Effect of modification treatment on the microstructure and mechanical properties of Al-0.35%Mg-7.0%Si cast alloy

Materials and Design

Volumn 31, Issue 9, 2010, Pages 4408-4413

  Zhang, X H ^a   Su, G C ^a   Ju, C W ^b   Wang, W C ^a   Yan, W L ^a  

^a GUANGXI UNIVERSITY   (China)

^b Guangxi Institute of Special Equipment Supervision and Inspection   (China)

Author keywords

[No Author keywords available]

Indexed keywords

AL-MG-SI ALLOYS; CAST ALLOYS; EUTECTIC SILICON; FRACTOGRAPHS; INTERGRANULAR FRACTURE; MICROSTRUCTURE AND MECHANICAL PROPERTIES; MIXED MODE FRACTURE; MODIFICATION TREATMENT; PLATE-LIKE STRUCTURE; PRIMARY SILICON; QUASI-CLEAVAGE; ROOM TEMPERATURE; SCANNING ELECTRON MICROSCOPE; SI-PARTICLE; SOLID SOLUTION DENDRITE; TRANSGRANULAR;

ALUMINUM; BARIUM; BARIUM ALLOYS; FRACTURE; MECHANICAL PROPERTIES; SCANNING ELECTRON MICROSCOPY; SILICON; TEXTURES; WEAR RESISTANCE;

SILICON ALLOYS;

EID: 77953541151     PISSN: 02641275     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.matdes.2010.04.032     Document Type: Article

References (17)

1. Choong D.L. Variability in the tensile properties of squeeze-cast Al-Si-Cu-Mg alloy. Mater Sci Eng A 2008, 488:296-302.
2. Geoffroy N., Vittecoq E., Birr A., et al. Fatigue behaviour of an arc welded Al-Si-Mg alloy. Scr Mater 2007, 57:349-352.
3. Shah K.B., Kumar S.D., Dwivedi D.K. Aging temperature and abrasive wear behaviour of cast Al-(4%, 12%, 20%)Si-0.3%Mg alloys. Mater Des 2007, 28:1968-1974.
4. Yao J.Y., Graham D.A., Rinderer B., et al. A TEM study of precipitation in Al-Mg-Si alloys. Micron 2001, 32:865-870.
5. Kori S.A., Murty B.S., Chakraborty M. Development of an efficient grain refiner for Al-7Si alloy and its modification with strontium. Mater Sci Eng A 2000, 283:94-104.
6. Nogita K., Knuutinen A., McDonald S.D., et al. Mechanisms of eutectic solidification in Al-Si alloys modified with Ba, Ca, Y and Yb. J Light Met 2001, 1:219-228.
7. Knuutinen A., Nogita K., McDonald S.D., et al. Modification of Al-Si alloys with Ba, Ca, Y and Yb. J Light Met 2001, 1:229-240.
8. Knuutinen A., Nogita K., McDonald S.D., et al. Porosity formation in aluminium alloy A356 modified with Ba, Ca, Y and Yb. J Light Met 2001, 1:241-249.
9. Hanabe M., Aswath P.B. Synthesis of In-situ reinforced Al composites from Al-Si-Mg-O precursors. Acta Mater 1997, 45:4067-4076.
10. Maeda M., Kiwake T., Shibuya K., et al. Activity of aluminum in molten Ti-Al alloys. Mater Sci Eng A 1997, 239-240:276-280.
11. Wang R.Y., Lu W.H., Hogan L.M. Self-modification in direct electrolytic Al-Si alloys and structural inheritance. Mater Sci Eng A 2003, 348:289-298.
12. Lim Y.P., Shamsuddin S., Abdel M.H., et al. Grain refinement of LM6 Al-Si alloy sand castings to enhance mechanical properties. J Mater Process Technol 2005, 162-163:435-441.
13. Basavakumar K.G., Mukunda P.G., Chakraborty M. Influence of grain refinement and modification on dry sliding wear behavior of Al-7Si and Al-7Si-2.5Cu cast alloys. J Mater Process Technol 2007, 186:236-245.
14. Loue W.R., Suery M. Microstructural evolution evolution during partial remelting of Al-Si7Mg alloys. Mater Sci Eng A 1995, 203:1-13.
15. Qin Q.D., Zhao Y.G., Cong P.J., et al. Functionally graded Mg2 Si/Al composite produced by an electric arc remelting process. J Alloys Compd 2006, 420:121-125.
16. Uematsu Y., Tokaji K., Tozaki Y., et al. Effect of re-filling probe hole on tensile failure and fatigue behavior of friction stir spot welded joints in Al-Mg-Si alloy. Int J Fract 2008, 30:1956-1966.
17. Singh R.K., Singh A.K., Prasad N.E. Texture and mechanical property anisotropy in an Al-Mg-Si-Cu alloy. Mater Sci Eng A 2000, 277:114-122.