Staudinger's poly(cyclopentadiene): Sintering processing of poly(Diels-Alder cyclopentadiene)

Macromolecules

Volumn 42, Issue 18, 2009, Pages 6848-6850

  Veldman, Brittnee ^a,b   Kaully, Tamar ^a,b   Feller, Russell K ^b   Falcao, Eduardo ^b   Wudl, Fred ^a,b  

^a Department of Chemistry and Biochemistry ^*  (United States)

^b UNIVERSITY OF CALIFORNIA   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

AMORPHOUS POLYMERS; CYCLOPENTADIENES; DIELS-ALDER; FRACTURE SURFACES; GLASS TRANSITION TEMPERATURE; H NMR SPECTRA; HARDNESS MEASUREMENT; MELTING TEMPERATURES; O-DICHLOROBENZENE; PENTAMERS; PROCESSABLE; SEMICRYSTALLINES; SOLUBLE FRACTION; SURFACE HARDNESS;

FRACTURE; GLASS TRANSITION; HARDNESS; MECHANICAL PROPERTIES; MELTING POINT; NUCLEAR MAGNETIC RESONANCE SPECTROSCOPY; OLEFINS; PELLETIZING; POLYMER MELTS; SCANNING ELECTRON MICROSCOPY;

SINTERING;

EID: 70349900891     PISSN: 00249297     EISSN: None     Source Type: Journal    
DOI: 10.1021/ma901123p     Document Type: Article

References (16)

1. Woodson, C. S.; Grubbs, R. H. Cont.-in-part of U.S. 5,939,504, 2000; 12 pp.
2. Grubbs, R. H.; Hillmyer, M.; Benedicto, A.; Wu, Z. Polym. Prepr. (Am. Chem. Soc., Div. Polym. Chem.) 1994, 35, 688.
3. Staudinger, H.; Bruson, H. A. Justus Liebigs Ann. Chem. 1926, 446, 97-110.
4. Alder, K.; Stein, G. Justus Liebigs Ann. Chem. 1931, 485, 223-246.
5. Ann. Chem. 1932, 496, 204-251.
6. Chem. Ber. 1934, 67, 613-627.
7. Wilson, P. J.; Wells, J. H. Chem. Rev. 1944, 34,1-50.
8. Vick, L. W.; Kander, R. G. Polym. Eng. Sci. 1998, 38 (11), 1824-1996.
9. Bigg, D. M., Epstein, M. M., Eds.; Suh, N. P.; Sung, N.-H. Sci. Technol. Polym. Process., Proc. Int. Conf, 1979, 897-919.
10. Lao, L. Master of Science Thesis, UCLA, 2001.
11. We thank our former colleague Prof. Y. Rubin for the results of MM calculations at the MM3 level.
12. Note: the DuPont PTFE 7C, in ref 9, which was found to be 76% crystalline, had a fwhm of 0.5. Though the full width at half- maximum is a measure of correlation length, it can be used as an approximation for crystalline domain size.
13. Rae, P. J.; Dattelbaum, D. M. Polymer 2004, 45, 7615-7625.
14. Murphy, E. B.; Bolanos, E.; Schaffner-Hamann, C.; Wudl, F.; Nutt, S. R.; Auad, M. L. Macromolecules 2008, 41, 5203-5209, and references therein.
15. ASTM C373-88(2006) Standard Test Method for Water Absorption, Bulk Density, Apparent Porosity, and Apparent Specific Gravity of Fired Whiteware Products.
16. Commercially available samples of PMMA and polycarbonate were indented under the same conditions as the pellets to yield hardness values of 157 and 243 MPa, respectively.