Self-reinforced high-density polyethylene prepared by low frequency vibration-assisted injection molding. II: Microstructure investigation

Journal of Macromolecular Science, Part B: Physics

Volumn 49, Issue 2, 2010, Pages 242-249

  Youbing, Li ^a,b   Kaizhi, Shen ^b  

^a CHONGQING UNIVERSITY OF TECHNOLOGY   (China)

^b SICHUAN UNIVERSITY   (China)

Author keywords

HDPE; Injection molding; Melt vibration; Morphology; Shish kebab

Indexed keywords

CONVENTIONAL INJECTION MOLDING; CORE REGION; CRYSTALLINITIES; LOW-FREQUENCY VIBRATION; MELT VIBRATION; MICROSTRUCTURE INVESTIGATIONS; MOLECULAR ALIGNMENT; SELF REINFORCED; SELF-REINFORCEMENT; SEM; SEM MICROGRAPHS; SHISH-KEBAB MORPHOLOGY; SHISH-KEBABS; WIDE-ANGLE X-RAY DIFFRACTION;

DIFFERENTIAL SCANNING CALORIMETRY; MICROSTRUCTURE; MOLECULAR ORIENTATION; MORPHOLOGY; PLASTIC MOLDS; REINFORCEMENT; SCANNING ELECTRON MICROSCOPY; THERMOPLASTICS; X RAY DIFFRACTION;

INJECTION MOLDING;

EID: 77951107002     PISSN: 00222348     EISSN: 1525609X     Source Type: Journal    
DOI: 10.1080/00222340903328856     Document Type: Article

References (16)

1. Kubat, J.; Manson, J.A. High modulus/high strength polyethylene obtained by high-pressure injection molding. Polym. Eng. Sci. 1983, 23(16), 869-876.
2. Kubat, J.; Manson, J.A.; Rigdahl, M. Influence of mold design on the mechanical properties of high-pressure injection-molded polyethylene. Polym. Eng. Sci. 1983, 23(16), 877-882.
3. Bodizar, A.; Manson, J.A.; Rigdahl, M. Influence of mold filling rate and gate geometry on the modulus of high pressure injection-molded polyethylene. J. Appl. Polym. Sci. 1990, 39(1), 63-71.
4. Bayer, R.K.; Zachmann, H.G.; Balta Calleja, F.J.; Umbach, H. Properties of elongational flow injection-molded polyethylene. Part 1: influence of mold geometry. Polym. Eng. Sci. 1989, 29(3), 187-192.
5. Lopez Cabarcos, E.; Bayer, R.K.; Zachmann, H.G.; Balta Calleja, F.J.; Meins, W. Properties of elongational flow injection-molded polyethylene part 2: influence of processing parameters. Polym. Eng. Sci. 1989, 29(3), 193-201.
6. Bayer, R.K.; Balta Calleja, F.J.; Lopez Cabarcos, E.; Zachmann, H.G.; Paulsen, A.; Bruning, F.; Meins, W. Properties of elongational flow injection moulded polyethylene. J. Mater. Sci. 1989, 24(7), 2643-2652.
7. Allan, P.S.; Bevis, M.J. Multiple live feed injection moulding. Plast. Rubb. Process Appl. 1987, 7(1), 3-10.
8. Guan, Q.; Zhu, X.; Chiu, D.; Shen, K.; Lai, F.S.; Mccarthy, S.P. Self-reinforcement of polypropylene by oscillating packing injection molding under low pressure. J. Appl. Polym. Sci. 1995, 62(5), 755-762.
9. Kalay, G.; Sousa, R.A.; Reis, R.L.; Cunha,A.M.; Bevis, M.J. The enhancement of the mechanical properties of a high-density polyethylene. J. Appl. Polym. Sci. 1999, 73(12), 2473-2483.
10. Guan, Q.; Kaizhi, S.; Jiliang, J.; Jumu, Z. Structure and properties of self-reinforced polyethylene prepared by oscillating packing injection molding under low pressure. J. Appl. Polym. Sci. 1995, 55(13), 1797-1804.
11. Li, Y. Self-reinforced high-density polyethylene prepared by low frequency vibration-assisted injection molding.1. Processing conditions and physical properties. J. Macromol. Sci. Part B Phys. 2009, 48(4), 736-744.
12. Olley, R.H.; Hodge, A.M.; Bassett, D.C.; Thomson, J.J. A permanganic etchant for polyolefines. J. Polym. Sci. Polym. Phys. Ed. 1979, 17(4), 627-643.
13. Wunderlich, B. Thermal analysis. New York: Academic Press, 1990.
14. Sousa, R.A.; Reis, R.L.; Cunha, A.M.; Bevis, M.J. Structural development of HDPE in injection molding. J. Appl. Polym. Sci. 2003, 89(8), 2079-2087.
15. Pornnimit, B.; Ehrenstein, G.W. Zur Eigenverstärkung von Polyethylen beim Extrudieren Kunststoffe. Kunststoffe 1989, 79(7), 631-636.
16. Godinho, J.S.; Cunha, A.; Crawford, R.J. Influence of thermomechanical conditions on structure development and mechanical properties of polyethylene mouldings produced using different moulding methods. Plast. Rubb. Copos. 2000, 29(7), 316-328.