Wear and smearing resistance of black iron mixed oxide coated steels

International Journal of Surface Science and Engineering

Volumn 4, Issue 4-6, 2010, Pages 337-359

  Mihailidis, A ^a   Salpistis, C ^a   Panagiotidis, K ^a   Sachanas, C ^a   Gatsios, S ^a   Hoffinger, C ^b   Bakolas, V ^b  

^a ARISTOTLE UNIVERSITY OF THESSALONIKI   (Greece)

^b LuK GmbH and Co oHG   (Germany)

Author keywords

Black iron mixed oxide coating; Bluing; Durotect B; Friction coefficient; Mixed lubrication; Running in; Smearing; Solid contact time percentage; Surface coating; Two discs test rig; Wear rate

Indexed keywords

FRICTION; IRON OXIDES; PROTECTIVE COATINGS; SURFACE ROUGHNESS; WEAR OF MATERIALS;

BLUING; FRICTION COEFFICIENTS; MIXED LUBRICATION; MIXED OXIDE; RUNNING-IN; SMEARING; SOLID CONTACTS; SURFACE COATINGS; TEST RIGS; WEAR RATES;

WEAR RESISTANCE;

EID: 78651532202     PISSN: 1749785X     EISSN: 17497868     Source Type: Journal    
DOI: 10.1504/IJSURFSE.2010.035140     Document Type: Article

References (20)

1. Alanou, M. P., Evans, H. P. and Snidle, R. W. (2004) 'Effect of different surface treatments and coatings on the smearing performance of hardened steel discs at very high sliding speeds', Tribology International, Vol. 37, pp. 93-102.
2. Bakolas, V. and Mihailidis, A. (2004) 'Analysis of rough line contacts operating under mixed elastohydrodynamic lubrication conditions', Lubrication Science, Vol. 16, pp. 153-168.
3. Department of Defence (1957) 'Phosphate and black oxide coating of ferrous metals', Washington, MIL-HDBK-205, MIL-HDBK-205A 1985, USA.
4. DIN 50938 (2000) 'Black oxide treatment of ferrous products'.
5. DIN 51819 (1999) 'Prüfung von Schmierstoffen - Mechanisch-dynamische Prüfung auf dem Wälzlagerschmierstoff-Prüfgerät FE8 - Teil 1: Allgemeine Arbeitsgrundlagen, Teil 2: Verfahren für Schmierfette, einzusetzende Prüflager, Schrägkugellager oder Kegelrollenlager, Teil 3: Verfahren für Schmieröl, einzusetzende Prüflager, Axialzylinderrollenlager'.
6. Forschungsvereinigung Antriebstechnik (1985) 'Referenzöle für Wälz-und Gleitlager-, Zahnradund Kupplungsversuche', Forschungsheft 180.
7. Gold, P. W. and Loos, J. (2002) 'Wear resistance of PVD-coatings in roller bearings', Wear, Vol. 253, pp. 465-472.
8. Habig, H. K. (1989) 'Wear behaviour of surface coatings on steels', Tribology International, Vol. 22, pp. 65-73.
9. Hamrock, J. B., Schmid, R. S. and Jacobson, B. (2004) Fundamentals of Fluid Film Lubrication, 2nd ed., Marcel Dekker, New York.
10. Kalin, M. and Vižintin, J. (2005) 'The tribological performance of DLC-coated gears lubricated with biodegradable oil in various pinion/gear material combinations', Wear, Vol. 259, pp. 1270-1280.
11. Ludema, C. K. (1984) 'A review of smearing and running-in of lubricated surfaces, with asperities and oxides in perspective', Wear, Vol. 100, pp. 315-331.
12. Ludema, K. C. (1996) 'Mechanism-based modelling of friction and wear', Wear, Vol. 200, pp. 1-7.
13. Martins, R., Amaro, R. and Seabra, J. (2008) 'Influence of low friction coatings on the smearing load capacity and efficiency of gears', Tribology International, Vol. 41, pp. 234-243.
14. Martins, R. C., Moura, S. P. and Seabra, J. O. (2006) 'MoS2/Ti low-friction coating for gears', Tribology International, Vol. 39, pp. 1686-1697.
15. Meng, H. C. and Ludema, K. C. (1995) 'Wear models and predictive equations: their form and content', Wear, Vol. 181-183, pp. 443-457.
16. Mihailidis, A, Bakolas, V., Drivakos, N. and Panagiotidis, K. (2002) 'Prediction of the friction coefficient of spur gears', VDI Berichte, Vol. 1665, pp. 705-719.
17. Mihailidis, A., Salpistis, C., Drivakos, N. and Panagiotidis, K. (2003) 'Friction behaviour of FVA reference mineral oils obtained by a newly designed two-disc test rig', Proc. of the 1st Int. Conf. Power Transmissions, pp. 32-37.
18. Salpistis, C., Mihailidis, A., Drivakos, N. and Gatsios, S. (2006) 'Experimentally obtained solid contact time curves as a criterion of the EHL performance of the rough surfaces', Proc. of the 2nd Int. Conf. Power Transmissions, pp. 347-350.
19. Suh, Y. A., Polycarpou, A. A. and Conry, F. T. (2003) 'Detailed surface roughness characterization of engineering surfaces undergoing tribological testing leading to smearing', Wear, Vol. 255, pp. 556-568.
20. Szczerek, M. and Tuszynski, W. (2002) 'A method for testing lubricants under conditions of smearing. Part I presentation of the method', Tribotest Journal, Vol. 8, pp. 273-284. (Pubitemid 34811671)