Behavior and design of axially compressed sheathed wall studs

20th International Specialty Conference on Cold-Formed Steel Structures - Recent Research and Developments in Cold-Formed Steel Design and Construction

Volumn , Issue , 2010, Pages 475-492

  Vieira Jr , L C M ^a   Schafer, B W ^a  

^a JOHNS HOPKINS UNIVERSITY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COLD-FORMED STEEL; DESIGN METHOD; DIRECT STRENGTH METHODS; ELASTIC BUCKLING; LIMIT STATE; NEW APPROACHES; SHEATHED WALLS; TEST RESULTS; WALL STUDS;

BUCKLING; STEEL RESEARCH; STEEL STRUCTURES; STUDS (FASTENERS); STUDS (STRUCTURAL MEMBERS);

STRUCTURAL DESIGN;

EID: 79951878923     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper

References (14)

1. AISI (1962). Light Gage Cold-Formed Steel Design Manual. American Iron and Steel Institute, New York, NY (now Washington, D.C.)
2. AISI (2004) North American Specification for the Design of Cold-Formed Steel Structural Members. American Iron and Steel Inst., Wash., D.C.
3. AISI (2007). North American Standard for Cold-Formed Steel Framing-Wall Stud Design. AISI-S211-07, Am. Iron and Steel Inst., Washington, D.C.
4. AISI-S210 (2010). "North American Standard for Cold-Formed Steel Framing - Floor and Roof System Design." American Iron and Steel Institute, Washington, D.C., ANSI/AISI-S210-10, 28 pp.
5. APA (2004) "Panel Design Specification", APA - The Engineered Wood Association.
6. LaBoube, R.A.; Findlay, P.F. (2007). "Wall Stud-to-Track Gap: Experimental Investigation" Journal of Architectural Engineering, Vol. 13, No.2, June 1, 2007.
7. Li, Z. and Schafer, B.W. (2010) The constrained finite strip method for general end boundary conditions. Structural Stability Research Council - Proceedings of the 2010 Annual Stability Conference, Orlando, FL, USA, 2010; p 573-591
8. Miller, T., Peköz, T. (1994). "Behavior of Gypsum-Sheathed Cold-Formed Steel Wall Studs." ASCE, Journal of Structural Eng. 120 (5) 1644-1650.
9. Schafer, B. W., and Adany, S. (2006), "Buckling analysis of cold-formed steel members using CUFSM: Conventional and constrained finite strip methods." Proc. of the 18th Int'l. Spec. Conf. on Cold-Formed Steel Structures, 39-54.
10. Shifferaw, Y., Vieira Jr, L. C. M., Schafer, B.W. (2009). "Compression Testing of Single Column Studs with Sheathing Configurations" AISI Progress Report. www.ce.jhu.edu/bschafer/sheathedwalls
11. Simaan, A. Peköz, T. (1976). "Diaphragm Braced Members and Design of Wall Studs." ASCE, Journal of the Structural Division, 102 (ST1) 77-92.
12. Vieira Jr, L. C. M., Schafer, B.W. (2009). "Full-scale testing of sheathed cold-formed steel wall stud systems in axial compression" AISI Progress Report. www.ce.jhu.edu/bschafer/sheathedwalls
13. Winter, G. (1960). "Lateral Bracing of Beams and Columns." ASCE Transactions, Paper No. 3044,
14. per footnote "published in 1958 in the Journal of the Structural Division"