메뉴 건너뛰기




Volumn 50, Issue 12, 2010, Pages 1097-1114

Identification of tool parallel axis offset through the analysis of the topography of surfaces machined by peripheral milling

Author keywords

Cutter grinding errors; Peripheral milling; Surface topography; Tool parallel axis offset

Indexed keywords

COMPUTATIONAL COSTS; CUTTER GRINDING; CUTTER GRINDING ERRORS; CUTTING EDGES; CUTTING TEST; DIGITAL IMAGE PROCESSING; END MILL; GROOVE WIDTH; MILLED SURFACES; OVERDETERMINED SYSTEMS; PARALLEL AXIS; PERIPHERAL MILLING; TRANSITION BANDS;

EID: 77957934500     PISSN: 08906955     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijmachtools.2010.07.006     Document Type: Article
Times cited : (25)

References (20)
  • 2
    • 0020169224 scopus 로고
    • The prediction of surface accuracy in end milling
    • W.A. Kline, R.E. DeVor, and I.A. Shareef The prediction of surface accuracy in end milling ASME J. Eng. Ind. 104 1982 272 278
    • (1982) ASME J. Eng. Ind. , vol.104 , pp. 272-278
    • Kline, W.A.1    Devor, R.E.2    Shareef, I.A.3
  • 3
    • 0020948036 scopus 로고
    • The effect of runout on cutting geometry and forces in end milling
    • W.A. Kline, and R.E. DeVor The effect of runout on cutting geometry and forces in end milling Int. J. Mach. Tool Des. Res. 23 1983 123 140
    • (1983) Int. J. Mach. Tool Des. Res. , vol.23 , pp. 123-140
    • Kline, W.A.1    Devor, R.E.2
  • 4
    • 58149366492 scopus 로고
    • Computerized predictive cutting models for forces in end-milling including eccentricity effects
    • E.J.A. Armarego, and N.P. Deshpande Computerized predictive cutting models for forces in end-milling including eccentricity effects Ann. CIRP 38 1 1989 45 49
    • (1989) Ann. CIRP , vol.38 , Issue.1 , pp. 45-49
    • Armarego, E.J.A.1    Deshpande, N.P.2
  • 5
    • 0025888129 scopus 로고
    • Computerized end-milling force predictions with cutting models allowing for eccentricity and cutter deflections
    • E.J.A. Armarego, and N.P. Deshpande Computerized end-milling force predictions with cutting models allowing for eccentricity and cutter deflections Ann. CIRP 40 1 1991 25 29
    • (1991) Ann. CIRP , vol.40 , Issue.1 , pp. 25-29
    • Armarego, E.J.A.1    Deshpande, N.P.2
  • 6
    • 0028532934 scopus 로고
    • Milling force convolution modeling for identification of cutter axis offset
    • S.Y. Liang, and J.J. Wang Milling force convolution modeling for identification of cutter axis offset Int. J. Mach. Tools Manuf. 34 8 1994 1177 1190
    • (1994) Int. J. Mach. Tools Manuf. , vol.34 , Issue.8 , pp. 1177-1190
    • Liang, S.Y.1    Wang, J.J.2
  • 7
    • 77957956383 scopus 로고    scopus 로고
    • Determination of constant 3D cutting force coefficients and of runout parameters in end milling
    • W.-S. Yun, D.-W. Cho, and K.F. Ehmann Determination of constant 3D cutting force coefficients and of runout parameters in end milling NAMRC XXVII MR9 1999 9 159
    • (1999) NAMRC XXVII , vol.9 , pp. 9-159
    • Yun, W.-S.1    Cho, D.-W.2    Ehmann, K.F.3
  • 8
    • 70349759310 scopus 로고    scopus 로고
    • New procedures for calibration of instantaneous cutting force coefficients and cutter runout parameters in peripheral milling
    • M. Wan, W.-H. Zhang, J.-W. Dang, and Y. Yang New procedures for calibration of instantaneous cutting force coefficients and cutter runout parameters in peripheral milling Int. J. Mach. Tools Manuf. 49 2009 1144 1151
    • (2009) Int. J. Mach. Tools Manuf. , vol.49 , pp. 1144-1151
