Polypropylene combustion in a fluidized bed combustor

Energy Sources, Part A: Recovery, Utilization and Environmental Effects

Volumn 32, Issue 12, 2010, Pages 1121-1129

  Han, J ^a   Shimizu, T ^c   Wataru, M ^b   Kim, H ^b,d   Wang, G ^a  

^a WUHAN UNIVERSITY OF SCIENCE AND TECHNOLOGY   (China)

^b TOYOHASHI UNIVERSITY OF TECHNOLOGY   (Japan)

^c NIIGATA UNIVERSITY   (Japan)

^d Seoul National University of Science and Technology   (South Korea)

Author keywords

Combustion; Fluidized bed combustor; Polypropylene

Indexed keywords

BED MATERIALS; COMBUSTION EFFICIENCIES; COMBUSTION PRO-CESS; ENERGY RECOVERY; ENERGY RECYCLE; EXCESS AIR; HIGH-CALORIFIC-VALUE; POROUS ALUMINA; SEMI-PILOT SCALE; TEMPERATURE INCREASE; WASTE PLASTIC;

ELASTOMERS; ENERGY CONVERSION; FLUIDIZATION; FLUIDIZED BED COMBUSTORS; FLUIDIZED BEDS; PLASTIC PRODUCTS; PLASTICITY; RECYCLING; SMOKE; THERMOPLASTICS; WASTE INCINERATION;

FLUIDIZED BED COMBUSTION;

EID: 77951181505     PISSN: 15567036     EISSN: 15567230     Source Type: Journal    
DOI: 10.1080/15567030802612499     Document Type: Article

References (15)

1. Boavida, D., Gulyurtlu, I., and Cabrita, I. 2003. Co-combustion of coal and non-recyclable paper and plastic waste in a fluidised bed reactor. Fuel 82:1931-1938.
2. Jin, Y. Q., Zhou, J. Q., Yan, J. H., Yong, C., Liu, X., Mi, M. J., and Cen, K. F. 2002. Experimental study of waste plastics incineration and pollutants emission in a laboratory scale fluidized bed combustors. Power Eng. 22:1724-1728.
3. Khalfi, A., Delobel, R., and Delfosse, L. 2000. Correlation of CO and PAH emissions during laboratory-scale incineration of wood waste furnitures. J. Anal. Appl. Pyrol. 56:243-262.
4. Lee, C. C., and Huffman, G. L. 1989. Incineration of solid waste. Environ. Progr. 8:143-151.
5. Quaak, P., Knoef, H., and Stassen, H. E. 2004. Energy from Biomass: A Review of Combustion and Gasification Technologies. Washington, D.C.: World Bank Publication.
6. Saeed, L. 2002. Experimental assessment of two-stage combustion of high PVC solid waste with HCl recovery. Helsinki, Finland: Helsinki University of Technology.
7. Shimizu, T., Franke, H. J., Satoko, H., Yasuo, T., and Kazuaki, Y. 2001a. Porous bed material-An approach to reduce both unburnt gas emission and NOx emission from a bubbling fluidized bed waste incinerator. J. Japan Inst. Energy 80:333-342.
8. Shimizu, T., Franke, H. J., Satoko, H., Yasuo, T., and Kazuaki, Y. 2001b. Reduction of dioxins emission from a bubbling fluidized bed waste incinerator by use of porous bed material. J. Japan Inst. Energy 80:1060-1063. (Pubitemid 34103806)
9. Shimizu, T., Han, J., Choi, S., Kim, L. Y., and Kim, H. J. 2006. Fluidized-bed combustion characteristics of cedar pellets by using an alternative bed material. Energy & Fuel 20:2737-2742.
10. Wagner, J. P., and Caraballo, S. A. 1997. Toxic species emissions from controlled combustion of selected rubber and plastic consumer products. Polym. Plast. Tech. Eng. 36:189-224.
11. Wang, J. L., Richter, H., Howard, J. B., and Carlson, J. 2001. Polycyclic aromatic hydrocarbon and particulate emissions from two-stage combustion of polystyrene: The effect of the primary furnace temperature. Environ. Sci. & Tech. 35:3541-3552.
12. Wang, Z. R., Howard, J. B., Jordan, J., Carlson, J., and Levendis, Y. A. Laboratory investigation of the products of the incomplete combustion of waste plastics and techniques for their minimization. Indus. & Eng. Chem. Res. 43:2873-2886.
13. Williams, P. T., and Slaney, E. 2007. Analysis of products from the pyrolysis and liquefaction of single plastics and waste plastic mixtures. Resour., Conserv. & Recyc. 51:754-769.
14. You, X. F., Li, X. D., Yan, J. H., Ni, M. J., and Cen, K. F. 2003. PAHs emission from fluidized bed incineration of three kinds of plastics. J. Combus. Sci. & Tech. 9:376-380.
15. Zhang, H. U., Zhu, J. F., and Okuwaki, A. 2007. Prospect and current status of recycling waste plastics and technology for converting them into oil in China. Resour., Conserv. & Recyc. 50:231-239.