Investigation of dry sliding wear properties of boron doped powder metallurgy 316L stainless steel

Materials and Design

Volumn 31, Issue 8, 2010, Pages 3896-3900

  Uzunsoy, D ^a  

^a YILDIZ TECHNICAL UNIVERSITY   (Turkey)

Author keywords

[No Author keywords available]

Indexed keywords

316 L STAINLESS STEEL; BORON ADDITIONS; BORON-DOPED; DELAMINATION WEAR; DISC SPECIMENS; DRY SLIDING WEAR; LIQUID PHASE FORMATION; SURFACE LAYERS; THEORETICAL DENSITY; WEAR BEHAVIORS; WEAR RATES; WEAR TEST; WORN SURFACE; YIELD STRENGTH;

ALUMINUM POWDER METALLURGY; BORON; CORROSION RESISTANT ALLOYS; HARDNESS; MECHANICAL PROPERTIES; SCANNING ELECTRON MICROSCOPY; SINTERING; STEEL METALLURGY; STEEL SHEET; TENSILE STRENGTH; WEAR OF MATERIALS;

STAINLESS STEEL;

EID: 77953292761     PISSN: 02641275     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.matdes.2010.02.053     Document Type: Article

References (17)

1. Coovattanachai O., Tosangthum N., Morakotjinda M., Yotkaew T., Daraphan A., Krataitong R., et al. Performance improvement of P/M 316L by addition of liquid phase forming powder. Mater Sci Eng A 2007, 445-446:440-445.
2. Yang X., Guo S.J. Fe-Mo-B enhanced sintering of P/M 316L stainless steel. J Iron Steel Res Int 2008, 15(1):10-14.
3. Sarasola M., Gomez-Acebo T., Castro F. Liquid generation during sintering of Fe-3.5%Mo powder compacts with elemental boron additions. Acta Mater 2004, 52:4615-4622.
4. Molinari A., Kazior J., Marchetti F., Canteri R., Cristofolini I., Tiziani A. Sintering mechanisms of boron alloyed AISI 316L stainless steel. Powder Metall 1994, 37(2):115-121.
5. Tandon R., German R.M. Sintering and mechanical properties of a boron-doped austenitic stainless steel. Int J Powder Metall 1998, 34:40.
6. Gulsoy H.O., Bilici M.K., Bozkurt Y., Salman S. Enhancing the wear properties of iron based powder metallurgy alloys by boron additions. Mater Design 2007, 28:2255-2259.
7. Bressan J.D., Daros D.P., Sokolowski A., Mesquita R.A., Barbosa C.A. Influence of hardness on the wear resistance of 17-4 PH stainless steel evaluated by the pin-on-disc testing. J Mater Process Technol 2008, 205:353-359.
8. Uzunsoy D, Yeprem HA. Investigation of microstructural evolution and properties of boron doped P/M 316L. In: Proc. world congress on powder metallurgy & particulate materials. Washington, USA; 2008. p. 5-111-7.
9. Uzunsoy D., Yeprem H.A. Characterization of boron doped 316L powder metallurgy (PM) stainless steel. Mater Test (Materialprüfung) 2008, 50(9):517-520.
10. Bollina R. In situ evaluation of supersolidus liquid phase sintering phenomena of stainless steel 316L densification and distortion. PhD thesis, Pennsylvania State University, University Park, PA; 2005.
11. Bakan H.I., Heaney D., German R.M. Effect of nickel boride and boron additions on sintering characteristics of injection moulded 316L powder using water soluble binder system. Powder Metal 2001, 44(3):235-242.
12. Narasimhan KS, Semel FJ. Sinteri{dotless}ng of powder premixes - a brief overview. Powder metallurgy world congress & exhibition. Colorada, USA; 2007. p. 05-01-24.
13. Rosso M. Contribution to study and development of PM stainless steels with improved properties. J Achieve Mater Manuf Eng 2007, 24(1):178-187.
14. Gulsoy H.O. Dry sliding wear in injection molded 17-4 PH stainless steel powder with nickel boride additions. Wear 2007, 262:491-497.
15. Kanchanomai C., Saengwichian B., Manonukul A. Delamination wear of metal injection moulded 316L stainless steel. Wear 2009, 9-10:1665-1672.
16. Molinari A., Straffelini G., Campestrini P. Influence of microstructure on impact and wear behaviour of sintered Cr and Mo steel. Powder Metall 1999, 42:42.
17. Becker BS, Bolton JD, Eagles AM. Sintering of 316L stainless steels to high density via the addition of chromium-molybdenum dibromide powders. Part 1: sintering performance and mechanical properties. In: Proc instn mech engrs, vol. 214(L); 2000. p. 139-52.