    • Wan, M.1    Zhang, W.-H.2    Dang, J.-W.3    Yang, Y.4
  • 9
    • 0037402138 scopus 로고    scopus 로고
    • Identification of cutter offset in end milling without a prior knowledge of cutting coefficients
    • J.-J.J. Wang, and C.M. Zheng Identification of cutter offset in end milling without a prior knowledge of cutting coefficients Int. J. Mach. Tools Manuf. 43 2003 687 697
    • (2003) Int. J. Mach. Tools Manuf. , vol.43 , pp. 687-697
    • Wang, J.-J.J.1    Zheng, C.M.2
  • 10
    • 17444374582 scopus 로고    scopus 로고
    • 3D ball-end milling force model using instantaneous cutting force coefficients
    • J.H. Ko, and D.-W. Cho 3D ball-end milling force model using instantaneous cutting force coefficients Trans. ASME J. Manuf. Sci. Eng. 127 2005 1 9
    • (2005) Trans. ASME J. Manuf. Sci. Eng. , vol.127 , pp. 1-9
    • Ko, J.H.1    Cho, D.-W.2
  • 11
    • 10844278284 scopus 로고    scopus 로고
    • A force-model-based approach to estimating cutter axis offset in ball end milling
    • J.-J.J. Wang, and C.-Y. Huang A force-model-based approach to estimating cutter axis offset in ball end milling Int. J. Adv. Manuf. Technol. 24 2004 910 918
    • (2004) Int. J. Adv. Manuf. Technol. , vol.24 , pp. 910-918
    • Wang, J.-J.J.1    Huang, C.-Y.2
  • 12
    • 34247397947 scopus 로고    scopus 로고
    • Efficient calibration of instantaneous cutting force coefficients and runout parameters for general end mills
    • M. Wan, W.-H. Zhang, G.H. Qin, and G. Tan Efficient calibration of instantaneous cutting force coefficients and runout parameters for general end mills Int. J. Mach. Tools Manuf. 47 2007 1767 1776
    • (2007) Int. J. Mach. Tools Manuf. , vol.47 , pp. 1767-1776
    • Wan, M.1    Zhang, W.-H.2    Qin, G.H.3    Tan, G.4
  • 14
    • 0036280576 scopus 로고    scopus 로고
    • An improved method for cutter runout modeling in the peripheral milling process
    • S. Ranganath, and J.W. Sutherland An improved method for cutter runout modeling in the peripheral milling process Mach. Sci. Technol. 6 1 2002 1 20
    • (2002) Mach. Sci. Technol. , vol.6 , Issue.1 , pp. 1-20
    • Ranganath, S.1    Sutherland, J.W.2
  • 15
    • 0027962275 scopus 로고
    • Vibrations and surface generation in slab milling
    • U. Heisel, and J. Milberg Vibrations and surface generation in slab milling Ann. CIRP 43 1 1994 337 340
    • (1994) Ann. CIRP , vol.43 , Issue.1 , pp. 337-340
    • Heisel, U.1    Milberg, J.2
  • 16
    • 33645068641 scopus 로고    scopus 로고
    • A new method to quantify radial error of a motorized end-milling cutter/spindle system at very high speed rotations
    • W. Nakkiew, C.-W. Lin, and J.F. Tu A new method to quantify radial error of a motorized end-milling cutter/spindle system at very high speed rotations Int. J. Mach. Tools Manuf. 46 2006 877 889
    • (2006) Int. J. Mach. Tools Manuf. , vol.46 , pp. 877-889
    • Nakkiew, W.1    Lin, C.-W.2    Tu, J.F.3
  • 17
    • 70449530416 scopus 로고    scopus 로고
    • Model for the prediction of heterogeneity bands in the topography of surfaces machined by peripheral milling considering tool runout
    • M. Arizmendi, J. Fernndez, A. Gil, and F. Veiga Model for the prediction of heterogeneity bands in the topography of surfaces machined by peripheral milling considering tool runout Int. J. Mach. Tools Manuf. 50 2010 51 64
    • (2010) Int. J. Mach. Tools Manuf. , vol.50 , pp. 51-64
    • Arizmendi, M.1    Fernndez, J.2    Gil, A.3    Veiga, F.4


* 이 정보는 Elsevier사의 SCOPUS DB에서 KISTI가 분석하여 추출한 것입니다.