Predicting the cure of thermosetting polymers: The isoconversion map

Polymer Composites

Volumn 30, Issue 10, 2009, Pages 1450-1457

  Ruiz, Edu ^a,b   Billotte, C ^a  

^a DEPARTMENT OF CHEMICAL ENGINEERING   (Canada)

^b GENERAL MOTORS CORPORATION   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

CURE KINETICS; DYNAMIC DSC; ISOCONVERSION; MODEL FREE; RESIN CURE; TEMPERATURE PROFILES; THERMOSETTING POLYMERS; THERMOSETTING RESINS;

DIFFERENTIAL SCANNING CALORIMETRY; EPOXY RESINS; REACTION KINETICS; RESINS; TEMPERATURE CONTROL; THERMOSETS;

CURING;

EID: 70349559929     PISSN: 02728397     EISSN: 15480569     Source Type: Journal    
DOI: 10.1002/pc.20710     Document Type: Article

References (21)

1. Edu Ruiz and F. Trochu, Polym. Compos., 26(2), 209 (2005).
2. R.E. Cuthrel, J. Appl. Polym. Sci, 12(4), 955 (1968).
3. M. Gordon and I.D. McMillan, Die. Makromol. Chem, 23(1), 188 (1957)
4. C.D. Han and K.W. Lem, J. Appl. Polym. Sci, 29(5), 1879 (1984).
5. M.R. Kamal, Polym. Eng. Sci., 4(3), 239 (1974).
6. J.-L. Bailleul, V. Sobotka, D. Delaunay, and Y. Jarny, Compos. A, 34(8), 695 (2003).
7. Edu Ruiz and F. Trochu, J. Compos. Mater., 39(10), 881 (2005).
8. C.C. Riccardi, J. Dupuy, and R.J.J. Williams, J. Polym. Sci. Part B: Polym. Phys., 37, 2799 (1999).
9. Edu Ruiz, F. Waffo, J. Owens, C. Billotte, and F. Trochu, ''Modeling of Resin Cure Kinetics for Molding Cycle Optimization,'' Flow Processes in Composite Materials (FPCM- 8) Int. Conf, Ecole des Mines de Douai, France (2006)
10. D.O. Hummel and A. Solti, Atlas of Polymer and Plastics, Vol.1 and 2, VCH Publishers, New York (1988).
11. PolyKinetic software, Also available at http://cchp.meca. polymtl.ca (2006).
12. S. Han, W.G. Kim, H.G. Yoon, and T.J. Moon, J. Appl. Polym. Sci., 68, 1125 (1998).
13. C.-S. Chern and G.W. Poehlein, Polym. Eng. Sci., 27(11), 788 (1987).
14. J.M. Salla and X.A. Viermis, Polym. Eng. Sci., 36(6), 835 (1996).
15. C.R. Li and T.B. Tang, J. Mater. Sci., 34, 3467 (1999).
16. A. Atarsia and R. Boukhili, Polym. Eng. Sci., 40(3), 607 (2000).
17. M.J. Starink, Thermochim. Acta., 404, 163 (2003).
18. E.S. De Medeiros, J.A.M. Agnelli, K. Joseph, L.H. De Car-valho, and L.H.C. Mattoso, J. Appl. Polym. Sci., 90, 1678 (2003).
19. A.A. Varchenko and Y.A. Kraftmakher, Phys. Status. Sol-idi., 20(1), 387 (1973).
20. M.R. Kamal and S. Sourour, Polym. Eng. Sci., 13(1),59 (1973).
21. Edu Ruiz, De la caractéirisation des matéiriaux et simulation du procédé ǎ l'optimisation de la fabrication des composites par injection sur renfort, PhD Thesis, Ecole Polytechnique de Montreal, Department of Mechanical Engineering (2004).