Experimental and numerical investigation of trailing edge film cooling by circular coolant wall jets ejected from a slot with internal rib arrays

Journal of Turbomachinery

Volumn 126, Issue 2, 2004, Pages 229-236

  Martini, P ^a   Schulz, A ^a  

^a UNIVERSITY OF KARLSRUHE   (Germany)

Author keywords

[No Author keywords available]

Indexed keywords

ADIABATIC ENGINES; COOLANTS; JETS; PRESSURE MEASUREMENT; TURBOMACHINE BLADES;

NUMERICAL INVESTIGATION; SLOT WIDTH; TRAILING EDGE FILM; TURBINE BLADE;

TURBINES;

MATHEMATICAL ANALYSIS;

EID: 7644220314     PISSN: 0889504X     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1645531     Document Type: Article

References (19)

1. Seban, R. A., and Back, L. H., 1962, "Effectiveness and Heat Transfer for a Turbulent Boundary Layer with Tangential Injection and Variable Free-Stream Velocity," ASME J. Heat Transfer, 84, pp. 235-244.
2. Samuel, A. E., and Joubert, P. N., 1965, "Film Cooling of an Adiabatic Plate in Zero Pressure Gradient in the Presence of a Hot Mainstream and Cold Tangential Secondary Injection," ASME J. Heat Transfer, 87, pp. 409-417.
3. Kacker, S. C., and Whitelaw, J. H., 1968, "The Effect of Slot Height and Slot Turbulence Intensity on the Effectiveness on the Uniform Density, Two-Dimensional Wall Jet," ASME J. Heat Transfer, 90, pp. 469-475.
4. Sivasegaram, S., and Whitelaw, J. H., 1969, "Film Cooling Slots: The Importance of Lip Thickness and Injection Angle," J. Mech. Eng. Sci., 11(1), pp. 22-27.
5. Goldstein, R. J., 1971, "Film Cooling," Adv. Heat Transfer, 7, pp. 321-379.
6. Ballal, D. R., and Lefebvre, A. H., 1973, "Film-Cooling Effectiveness in the Near Slot Region," ASME J. Heat Transfer, 95, pp. 265-266.
7. Mukherjee, D. K., 1976, "Film Cooling With Injection Trough Slots," ASME J. Eng., 98, pp. 556-559.
8. Bittlinger, G., Schulz, A., and Wittig, S., 1994, "Film Cooling Effectiveness and Heat Transfer Coefficients for Slot Injection at High Blowing Ratios," ASME Paper 94-GT-182.
9. Taslim, M. E., Spring, S. D., and Mehlman, B. P., 1990, "An Experimental Investigation of Film Cooling Effectiveness for Slots of Various Exit Geometries," Paper No. AIAA-90-2266.
10. Holloway, D. S., Leylek, J. H., and Scott, F. A., 2002, "Pressure Side Bleed Film Cooling: Part 1-Steady Framework for Experimental and Computational Results," ASME Paper GT-2002-30471.
11. Holloway, D. S., Leylek, J. H., and Scott, F. A., 2002, "Pressure Side Bleed Film Cooling: Part 2-Unsteady Framework for Experimental and Computational Results," ASME Paper GT-2002-30472.
12. Sturgess, G. J., 1985, "Design of Combustor Cooling Slots for High Film Effectiveness: Part 1-Film General Development," ASME Paper 85-GT-35.
13. Sturgess, G. J., and Pfeiffer, G. D., 1985, "Design of Combustor Cooling Slots for High Film Effectiveness: Part 2-Film Initial Development," ASME Paper 85-GT-36.
14. Rastogi, A. K., and Whitelaw, J. H., 1973, "The Effectiveness of Three Dimensional Film-Cooling Slots-1. Measurements," Int. J. Heat Mass Transfer, 16, pp. 1665-1681.
15. Nina, M. N. R., and Whitelaw, J. H., 1971, "The Effectiveness of Film Cooling With Three Dimensional Slot Geometries," ASME Paper 71-GT-11.
16. Martini, P., Schulz, A., Whitney, C. F., and Lutum, E., 2003, "Experimental and Numerical Investigation of Trailing Edge Film Cooling Downstream of a Slot with Internal Rib Arrays," 5th European Conference on Gas Turbines, to be published.
17. Roach, P. E., 1987, "The Generation of Nearly Isotropic Turbulence by Means of Grids," Heat and Fluid Flow, 8(2), pp. 83-92.
18. Gritsch, M., Baldauf, S., Martiny, M., Schulz, A., and Wittig, S., 1999, "The Superposition Approach to Local Heat Transfer Coefficients in High Density Ratio Film Cooling Flows," ASME Paper 99-GT-168.
19. Bittlinger, G., 1995, "Filmkühlung mit tangentialer Spaltausblasung: Experimentelle und numerische Ansätze zur Optimierung des Brennkammer-Kühlluftbedarfes," Ph.D. thesis, Institut für Thermische Strömungsmaschinen (ITS),