Analysis of single-grooved slider and journal bearing with partial slip surface

Journal of Tribology

Volumn 132, Issue 1, 2010, Pages 1-7

  Rao, T V V L N ^a  

^a BIRLA INSTITUTE OF TECHNOLOGY AND SCIENCE   (India)

Author keywords

Journal bearing; Partial slip surface; Pressure; Shear stress; Single groove; Slider bearing

Indexed keywords

BEARING SURFACES; INCREASE IN PRESSURE; MAXIMUM PRESSURE; NONDIMENSIONAL; ONE-DIMENSIONAL ANALYSIS; PARTIAL SLIP; PARTIAL SLIP SURFACE; REYNOLDS; SHEAR STRESS DISTRIBUTION; SLIDER BEARINGS; SLIP COEFFICIENTS; SLIP INTERFACE; STEADY STATE; UNIFORM FILMS;

JOURNAL BEARINGS; PRESSURE DISTRIBUTION; REYNOLDS EQUATION; SHEAR STRESS; STRENGTH OF MATERIALS; STRESS CONCENTRATION;

BEARINGS (STRUCTURAL);

EID: 77955255601     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.4000276     Document Type: Article

References (12)

1. Craig, V. S. J., Neto, C., and Williams, D. R. M., 2001, "Shear-Dependent Boundary Slip in an Aqueous Newtonian Liquid," Phys. Rev. Lett., 87(5), p. 054504.
2. Zhu, Y., and Granick, S., 2001, "Rate-Dependent Slip of Newtonian Liquid at Smooth Surfaces," Phys. Rev. Lett., 87(9), p. 096105.
3. Zhu, Y., and Granick, S., 2002, "Limits of Hydrodynamic No-Slip Boundary Condition," Phys. Rev. Lett., 88(10), p. 106102.
4. Spikes, H. A., 2003, "The Half-Wetted Bearing. Part 1: Extended Reynolds Equation," Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 217(1), pp. 1-14.
5. Spikes, H. A., 2003, "The Half-Wetted Bearing. Part 2: Potential Applications in Low Load Contacts," Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 217(1), pp. 15-26.
6. Salant, R. F., and Fortier, A. E., 2004, "Numerical Analysis of a Slider Bearing With a Heterogeneous Slip/No-Slip Surface," STLE Tribol. Trans., 47(3), pp. 328-334.
7. Fortier, A. E., and Salant, R. F., 2005, "Numerical Analysis of a Journal Bearing With a Heterogeneous Slip/No-Slip Surface," ASME J. Tribol., 127(4), pp. 820-825.
8. Wu, C. W., Ma, G. J., Zhou, P., and Wu, C. D., 2006, "Low Friction and High Load Support Capacity of Slider Bearing With a Mixed Slip Surface," ASME J. Tribol., 128(4), pp. 904-907.
9. Fowell, M., Olver, A. V., Gosman, A. D., Spikes, H. A., and Pegg, I., 2007, "Entrainment and Inlet Suction: Two Mechanisms of Hydrodynamic Lubrication in Textured Bearings," ASME J. Tribol., 129(2), pp. 336-347.
10. Tichy, J. A., and Ku, C.-P., 1988, "A Thin Film Flow Rupture Model for Newtonian and Viscoelastic Fluids," ASME J. Tribol., 110(4), pp. 712-717.
11. Huang, P., Li, Z.-h., Meng, Y.-g., and Wen, S.-z., 2002, "Study on Thin Film Lubrication With Second-Order Fluid," ASME J. Tribol., 124(3), pp. 547- 552.
12. Watanabe, K., Yanuar, U., and Udagawa, H., 1999, "Drag Reduction of Newtonian Fluid in a Circular Pipe With a Highly Water-Repellant Wall," J. Fluid Mech., 381, pp. 225-238.