Debonding initiation in a NiTi shape memory wire-epoxy matrix composite. Influence of martensitic transformation

Materials and Design

Volumn 31, Issue 3, 2010, Pages 1077-1084

  Payandeh, Yousef ^a   Meraghni, Fodil ^a   Patoor, Etienne ^a   Eberhardt, André ^a  

^a UNIVERSITÉ PAUL VERLAINE METZ   (France)

Author keywords

A. NiTi wire composite; E. Martensitic transformation; I. Debonding initiation

Indexed keywords

A. NITI WIRE COMPOSITE; ANALYTICAL MODEL; COMPOSITE SAMPLES; E. MARTENSITIC TRANSFORMATION; EMBEDDED WIRES; EPOXY-MATRIX COMPOSITE; HEAT TREATMENT CYCLE; IN-SITU OBSERVATIONS; INTERFACIAL DEBONDING; INTERFACIAL SHEAR STRENGTH; LATERAL SURFACE; NI-TI WIRE; NO PHASE; PHASE TRANSFORMATION; PULL-OUT TEST; SHAPE MEMORY; SHAPE MEMORY WIRES; STEEL WIRE;

DEBONDING; MARTENSITE; SHEAR STRENGTH; WIRE;

MARTENSITIC TRANSFORMATIONS;

EID: 72149122903     PISSN: 02641275     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.matdes.2009.09.048     Document Type: Article

References (39)

