Failure criteria for FRP adhesive lap joints: A comparative analysis

Mechanics of Advanced Materials and Structures

Volumn 17, Issue 2, 2010, Pages 157-164

  Ascione, Francesco ^a   Mancusi, Geminiano ^b  

^a UNIVERSITY OF ROME TOR VERGATA   (Italy)

^b UNIVERSITY OF SALERNO   (Italy)

Author keywords

Adhesive lap joints; Debonding; FRP

Indexed keywords

COHESIVE INTERFACE; COMPARATIVE ANALYSIS; DEFORMABILITY; FAILURE CRITERIA; FINITE ELEMENT ANALYSIS; FRP; INTERFACE FAILURE; LAP JOINT; LINEAR ELASTIC; MATHEMATICAL FORMULATION; MECHANICAL PROBLEMS; NON-LINEAR; NUMERICAL RESULTS;

DEBONDING; FIBER REINFORCED PLASTICS; NUMERICAL ANALYSIS; REINFORCED PLASTICS;

QUALITY ASSURANCE;

EID: 77149143249     PISSN: 15376494     EISSN: 15376532     Source Type: Journal    
DOI: 10.1080/15376490903556659     Document Type: Article

References (20)

1. Z. Suo and J.W. Hutchinson, Interface Crack Between Two Elastic Layers, Int. J Fracture, vol. 43, pp. 1-18, 1990.
2. J.S. Wang and Z. Suo, Experimental Determination of Interfacial Toughness Using Brazil-Nut-Sandwich, Acta Metall Mater, vol. 38, pp. 1279-1290, 1990.
3. J.W. Hutchinson and Z. Suo, Mixed-mode Cracking in Layered Materials, Adv Appl Mech, vol. 29, pp. 63-191, 1992.
4. X.P. Xu and A. Needleman, Void Nucleation by Including Debonding in a Crystal Matrix, Modeling Simulation. Mater. Sci. Eng., vol. 1, pp. 111-132, 1993.
5. G. Fernlund, M. Papini, D. McCammond, and J.K. Spelt, Fracture Load Predictions for Adhesive Joints, Composite Science and Technology, vol. 51, pp. 587-600, 1994.
6. M. Papini, G, Fernlund, and J.K. Spelt, The Effects of Geometry on the Fracture of Adhesive Joints, Int J Adhes Adhes, vol. 14, pp. 5-13, 1994.
7. G.T. Camacho and M. Ortiz, Computational Modelling of Impact Damage in Brittle Materials, Int. J Solids Struct, vol.33, pp. 2899-2938, 1996.
8. T. Keller, and T. Vallée, Adhesively Bonded Lap Joints from Pultruded GFRP Profiles. Part I: Stress-strain Analysis and Failure Modes, Compos Part B-Eng, vol. 36, pp. 331-340, 2005.
9. T. Keller, and T. Vallée, Adhesively Bonded Lap Loints from Pultruded GFRP Profiles. Part II: Joint Strength Prediction, Compos Part B-Eng, vol. 36, pp. 311-350, 2005.
10. T. Keller, and T. Vallée, Adhesively Bonded Lap Joints from Pultruded GFRP Profiles. Part II: Effects of Chamfers, Compos Part B-Eng, vol. 37, pp. 328-336, 2005.
11. A. Corigliano, S. Mariani, and A. Pandolfi, Numerical Analysis of Rate-dependent Dynamic Composite Delamination, Composites Science and Technology, vol.66, pp. 766-775, 2006.
12. F. Ascione, Modellazione di Giunti di FRP, PhD thesis at University of Rome "Tor Vergata," 2007.
13. F. Ascione, Mechanical Behaviour of FRP Adhesive Joints: A Theoretical Model, Compos Part B-Eng, vol. 40, pp. 116-124, 2009.
14. F. Ascione, Ultimate Behaviour of Adhesively Bonded FRP Lap Joints, Compos Part B-Eng, vol. 40, pp. 107-115, 2009.
15. L.F.M. Da Silva, Special Topic Issue on Structural Adhesive Joints, Int J Adhes Adhes, vol. 28, pp. 391-392, 2008.
16. F. Ascione, and G. Mancusi, Axial/Bending Coupled Analysis for FRP Adhesive Lap Joints, Mech Adv Mater Struc, vol. 17, pp. 1-14, 2010.
17. M. Ortiz, and A. Pandolfi, Finite-deformation Irreversible Cohesive Elements for Three-dimensional Crack-propagation Analysis, Int. J. Numer. Meth. Engng., vol. 44, pp. 1267-1282, 1999.
18. J.N. Reddy, An Introduction to the Finite Element Method, 2nd Ed., New York, McGraw-Hill, 1992.
19. J.N. Reddy, Mechanics of Laminated Composite Plates-Theory and Analysis, CRC Press, 1997.
20. CNR DT 205/2007, Guide for the Design and Construction of Structures Made of FRP Pultruded Elements, Advisory Committee on Technical Recommendations for Constructions, Italian National Research Council.