Microstructures of hot-rolled high-strength steels with significant differences in edge formability

Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science

Volumn 32, Issue 13, 2001, Pages 745-760

  Misra, R D K ^a   Thompson, S W ^b   Hylton, T A ^c   Boucek, A J ^d  

^a University of Louisiana at Lafayette   (United States)

^b Department of Geology and Geological Engineering   (United States)

^c LTV Copperweld Tubular Products Company   (United States)

^d Technology Center   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

A-CARBON; DISLOCATION SUBSTRUCTURES; EXPANSION VALUE; FINE STRUCTURES; FRACTURE SURFACES; GRAIN-SIZE DISTRIBUTION; HARDNESS RATIO; HIGH HARDNESS; HIGH-STRENGTH STEELS; HOT-ROLLED; LOW HARDNESS; LOW TEMPERATURES; MICRO-STRUCTURAL CHARACTERIZATION; MICROPLASTICITY; MICROSTRUCTURAL BANDING; PROEUTECTOID FERRITE; STEEL COMPOSITIONS; TOTAL ELONGATIONS; TRANSFORMATION PRODUCTS; YIELD STRENGTH;

FERRITE; HARDNESS; MANGANESE; MANGANESE COMPOUNDS; MARTENSITIC STAINLESS STEEL; MICROSTRUCTURE; TENSILE STRENGTH;

HIGH STRENGTH STEEL;

EID: 73349143622     PISSN: 10735623     EISSN: None     Source Type: Journal    
DOI: 10.1007/s11661-001-1009-6     Document Type: Article

References (51)

