Interleaving Delaunay refinement and optimization for practical isotropic tetrahedron mesh generation

ACM Transactions on Graphics

Volumn 28, Issue 3, 2009, Pages

  Tournois, Jane ^a   Wormser, Camille ^b   Alliez, Pierre ^a   Desbrun, Mathieu ^c  

^a INRIA   (France)

^b ETH ZURICH   (Switzerland)

^c CALIFORNIA INSTITUTE OF TECHNOLOGY   (United States)

Author keywords

Delaunay refinement; Graded meshing; Isotropic meshing; Mesh generation; Mesh optimization

Indexed keywords

DELAUNAY; DELAUNAY REFINEMENT; GRADED MESHING; ISOTROPIC MESHING; MESH OPTIMIZATION; PIECEWISE SMOOTH SURFACE; STEINER POINTS; TETRAHEDRAL MESHES; TETRAHEDRON MESH;

OPTIMIZATION;

MESH GENERATION;

EID: 70049105765     PISSN: 07300301     EISSN: 15577368     Source Type: Journal    
DOI: 10.1145/1531326.1531381     Document Type: Conference Paper

References (31)

1. ACAR, U., HUDSON, B., MILLER, G., AND PHILLIPS, T. 2007. SVR: Practical Engineering of a Fast 3D Meshing Algorithm. In Proc. of 16th Int. Meshing Roundtable, 45-62.
2. ALLIEZ, P., COHEN-STEINER, D., YVINEC, M., AND DESBRUN, M. 2005. Variational Tetrahedral Meshing. In Proc. of ACM SIGGRAPH 2005, vol.24(3), 617-625.
3. AMENTA, N., BERN, M., AND EPPSTEIN, D. 1999. Optimal Point Placement for Mesh Smoothing. J. of Algorithms 30, 2, 302-322.
4. ANTANI, L., DELAGE, C., AND ALLIEZ, P. 2007. Mesh Sizing with AdditivelyWeighted Voronoi Diagrams. In Proc. of the 16th Int. Meshing Roundtable, 335-346. Figure 11: Elephant. Top: mesh generated by Delaunay refinement with lmax = 0:1, emax = 0:001. Distribution of dihedral angles, and sliver tetrahedra with dihedral angles lower than 15 degrees are shown. Middle: output of Delaunay refinement (i.e., top row) optimized with our technique. Bottom: optimized mesh (middle row) after sliver perturbation.
5. BOISSONNAT, J.-D., WORMSER, C., AND YVINEC, M. 2007. Curved Voronoi diagrams. In Effective Comp. Geometry for Curves and Surfaces, Springer, Ed. 67-116.
6. BOIVIN, C., AND OLLIVIER-GOOCH, C. 2002. Guaranteed-quality Triangular Mesh Generation for Domains with Curved Boundaries. Int. J. Numer. Methods Eng. 55, 1185-1213.
7. CHEN, L., AND XU, J. 2004. Optimal Delaunay triangulations. J. of Comp. Mathematics 22, 2, 299-308.
8. CHEN, L. 2004. Mesh Smoothing Schemes based on Optimal Delaunay Triangulations. In Proc. of the 13th Int. Meshing Roundtable, 109-120.
9. CHENG, S., DEY, T., EDELSBRUNNER, H., FACELLO, M., AND TENG, S. 2000. Sliver Exudation. J. of the ACM 47, 5, 883-904.
10. CHENG, S., DEY, T., AND LEVINE, J. 2007. A Practical Delaunay Meshing Algorithm for a Large Class of Domains. In Proc. of the 16th Int. Meshing Roundtable, 477-494.
11. CHENG, S., DEY, T., AND RAMOS, E. 2007. Delaunay Refinement for Piecewise Smooth Complexes. In Proc. of the 18th Symp. on Discrete Algorithms, 1096-1105.
12. CHEW, L. 1989. Guaranteed-Quality Triangular Meshes. Tech. rep., Dept. of Computer Science, Cornell Univ.
13. CHEW, L. 1993. Guaranteed-quality Mesh Generation for Curved Surfaces. In Proc. of the 9th Symp. on Comp. Geometry, ACM NY, USA, 274-280.
14. DU, Q., FABER, V., AND GUNZBURGER, M. 1999. Centroidal Voronoi tesselations. SIAM Review 41, 4, 637-676.
15. FREITAG, L., AND OLLIVIER-GOOCH, C. 1997. Tetrahedral Mesh Improvement using Swapping and Smoothing. Int. J. for Num. Methods in Eng. 40, 21, 3979-4002.
16. GEORGE, P.-L. 2004. Tetmesh-GHS3D, Tetrahedral Mesh Generator. INRIA User's Manual, INRIA (Institut National de Recherche en Informatique et Automatique), France.
17. KLINGNER, B., AND SHEWCHUK, J. 2007. Aggressive Tetrahedral Mesh Improvement. In Proc. of the 16th Int. Meshing Roundtable, 3-23.
18. LABELLE, F., AND SHEWCHUK, J. 2007. Isosurface Stuffing: Fast Tetrahedral Meshes with Good Dihedral Angles. In ACM Transactions on Graphics, vol.26(3), No.57.
19. LI, X. 2000. Sliver-free 3-Dimensional Delaunay Mesh Generation. PhD thesis, University of Illinois at Urbana-Champaign.
20. NAVE, D., CHRISOCHOIDES, N., AND CHEW, L. 2002. Guaranteed Quality Parallel Delaunay Refinement for Restricted Polyhedral Domains. Proc. of the 18th Symp. on Comp. Geometry, 135-144.
21. OUDOT, S., RINEAU, L., AND YVINEC, M. 2005. Meshing Volumes Bounded by Smooth Surfaces. In Proc. of the 14th Int. Meshing Roundtable, 203-219.
22. PERSSON, P., AND STRANG, G. 2004. A Simple Mesh Generator in MATLAB. SIAM Review, 329-346.
23. RINEAU, L., AND YVINEC, M. 2007. Meshing 3D Domains Bounded by Piecewise Smooth Surfaces. In Proc. of the 16th Int. Meshing Roundtable, 443-460.
24. SHEWCHUK, J. 2002. Delaunay Refinement Algorithms for Triangular Mesh Generation. Comp. Geometry: Theory and Applications 22, 1-3, 21-74.
25. SHEWCHUK, J. 2002. What is a Good Linear Element? Interpolation, Conditioning, and Quality Measures. In Proc. of the 11th Int. Meshing Roundtable, 115-126.
26. SI, H., 2007. TETGEN, A Quality Tetrahedral Mesh Generator and 3-Dimensional Delaunay Triangulator. http://tetgen.berlios.de/.
27. TERDIMAN, P., 2005. OPCODE 3D Collision Detection library. http://www.codercorner.com/Opcode.htm.
28. TOURNOIS, J., ALLIEZ, P., AND DEVILLERS, O. 2007. Interleaving Delaunay Refinement and Optimization for 2D Triangle Mesh Generation. In Proc. of the 16th Int. Meshing Roundtable.
29. TOURNOIS, J. 2009. Mesh Optimization. PhD thesis, INRIA, Univ. de Nice Sophia Antipolis, France.
30. WENDT, J. D., BAXTER, W., OGUZ, I., AND LIN, M. C. 2007. Finite Volume Flow Simulations on Arbitrary Domains. Graphical Models 69, 1, 19-32.
31. WU, J., AND KOBBELT, L. 2002. Fast Mesh Decimation by Multiple-Choice Techniques. Vision, Modeling, and Visualization 2002, 241-249.