Effects of temperature on tensile and impact behavior of dissimilar welds of rotor steels

Materials and Design

Volumn 31, Issue 7, 2010, Pages 3346-3352

  Zhu, Ming Liang ^a   Xuan, Fu Zhen ^a  

^a EAST CHINA UNIVERSITY OF SCIENCE AND TECHNOLOGY   (China)

Author keywords

Dissimilar welding; Rotor steels; Temperature; Tensile

Indexed keywords

BASE METALS; DISSIMILAR WELD; DISSIMILAR WELD JOINT; DISSIMILAR WELDING; EFFECTS OF TEMPERATURE; FRACTURE LOCATION; FRACTURE SURFACES; FRACTURE ZONE; IMPACT BEHAVIOR; IMPACT TOUGHNESS; INHOMOGENEOUS MICROSTRUCTURE; INTERMEDIATE PRESSURES; MULTILAYER WELDING; QUASI-CLEAVAGE; TESTING TEMPERATURE; THREE ZONES; WELD METAL; WELDING JOINTS;

FRACTURE TESTING; METAL TESTING; PLASTICITY TESTING; SURFACE TESTING; TENSILE STRENGTH; WELDING; WELDS;

DUCTILE FRACTURE;

EID: 77952744367     PISSN: 02641275     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.matdes.2010.01.055     Document Type: Article

References (27)

1. Naffakh H., Shamanian M., Ashrafizadeh F. Dissimilar welding of AISI 310 austenitic stainless steel to nickel-based alloy Inconel 657. J Mater Process Tech 2009, 209(7):3628-3639.
2. Song J., Lin S., Yang C., Ma G., Liu H. Spreading behavior and microstructure characteristics of dissimilar metals TIG welding-brazing of aluminum alloy to stainless steel. Mater Sci Eng A 2009, 509(1-2):31-40.
3. Kong T., Chan L., Lee T. Experimental study of effects of process parameters in forge-welding bimetallic materials: AISI 316l stainless steel and 6063 aluminium alloy. Strain 2009, 45(4):373-379.
4. Taban E., Deleu E., Dhooge A., Kalue E. Evaluation of dissimilar welds between ferritic stainless steel modified 12% Cr and carbon steel s355. Weld J 2008, 87(12):291S-297S.
5. Chuaiphan W, Chandra-ambhorn S, Sornil B, Bleck W. Microstructure, mechanical and corrosion behaviour of dissimilar weldments between AISI 304 stainless steels and AISI 1020 carbon steels produced by gas tungsten arc welding using different consumables. In: Shivani B, Clarke R, Duflou J, Merklein M, Micari F, Griffiths J, editors. 13th International conference on sheet metal, vols. 410-411. Birmingham: Trans Tech Publications Ltd.; 2009. p. 533-41.
6. Kostka A., Coelho R., Santos J.D., Pyzalla A. Microstructure of friction stir welding of aluminium alloy to magnesium alloy. Scripta Mater 2009, 60(11):953-956.
7. Leitao C., Emilio B., Chaparro B., Rodrigues D. Formability of similar and dissimilar friction stir welded AA 5182-H111 and AA 6016-T4 tailored blanks. Mater Des 2009, 30(8):3235-3242.
8. Kim N., Kim B., An Y., Jung B., Song S., Kang C. The effect of material arrangement on mechanical properties in Friction Stir Welded dissimilar A5052/A5J32 aluminum alloys. Met Mater Inter 2009, 15(4):671-675.
9. Kang H.T. Fatigue prediction of spot welded joints using equivalent structural stress. Mater Des 2007, 28(3):837-843.
10. Xuan F.Z., Wang Z.F., Tu S.T. Creep finite element simulation of multilayered system with interfacial cracks. Mater Des 2009, 30(3):563-569.
11. Ma T.J., Li Y.Y., Yang S.Y. Impact toughness and fracture analysis of linear friction welded Ti-6Al-4V alloy joints. Mater Des 2009, 30(6):2128-2132.
12. Kim Y.J., Schwalbe K.H. Mismatch effect on plastic yield loads in idealised weldments II. Heat affected zone cracks. Eng Fract Mech 2001, 68(2):183-199.
13. Xuan F.Z., Tu S.T., Wang Z.D. Time-dependent fracture and defect assessment of welded structures at high temperature. J Pre Ves Technol 2006, 128(4):556-565.
14. Jiang W.C., Gong J.M., Tu S.D., Fan Q.S. A comparison of brazed residual stress in plate-fin structure made of different stainless steel. Mater Des 2009, 30(1):23-27.
15. Shige T., Itou S., Magoshi R., Ihimura T., Kondou Y. Development of large-capacity, highly efficient welded rotor for steam turbines. Tech Rev 2001, 38(1):6-11.
16. Welding metallurgy 2003, John Wiley & Sons, Hoboken, (NJ). S. Kou (Ed.).
17. Murugan S., Kumar P., Raj B., Bose M.S.C. Temperature distribution during multipass welding of plates. Int J Pres Ves Pip 1998, 75(12):891-905.
18. Sattari-Far I., Farahani M. Effect of the weld groove shape and pass number on residual stresses in butt-welded pipes. Int J Pres Ves Pip 2009, 86(11):723-731.
19. El-Banna E.M., Nageda M.S., El-Saadat M.M.A. Study of restoration by welding of pearlitic ductile cast iron. Mater Lett 2000, 42(5):311-320.
20. Furuya H., Aihara S., Morita K. A new proposal of HAZ toughness evaluation method-Part 1: HAZ toughness of structural steel in multilayer and single-layer weld joints. Weld J 2007, 86(1):1S-8S.
21. Cardoso P.H.S., Kwietniewski C., Porto J.P., Reguly A., Strohaecker T.R. The influence of delta ferrite in the AISI 416 stainless steel hot workability. Mater Sci Eng A 2003, 351(1-2):1-8.
22. Silva C.C., Miranda HCd., Sant'Ana HBd, Farias J.P. Microstructure, hardness and petroleum corrosion evaluation of 316L/AWS E309MoL-16 weld metal. Mater Charact 2009, 60(4):346-352.
23. Schäfer L. Influence of delta ferrite and dendritic carbides on the impact and tensile properties of a martensitic chromium steel. J Nucl Mater 1998, 258-263:1336-1339.
24. Li D., Lin D., Liu Y. Effect of temperature on the tensile properties and dislocation structures of FeAl alloys. Mater Sci Eng A 1998, 249(1-2):206-216.
25. Liu H., Fujii H., Maeda M., Nogi K. Tensile fracture location characterizations of friction stir welded joints of different aluminum alloys. J Mater Sci Technol 2004, 20(1):103-105.
26. Liu H.J., Fujii H., Maeda M., Nogi K. Tensile properties and fracture locations of friction-stir-welded joints of 2017-T351 aluminum alloy. J Mater Process Technol 2003, 142(3):692-696.
27. Smith G.E., Crocker A.G., Moskovic R., Flewitt P.E.J. Competing fracture mechanisms in the brittle-to-ductile transition region of ferritic steels. Mater Sci Eng A 2004, 387-389:367-371.