1. R.R. Hilson, T.E. Fine, and G.J. Hansen: Microalloying '75, Union Carbide, New York, NY, 1977, pp. 654-64.
2. H. Takechi: in Hot- & Cold-Rolled Sheet Steels, R. Pradhan and G. Ludkovsky, eds., TMS-AIME, Warrendale, PA, 1988, pp. 117-38.
3. T. Maksuoka, T. Kawai, Y. Hobo, and S. Ueda: Trans. Iron Steel Inst. Jpn., 1975, vol. 15, pp. 137-44.
4. Y.J. Park, A.P. Coldren, and J.W. Morrow: in Fundamentals of Dual-Phase Steels, R.A. Kot and B.L. Bramfitt, eds., TMS-AIME, Warrendale, PA, 1981, pp. 485-97.
5. M. Sudo, S. Hashimoto, and S. Kambe: Trans. Iron Steel Inst. Jpn., 1983, vol. 23, p. 303.
6. N. Nagao, K. Kunishigie, S. Hamamatsu, and T. Nunokawa: in Accelerated Cooling of Steel, P. Southwick, ed., TMS-AIME, Warrendale, PA, 1985, p. 463.
7. S. Hashimoto, M. Sudo, K. Mimura, and T. Hosada: Trans. Iron Steel Inst. Jpn., 1986, vol. 26, p. 985.
8. M. Mizui and M. Takahashi: Iron Steelmaker, 1992, vol. 19(9), pp. 31-38.
9. H. Kimura, T. Ogura, M. Kinoshita, T. Okita, and K. Osawa: SAE Technical Paper No. 930283, SAE, Warrendale, PA, 1993.
10. I. Machida, M. Narita, R. Kurera, N. Aoyagi, and M. Sano: SAE Technical Paper No. 940536, SAE, Warrendale, PA, 1994.
11. S. Toyoda, T. Urabe, K. Osawa, and M. Ohmura: Technical Report No. 58, NKK Corporation, 1997.
12. A. Schmitz, J. Neutjens, J.C. Herman, and V. Leroy: 40th MWSP Conf Proc., ISS, Warrendale, PA, 1998, vol. XXXVI, pp. 295-309.
13. J. Neutjens, P. Harlet, T. Bakolas, and P. Cantinieaux: 40th MWSP Conf Proc., ISS, Warrendale, PA, 1998, vol. XXXVI, pp. 311-21.
14. Metals Handbook, 10th ed., ASM, Materials Park, OH, 1990, vol. 1, pp. 573-90.
15. A. Nishimoto, Y. Hosoya, and K. Nakaoka: in Fundamentals of Dual- Phase Steels, R.A. Kot and B.L. Bramfitt, eds., TMS-AIME, Warrendale, PA, 1981, pp. 447-63.
16. R.D. Adamczyk, D.W. Dickson, and R.P. Krupitzer: SAE Technical Paper No. 830237, SAE, Warrendale, PA, 1983.
17. R.D. Adamczyk and D.W. Dickson: J. Appl. Metalworking, 1986, vol. 4, p. 157.
18. H. Asano, N. Matsuzu, A. Itami, and K. Koyama: SAE Technical Paper No. 940943, SAE, Warrendale, PA, 1994.
19. M. Sudo and I. Koubo: Scand. J. Metall., 1984, vol. 13, p. 329.
20. Y. Ito, K. Hashigichi, and N. Ohashi: Proc. ICSTIS, 1971, Sect. 5, p. 958.
21. A.J. Klein and E.W. Hitchler: Met. Eng. Q., 1973, Aug., p. 157.
22. M. Sudo and T. Iwai: Trans. Iron Steel Inst. Jpn. 1983, vol. 23, pp. 294-302.
23. 1989 Annual Book of ASTM Standards, ASTM Designation E 8, ASTM, Philadelphia, PA, 1989, vol. 03.01, pp. 131-46.
24. 1989 Annual Book of ASTM Standards, ASTM Designations E 112 and E 562, ASTM, Philadelphia, PA, 1989, vol. 03.01, pp. 284-309 and pp. 582-86, respectively.
25. 1989 Annual Book of ASTM Standards, ASTM Designation E 112, ASTM, Philadelphia, PA, 1989, vol. 03.01, pp. 284-309.
26. B.D. Cullity: Elements of X-ray Diffraction, 2nd ed., Addison-Wesley, Reading, MA, 1978, p. 412.
27. 1989 Annual Book of ASTM Standards, ASTM Designations A 370, ASTM, Philadelphia, PA, 1989, vol. 03.01, pp. 3-48.
28. T. Parayil and G. Ludkovsky: Proc. Int. Symp. on Accelerated Cooling of Rolled Steels, G.E. Ruddle and A.F. Crawley, ed., Pergamon Press, New York, NY, 1988, pp. 131-44.
29. P. Messien, J.-C. Herman, and T. Gréday: in Fundamentals of Dual- Phase Steels, R.A. Kot and B.L. Bramfitt, eds., TMS-AIME, Warrendale, PA, 1981, pp. 161-80.
30. G.R. Speich and R.L. Miller: Proc. Int. Conf. Solid → Solid Phase Transformations, H.I. Aaronson, D.E. Laughlin, R.F. Sekerka, and C.M. Wayman, eds., TMS-AIME, Warrendale, PA, 1982, pp. 843-48.
31. J.S. Kirkaldy, J. von Destinon-Forstmann, and R.J. Brigham: Can. Metall. Q., 1962, vol. 1, pp. 59-81.
32. L.J. Habraken and M. Economopoulos: Transformation and Harden- ability in Steels, Climax Molybdenum Co., Ann Arbor, MI, 1967, pp. 69-107.
33. A.R. Marder and G. Krauss: Trans. ASM, 1967, vol. 60, pp. 651-60.
34. E. Scheil: Z. Metallkd., 1942, vol. 34, p. 70.
35. R.M. Fisher, G.R. Speich, L.J. Cuddy, and Hsun Hu: in Physical Chemistry in Metallurgy, R.M. Fisher, R.A. Oriani, and E.T. Turkdo- gan, eds., U.S. Steel, Monroeville, PA, 1976, pp. 463-88.
36. S.W. Thompson and P.R. Howell: Mater. Sci. Technol., 1992, vol. 8, pp. 777-84.
37. K.W. Andrews: J. Iron Steel Inst., 1965, vol. 203, pp. 721-27.
38. C. Wells and R.F. Mehl: Trans. AIME, 1940, vol. 140, pp. 279-306.
39. C.A. Muojekwu, D.Q. Jin, V.H. Hernandez, I.V. Samarasekera, and J.K. Brimacombe: 38th MWSP Conf Proc., ISS, Warrendale, PA, 1997, vol. XXXIV, pp. 351-66.
40. C.A. Muojekwu, D.Q. Jin, V.H. Hernandez, I.V. Samarasekera, and J.K. Brimacombe: 39th MWSP Conf Proc., ISS, Warrendale, PA, 1998, vol. XXXV, p. 219.
41. L. Brewer, J. Chipman, and S.-G. Chang: Metals Handbook, 8th ed. ASM, Metals Park, OH, 1973, vol. 8, pp. 407-08.
42. J.M. Moyer and G.S. Ansell: Metall. Trans. A, 1975, vol. 6A, pp. 175-91.
43. G.R. Speich: in Fundamentals of Dual-Phase Steels, R.A. Kot and B.L. Bramfitt, eds., TMS-AIME, Warrendale, PA, 1981, pp. 3-45.
44. I. Tamura, C. Ouchi, T. Tanaka, and H. Sekine: Thermomechanical Processing of High Strength Low Alloy Steels, Butterworth & Co. (Publishers) Ltd., Boston, MA, 1988, p. 142.
45. C. Ouchi, T. Sampei, and I. Kozasu: Trans. Iron Steel Inst. Jpn., 1982, vol. 22, p. 214.
46. S. Modin: Jernkont. Ann., 1958, vol. 142, pp. 37-80.
47. D. Cheetham and N. Ridley: Met. Sci., 1975, vol. 9, pp. 411-14.
48. M.S. Rashid: in Formable HSLA and Dual-Phase Steels, A.T. Davenport, ed., TMS-AIME, Warrendale, PA, 1979, pp. 3-24.
49. J.M. Rigsbee, J.K. Abraham, A.T. Davenport, J.E. Franklin, and J.W. Pickens: in Structure and Properties of Dual-Phase Steels, R.A. Kot and J.W. Morris, eds., TMS-AIME, Warrendale, PA, 1979, pp. 304-29.
50. G. Krauss: in Hardenability Concepts with Applications to Steel, D.V. Doane and J.S. Kirkaldy, eds., TMS-AIME, Warrendale, PA, 1978, pp. 229-45.
51. R. Stevenson: in Formable HSLA and Dual-Phase Steels, A.T. Davenport, ed., TMS-AIME, Warrendale, PA, 1979, pp. 99-108.