. Phys. 82 2003 27 37
9. 3 J. Eur. Ceram. Soc. 26 2006 141 148 (Pubitemid 41600429)
10. D. Marrero-Lpez, M.C. Martn-Sedeo, J. Pea-Martnez, J.C. Ruiz-Morales, P. Nez, M.A.G. Aranda, and J.R. Ramos-Barrado Evaluation of apatite silicates as solid oxide fuel cell electrolytes J. Power Sources 195 2010 2496 2506
11. C. Suryanarayana Mechanical alloying and milling Progr. Mater. Sci. 46 2001 1 184 (Pubitemid 32071564)
12. S. Li, K. Wang, L. Sun, and Z. Wang A simple model for the refinement of nanocrystalline grain size during ball milling Scr. Metall. Mater. 27 1992 437 442 (Pubitemid 23627181)
13. 4 J. Magn. Magn. Mater. 312 2006 210 219