Finite element analysis of the effect of coefficient of friction on the drawability

Tribology International

Volumn 43, Issue 5-6, 2010, Pages 1132-1137

  Chandra Mohan Reddy, G ^a   Ravindra Reddy, P V R ^a   Janardhan Reddy, T A ^b  

^a CHAITANYA BHARATHI INSTITUTE OF TECHNOLOGY   (India)

^b OSMANIA UNIVERSITY   (India)

Author keywords

Deep drawing; Limit drawing ratio; Limit strains

Indexed keywords

ANALYTICAL EQUATIONS; COEFFICIENT OF FRICTIONS; DRAWABILITY; EXPERIMENTAL SETUP; EXPLICIT FINITE ELEMENT CODES; FINITE ELEMENT ANALYSIS; FORMING CONDITIONS; LIMIT DRAWING RATIO; LIMIT STRAINS; LS-DYNA; MATERIAL PROPERTY; PUNCH CORNER; VORTEX THEORY;

FRICTION; TRIBOLOGY;

DEEP DRAWING;

EID: 77549087058     PISSN: 0301679X     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.triboint.2009.12.024     Document Type: Article

References (38)

1. Wagoner R. Development of OSU formability test and OSU friction test. J Mater Process Technol 45 (1994) 13-18
2. Paunoiu V, Nicoar D, Maria Cantera Lopez A, Higuera PA. Experimental researches regarding the forming limit curves using reduced scale samples. The annals "dunarea de jos university of Galati Fascicle V, technologies in machine building, ISSN 1221-4566, 2005: 60-4.
3. Andre Westeneng. Modeling of contact and friction in deep drawing processes. Research project report, University of Twente, 2001.
4. Jurkovic M., et al. The Tribological state test in metal forming processes using experiment and modeling. J Achiev Mater Manuf Eng 18 (2006) 383-386
5. Davis JR. Concise metals engineering data book. ASM publication; 2007. Table 14.1.
6. Keeler S.P., and Backofen W.A. Plastic instability and fracture in sheets stretched over rigid punches. ASM Trans Quart 56 (1964) 25
7. Goodwin GM. Application of strain analysis to sheet metal forming problems in the press shop. SAE paper no. 680093, 1968.
8. Keeler S.P. Determination of forming limits in automotive stampings. Sheet Met Ind 42 (1965) 683-691
9. Goodwin GM. Application of strain analysis to sheet metal forming problems in the press shop. SAE Automative Engineering Congress, SAE paper no. 680093, Detroit, MI, USA, 1968
10. Boudeau N., and Gelin J.C. Finite element simulation of the ductile fracture in 3-D sheet metal forming process. J Mater Process Technol 32 (1992) 521-530
11. Gronostajski J., and Zimniak Z. A few methods of analytical calculation of forming-limit curves. J Mater Process Technol 55 (1995) 213-217
12. Atkins A.G. Fracture in forming. J Mater Process Technol 56 (1996) 609-618
13. Hecker SS. A simple forming limit curve technique and results on aluminum alloys, sheet metal forming and formability. In: Proceedings of the 7th biennial congress of the international deep drawing research group, Amsterdam, 1972, p. 5.1-5.8.
14. Marciniak Z., and Kuczynski K. Limit strains in the processes of stretch-forming sheet metal. Int J Mech Sci 9 (1967) 609
15. Graf A., and Hosford W.F. Calculations of forming limit diagrams for changing strain paths. Metall Trans 24 (1993) 2497
16. Graf A., and Hosford W.F. Effect of changing strain paths on forming limit diagrams of Al 2008-T4. Metall Trans 24 (1993) 2503
17. Graf A., and Hosford W.F. The influence of strain path changes on forming limit diagrams of Al 6111-T4. Int J Mech Sci 36 (1994) 897
18. Hance BM, Foley RP and Matlock DK. Effects of strain path on formability and microstructual evolution in low-carbon sheet steels, SAE paper 970155, 1997
19. Soren S, Rice JR. Localised necking in thin sheets. J Mech Phys Solids 23;421-41.
20. Zhu X., Weinmann K., and Chandra A. A unified bifurcation analysis of sheet metal forming limits. J Eng Mater Technol 123 (2001) 329-333
21. Jie M., Cheng C.H., Chan L.C., Chow C.L., and Tang C.Y. Experimental and theoretical analysis on formability of aluminum tailor welded blanks. J Eng Mater Technol 129 (2007) 151-158
22. Makinouchi A., Teodosiu C., and Nakagawa T. Advance in FEM simulation and its related technologies in sheet metal forming. Ann CIRP 47/2/1998 (1998) 641-649
23. Fratini L., Locasto S., and Mcari F. Numerical analysis and experimental tests of deep drawing sequences. IMech (1995) 61-66
24. Wang X., and Cao J. On the prediction of side wall wrinkling in sheet metal forming processes. Int J Mech Sci 42 (2000) 2369-2394
25. Jamal Hematian. Finite element modeling of wrinkling during deep drawing of pressure vessel end closures (PVECs), M.S. Thesis, Queen's University Kingston, Ontario, Canada, January 2000.
26. Abedrabbo N. Forming of aluminum alloys at elevated temperatures-part1: material characterization. Int J Plasticity 22 (2006) 314-341
27. Garcia J. The need for computational model validation. Exp Tech 25 2 (2001) 31-33
28. Hills R.G., and Trucano T.G. Statistical validation of engineering and scientific models: background. SAND99 (1999) 1256
29. Huang A., Lowe A., and Cardew-Hall M.J. Experimental validation of sheet thickness optimization for superplastic forming of engineering structures. J Mater Process Technol 112 (2001) 136-143
30. Geng L., and Wagoner R.H. Role of plastic anisotropy and its evolution on spring back. Int J Mech Sci 44 (2002) 123-148
31. Livatyali H., Wu H.C., and Altan T. Prediction and elimination of spring back in straight flanging using computer aided design methods 2. FEM predictions and tool design. J Mater Process Technol 120 (2002) 348-354
32. Livatyali H., and Altan T. Prediction and elimination of springback in straight flanging using computer aided design methods. 1. Experimental investigations. J Mater Process Technol 117 (2001) 262-268
33. Thaweepat B., and Jian C. Approaches for model validation: methodology and illustration on a sheet metal flanging process. J Manuf Sci Eng 128 (2006) 589-597
34. Erman Tekkaya A. A guide for validation of fe-simulations in bulk metal forming. Arabian J Sci Eng 30 (2005) 113-136
35. Viorel Paunoiu, Dumitru Nicoara, Ana Maria Cantera Lopez, Pedro Arroyo Higuera. Experimental researches regarding the forming limit curves using reduced scale samples. The annals "dunnarea De Jos" university of Galati I Fascicle V, Technologies in Machine Building, ISSN 1221-4566, 2005;60-4.
36. Viorel Paunoiu, Dumitru Nicoara, Ana Maria Cantera Lopez, Pedro Arroyo Higuera. Numerical simulation of forming limit curves using reduced scale samples. The annals dunnarea De Jos university of Galati I Fascicle V, Technologies in Machine Building, ISSN 1221-4566, 2005; 60-4.
37. Phillip JR. Taguchi techniques for quality engineering. 2nd ed. (1996), McGraw-Hill International, New York
38. Koheran A.S., et al. Forming limits of austenitic stainless steels. Computer Methods in Material Science 6 3-4 (2006) 178-187