Tension buckling in multilayer elastomeric isolation bearings

Journal of Mechanics of Materials and Structures

Volumn 2, Issue 8, 2007, Pages 1591-1605

  Kelly, James M ^a   Takhirov, Shakhzod M ^a  

^a UNIVERSITY OF CALIFORNIA   (United States)

Author keywords

Linear theory; Nonlinear finite element analysis; Steel reinforced elastomeric seismic isolators; Tension and compression buckling

Indexed keywords

EID: 70349739025     PISSN: 15593959     EISSN: None     Source Type: Journal    
DOI: 10.2140/jomms.2007.2.1591     Document Type: Article

References (20)

1. ABAQUS 6.2 user manual, Version 6.2, Hibbitt Karlsson Sorensen Inc., Pawtucket, RI, 2001.
2. I. D. Aiken, J. M. Kelly, and F. F. Tajirian, "Mechanics of low shape factor elastomeric seismic isolation bearings", Technical report UCB/EERC-89/13, Earthquake Engineering Research Center, University of California, Berkeley, CA, 1989.
3. I. G. Buckle and J. M. Kelly, "Properties of slender elastomeric isolation bearings during shake table studies of a large-scale model bridge deck", pp. 247-269 in Joint sealing and bearing systems for concrete structures, vol. 1, American Concrete Institute, Detroit, MI, 1986.
4. I. G. Buckle and H. Liu, "Experimental determination of critical loads of elastomeric isolators at high shear strain", NCEER Bull. 8:3 (1994), 1-5.
5. I. Buckle, S. Nagarajaiah, and K. Ferrell, "Stability of elastomeric isolation bearings: experimental study", J. Struct. Eng. ASCE 128:1 (2002), 3-11.
6. C. J. Derham and A. G. Thomas, "The design of seismic isolation bearings", pp. 21-36 in Control of seismic response of piping systems and other structures by base isolation, Earthquake Engineering Research Center, University of California, Berkeley, CA, 1981.
7. A. N. Gent, "Elastic stability of rubber compression springs", J. Mech. Eng. Sci. 6:4 (1964), 318-326.
8. J. A. Haringx, "On highly compressible helical springs and rubber rods and their application for vibration-free mountings, I", Philips Res. Rep. 3 (1948), 401-449.
9. J. A. Haringx, "On highly compressible helical springs and rubber rods and their application for vibration-free mountings, II", Philips Res. Rep. 4 (1949), 49-80.
10. J. A. Haringx, "On highly compressible helical springs and rubber rods and their application for vibration-free mountings. III", Philips Res. Rep. 4 (1949), 206-220.
11. J. M. Kelly, Earthquake-resistant design with rubber, 2nd ed., Springer, London, 1997.
12. J. M. Kelly and S. M. Takhirov, "Analytical and numerical study on buckling of elastomeric bearings with various shape factors", Technical report UCB/EERC-2004/03, Earthquake Engineering Research Center, University of California, Berkeley, CA, 2004.
13. C. G. Koh and J. M. Kelly, "Effects of axial load on elastomeric bearings", Technical report UCB/EERC-86/12, Earthquake Engineering Research Center, University of California, Berkeley, CA, 1986.
14. C. G. Koh and J. M. Kelly, "A simple mechanical model for elastomeric bearings used in base isolation", Int. J. Mech. Sci. 30:12 (1988), 933-943.
15. C. G. Koh and J. M. Kelly, "Viscoelastic stability model for elastomeric isolation bearings", J. Struct. Eng. ASCE 115:2 (1989), 285-302.
16. S. Nagarajaiah and K. Ferrell, "Stability of elastomeric seismic isolation bearings", J. Struct. Eng. ASCE 125:9 (1999), 946-954.
17. C. W. Roeder, J. F. Stanton, and A. W. Taylor, "Performance of elastomeric bearings", NCHRP Rep. 298, Trans. Res. Board, National Research Council, Washington, D. C., 1987.
18. J. C. Simo and J. M. Kelly, "Finite element analysis of the stability of multilayer elastomeric bearings", Eng. Struct. 6:3 (1984), 162-174.
19. J. F. Stanton, G. Scroggins, A. W. Taylor, and C. W. Roeder, "Stability of laminated elastomeric bearings", J. Eng. Mech. ASCE 116:6 (1990), 1351-1371.
20. M. Takayama, H. Tada, and R. Tanaka, "Finite-element analysis of laminated rubber bearing used in base-isolation system", Rubber Chem. Technol. 65:1 (1992), 46-62. Rubber Division, ACS.