Instrumented indentation and scratch testing evaluation of tribological properties of tin-based bearing materials

Materials and Design

Volumn 31, Issue 6, 2010, Pages 2707-2715

  Bora, Mustafa Özgür ^a   Coban, Onur ^a   Sinmazcelik, Tamer ^a,b   Günay, Volkan ^b   Zeren, Muzaffer ^a  

^a KOCAELI UNIVERSITY   (Turkey)

^b MATERIALS INSTITUTE   (Turkey)

Author keywords

A. Non ferros metals and alloys; E. Wear; I. Abrasion

Indexed keywords

A. NON-FERROS METALS AND ALLOYS; BEARING MATERIALS; COEFFICIENT OF FRICTIONS; DEFORMATION MECHANISM; FRICTION COEFFICIENTS; HARDNESS VALUES; INSTRUMENTED INDENTATION; MARTENS HARDNESS; METALS AND ALLOYS; NORMAL LOADS; SCANNING ELECTRON MICROSCOPIC; SCRATCH HARDNESS; SCRATCH TEST; SCRATCH TESTING; SCRATCH VELOCITY; SCRATCH WIDTH; TRIBOLOGICAL BEHAVIORS; TRIBOLOGICAL PROPERTIES;

ABRASION; DEFORMATION; FRICTION; HARDNESS; HARDNESS TESTING; MATERIALS; METAL RECOVERY; METALLURGY; OPTICAL MICROSCOPY; TESTING; TIN; TITANIUM COMPOUNDS; TRIBOLOGY;

MATERIALS TESTING;

EID: 77149179368     PISSN: 02641275     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.matdes.2010.01.033     Document Type: Article

References (31)

1. Lepper K., James M., Chashechkina J., and Rigney D.A. Sliding behaviour of selected aluminum alloys. Wear 203-204 (1997) 46-56
2. Booser E., and Khonsari M. Applied tribology bearing design and lubrication (2001), Wiley, NY
3. Iliev H. Failure analysis of hydro-generator thrust bearing. Wear 225-229 (1999) 913-917
4. Tamura K., Ishihara S., Goshima T., and Tachi Y. Effect of cyclic load and sliding speed on sliding wear characteristics of a bearing lined with WJ7 white metal. Proc Inst Mech Eng Part J, J Eng Tribol 218 (2004) 23-31
5. Kong X.L., Liu Y.B., and Qiao L.J. Dry sliding tribological behaviors of nanocrystalline Cu-Zn surface layer after annealing in air. Wear 256 (2004) 747-753
6. Barykin N.P., Sadykov F.A., and Aslanian I.R. Wear and failure of babbit bushes in steam turbine sliding bearings. J Mater Eng Perform 9 1 (2000) 110-115
7. Massalski T.B. Binary alloy phase diagrams (1982), American Society for Metals, Metals Park, (OH)
8. Matucha K.H. Material science and technology. Structure and properties of nonferrous alloys vol. 8 (1996), VCH, New York
9. Feyzullahoglu E., Zeren A., and Zeren M. Tribological behaviour of tin-based materials and brass in oil lubricated conditions. Mater Des 29 (2008) 714-720
10. Zeren A., Feyzullahoglu E., and Zeren M. A study on tribological behaviour of tin-based bearing material in dry sliding. Mater Des 28 (2007) 318-323
11. Zeren A. Embeddability behaviour of tin-based bearing material in dry sliding. Mater Des 28 (2007) 2344-2350
12. Feld H., and Walter P. Contribution to the understanding of mineral hard metal abrasive wear. Powder Metal Int 7 (1975) 188-190
13. Wayne S., Baldoni J., and Buljian S. Abrasion and erosion of WC-Co with controlled microstructures. Tribol Trans 33 (1990) 611-617
14. O'Quigley D.G.F., Luyckx S., and James M.N. An empirical ranking of a wide range of WC-Co grades in terms of their abrasion resistance measured by the ASTM standard B611-85 test. Int J Refract Metal Hard Mater 15 (1997) 73-79
15. Larsen-Basse J., and Koyanagi E.T. Abrasion of WC-Co alloys by quartz. Trans ASME 101 (1979) 208-211
16. Sinha S.K., Reddy S.U., and Gupta M. Scratch hardness and mechanical property correlation for Mg/SiC and Mg/SiC/Ti metal-matrix composites. Tribol Int 39 (2006) 184-189
17. ISO 14577 TR. Metallic materials - hardness test - universal test (1995), International Organization for Standardization, Geneva, Switzerland
18. ISO 14577-1. Metallic materials-instrumented indentation test for hardness and materials parameters. Part 1. Test method (2002), International Organization for Standardization, Geneva, Switzerland
19. Kato K., Hokkirigawa K., Kayaba T., and Endo Y. Three dimensional shape effect on abrasive wear. J Tribol - Trans ASME 108 (1986) 346-351
20. Xie Y., and Williams J.A. The prediction of friction and wear when a soft surface slides against a harder rough surface. Wear 196 (1996) 21-34
21. Xie Y., and Hawthorne H.M. On the possibility of evaluating the resistance of materials to wear by ploughing using a scratch method. Wear 240 (2000) 65-71
22. Lawn B.R. Indentation of ceramics with spheres: a century after Hertz. J Am Ceram Soc 81 8 (1998) 1977-1993
23. Fredrik W., and Per-Lennart L. Scratch testing of metals and polymers: experiments and numerics. Wear 266 (2009) 76-83
24. Godara A., Raabe D., and Green S. The influence of sterilization processes on the micromechanical properties of carbon fiber-reinforced PEEK composites for bone implant applications. Acta Biomater 3 (2007) 209-220
25. Hodzic A., Kim J.K., and Stachurski Z.H. Nano-indentation and nano-scratch of polymer/glass interfaces. II: Model of interphases in water aged composite materials. Polymer 42 (2001) 5701-5710
26. Hodzic A., Kalyanasundaram S., Kim J.K., Lowe A.E., and Stachurski Z.H. Application of nano-indentation, nano-scratch and single fibre tests in investigation of interphases in composite materials. Micron 32 (2001) 765-775
27. Bora MO, Çoban O, Si{dotless}nmazçelik T, Günay V. Effect of fiber orientation on scratch resistance in unidirectional carbon-fiber-reinforced polymer matrix composites. J Reinf Plast Comp. doi:10.1177/0731684408103953.
28. Jardret V., Zahouani H., Loubet J.L., and Mathia T.G. Understanding and quantification of elastic and plastic deformation during a scratch test. Wear 218 (1998) 8-14
29. Briscoe B.J., and Sinha S.K. Scratch resistance and localised damage characteristics of polymer surfaces - a review. Materialwiss Werkst 34 10/11 (2003) 989-1002 10.1002/mawe.20030068
30. Misra R.D.K., Nathani H., Dasari A., Wanjale S.D., and Jog J.P. The determining role of clay particles on mechanically induced surface damage and associated stress whitening in polybutene-clay nanocomposites. Mater Sci Eng A - Struct 386 (2004) 175-185
31. Moghbelli E., Browning R.L., Boo W.-J., Hahn S.F., Feick L.J.E., and Sue H.-J. Effects of molecular weight and thermal history on scratch behavior of polypropylene thin sheets. Tribol Int 41 (2008) 425-433