Studies on aluminum - Fly-ash composite produced by impeller mixing

Journal of Reinforced Plastics and Composites

Volumn 29, Issue 1, 2010, Pages 144-148

  Sarkar, S ^a   Sen, S ^a   Mishra, S C ^a   Kudelwar, M K ^b   Mohan, S ^b  

^a NATIONAL INSTITUTE OF TECHNOLOGY   (India)

^b BANARAS HINDU UNIVERSITY   (India)

Author keywords

Applied load and sliding velocity.; Industrial waste; Particulate composite

Indexed keywords

IMPELLER MIXING; LIQUID METALLURGIES; MATRIX; PARTICULATE COMPOSITES; REINFORCING PHASE; SLIDING VELOCITIES; WEAR PROPERTIES; WET CHEMICAL ANALYSIS; XRD;

IMAGE ANALYSIS; MAGNESIUM; MECHANICAL PROPERTIES;

ASHES;

EID: 77649261253     PISSN: 07316844     EISSN: 15307964     Source Type: Journal    
DOI: 10.1177/0731684408096428     Document Type: Article

References (15)

1. Akbulut, M., Darman, F. and Yilmaz, (1998). Dry Wear and Friction Properties of δ-Al2O3 Short Fiber Reinforced Al-Si (LM 13) Alloy Metal Matrix Composites, Wear, 215: 170-179.
2. Skolianos, S. and Kattamis, T.Z. (1993). Tribological Properties of SiCp-reinforced Al-4.5% Cu-1.5% Mg Alloy Composites, Mater. Sci. Engg, A163: 107-113.
3. Jiang, J.Q., Tan, R.S. and Ma, A.B. (1996). Dry Sliding Wear Behaviour of Al2O3-Al Composites produced by Centrifugal Force Infiltration, Mater. Sci. Technol., 12: 483-488.
4. Surappa, M.K. and Prasad, S.C. (1982). Wear and Abrasion of Cast Al-Alumina Particle Composites, Wear, 77: 295-302.
5. Kosel, T.H. and Fiore, N.F. (1981). Abrasive Wear in Multiphase Microstructures, J. Mater. Energy Sys., 3: 7-27.
6. Baker, T.N. and Gürcan, A.B. (1995). Wear behaviour of AA6061 Aluminium Alloy and its Composites, Wear, 188: 185-191.
7. Axen, N. and Jacobson, S. (1994). Transitions in the Abrasive Wear Resistance of Fibre- and Particle-reinforced Aluminium, Wear, 178: 1-7.
8. Sheu, S.-Y. and Lin, S.-J. (1996). Particle Size Effects on the Abrasive Wear of 20 vol% SiCp/7075Al Composites, Scr. Mater., 35: 1271-1276.
9. Rohatgi, P.K., Weiss, D. and Gupta, N. (2006). Applications of Fly Ash in Synthesizing Low-cost MMCs for Automotive and other Applications, JOM, 58: 71-76.
10. Rohatgi, P.K. and Guo, R.Q. (1997). Opportunities of Using Fly Ash Particles for Synthesis of Composites, Proceedings of the 59th Annual American Power Conference, Chicago, pp. 828-833.
11. Koczak, M.J. and Prem Kumar, M.K. (1993). Emerging Technologies for the in situ Production of MMCs, JOM, 45: 44-48.
12. Maity, P.C., Chakraborty, P.N. and Panigrahi, S.C. (1994). Preparation of Al-MgAl2O4-MgO in situ Particle-composites by Addition of MnO2 Particles to Molten Al-2 wt% Mg Alloys, Mat. Letters, 20: 93-97.
13. Kuruvilla, A.K., Prasad, K.S., Vanu Prasad, V.V. and Mahajan, R. (1990). Microstructure-property Correlation in Al/TiB2 (XD) Composites, Scripta Metall., 24: 873-878.
14. Maity, P.C., Chakraborty, P.N. and Panigrahi, S.C. (1993). Preparation of Aluminium-alumina in situ Particle Composite by Addition of Titania to Aluminium Melt, Scripta Metall. Mater., 28: 549-552.
15. Sahoo, P. and Koczak, M.J. (1991). Analysis of in situ Formation of Titanium Carbide in Aluminum Alloys, Mat. Sci. Engg, A144: 37-44.