1. Shimamoto A., Ohkawara H., and Nogata F. Enhancement of mechanical strength by shape memory effect in TiNi fiber-reinforced composites. Eng Fract Mech 71 (2004) 737-746
2. Jonnalagadda K., Kline G.E., and Sottos N.R. Local displacements and load transfer in shape memory alloy composites. Exp Mech 37 1 (1997) 78-85
3. Lau K., Chan A.W., Shi S., and Zhou L. Debond induced by strain recovery of an embedded NiTi wire at a NiTi-epoxy interface: micro-scale observation. Mater Des 23 (2002) 265-270
4. Poon C., Lau K., and Zhou L. Design of pull-out stresses for prestrained SMA wire/polymer hybrid composites. Compos Part B: Eng 36 1 (2005) 25-31
5. Marfia S. Micro-macro analysis of shape memory alloy composites. Int J Solids Struct 42 (2005) 3677-3699
6. Neuking K., Abu-Zarifa A., Youcheu-Kemtchou S., and Eggeler G. Polymer/NiTi-composites: fundamental aspects, processing and properties. Adv Eng Mater 7 (2005) 1014-1023
7. Kim C. A smart polymer composite actuator with thin SMA strips. Int J Mod Phys B 20 (2006) 3733-3738
8. Tahiri V.L., Patoor E., and Eberhardt A. An analysis of the thermomechanical behaviour of a shape memory alloy/elastomer composite. J Phys IV 115 (2004) 195-203
9. Winzek B., Sterzl T., Rumpf H., and Quandt E. Composites of different shape memory alloys and polymers for complex actuator motions. J Phys IV 112 (2003) 1163-1168
10. Murasawa G., Tohgo K., and Ishii H. Deformation behavior of NiTi/polymer shape memory alloy composites - experimental verifications. J Compos Mater 38 (2004) 399-416
11. Smith N.A., Antoun G.G., Ellis A.B., and Crone W.C. Improved adhesion between nickel-titanium shape memory alloy and a polymer matrix via silane coupling agents. Compos Part A: Appl S 35 (2004) 1307-1312
12. Jang B.K., and Kishi T. Adhesive strength between TiNi fibers embedded in CFRP composites. Mater Lett 59 11 (2005) 1338-1341
13. Neuking K., Abu-Zarifa A., and Eggeler G. Surface engineering of shape memory alloy/polymer-composites: improvement of the adhesion between polymers and pseudoelastic shape memory alloys. Mater Sci Eng A 481-482 (2008) 606-611
14. Rossi S., Deflorian F., Pegoretti A., D'Orazio D., and Gialanella S. Chemical and mechanical treatments to improve the surface properties of shape memory NiTi wires. Surf Coat Technol 202 (2008) 2214-2222
15. Fu S.Y., Yue C.Y., Hu X., and Mai Y.W. Analyses of the micromechanics of stress transfer in single-and multi-fibre pull-out tests. Compos Sci Technol 60 (2000) 569-579
16. Gao Y.C., and Zhou L.M. Energy release rate for interface debonding with prestress and friction. Theor Appl Fract Mech 32 (1999) 203-207
17. Yue C.Y., Looi H.C., and Quek M.Y. Assessment of wire-matrix adhesion and interfacial properties using the pull-out test. Int J Adhes Adhesiv 15 (1995) 73-80
18. Yallee R.B., and Young R.J. Evaluation of interface fracture energy for single-wire composites. Compos Sci Technol 58 (1998) 1907-1916
19. Guo S., Honda K., and Kagawa Y. Interface debonding from bottom face and frictional transition during push-out testing of a tungsten fibre-epoxy matrix composite. Compos Sci Technol 65 (2005) 1808-1814
20. Quek M.Y. Stress transfer at a partially bonded fibre/matrix interface. Int J Adhes Adhesiv 22 (2002) 303-310
21. Bannister D.J., Andrews M.C., Cervenka A.J., and Young R.J. Analysis of the single-fibre pull-out test by means of Raman spectroscopy. Part II: micromechanics of deformation for an aramid-epoxy system. Composites science and technology 53 (1995) 41l-421
22. Pisanova E., Zhandarov S., Mäder E., Ahmad I., and Young R.J. Three techniques of interfacial bond strength estimation from direct observation of crack initiation and propagation in polymer-fibre systems. Composites Part A 32 (2001) 435-443
23. Bennett J.A., and Young R.J. The effect of fibre-matrix adhesion upon crack bridging in fibre reinforced composites. Composites Part A 29 (1998) 1071-1081
24. Huang Y., and Young R.J. Interfacial behaviour in high temperature cured carbon fibre/epoxy resin model composite. Composites 26 (1995) 541-550
25. El-Tayeb N.S.M. Development and characterisation of low-cost polymeric composite materials. Mater Des 30 (2009) 1151-1160
26. Wang X., and Hu G. Stress transfer for a SMA fibre pulled out from an elastic matrix and related bridging effect. Composites Part A 36 (2005) 1142-1151
27. Paine J.S.N., and Rogers C.A. Characterization of interfacial shear strength between SMA actuators and host composite material in adaptive composite material systems. In: Carman G.P., and Garcia E. (Eds). Adaptive structures and material systems AD-35 (1993), ASME, New York 63-70
28. Poon C.K., Zhou L.M., and Yam L.H. Size effect on the optimum actuation condition for SMA-composites. Compos Struct 66 1-4 (2004) 503-511
29. Sadrnezhaad S.K., Hassanzadeh Nemati N., and Bagheri R. Improved adhesion of NiTi wire to silicone matrix for smart composite medical applications. Mater Des 30 9 (2009) 3667-3672
30. Zhou L.M., Kim J.K., and Mai Y.W. On the single fibre pull-out problem: effect of loading method. Compos Sci Technol 45 2 (1992) 153-160
31. Payandeh Y., Meraghni F., Patoor E., and Eberhardt A. Effect of martensitic transformation on the debonding propagation in NiTi shape memory wire composite. Mater Sci Eng A (2009) 10.1016/j.msea.2009.04.01
32. Vazquez-Rodriguez J.M., Herrera-Franco P.J., and González-Chi P.I. Analysis of the interface between a thermoplastic wire and a thermosetting matrix using photoelasticity. Composites Part A 38 (2007) 819-827
33. Ostachowicz W., Krawczuk M., and Zak A. Dynamics and buckling of a multilayer composite plate with embedded SMA wires. Compos Struct 48 (2000) 163-167
34. Hamada K., Lee J.H., Mizuuchi K., Taya M., and Inoue K. Thermomechanical behaviour of TiNi shape memory wire reinforced 6061 aluminium matrix composite. Metall Mater Trans A 29A (1998) 1127-1135
35. Sittner P., Landa M., Lukás P., and Novák V. R-phase transformation phenomena in thermomechanically loaded NiTi polycrystals. Mech Mater 38 (2006) 475-492
36. Liu Y., and Xiang H. Apparent modulus of elasticity of near-equiatomic NiTi. J Alloys Compd 270 (1998) 154-159
37. Niemczura J., and Ravi-Chandar K. Dynamics of propagating phase boundaries in NiTi. J Mech Phys Solids 54 (2006) 2136-2161
38. Sadrnezhaad S.K., and Hosseini S.A. Fabrication of porous NiTi-shape memory alloy objects by partially hydrided titanium powder for biomedical applications. Mater Des 30 10 (2009) 4483-4487
39. Piggott M.R. Load bearing fibre composites (1980), Pergamon, Canada