Mechanical properties of thermally cycled nylon bonded Nd-Fe-B permanent magnets

Journal of Materials Science

Volumn 39, Issue 21, 2004, Pages 6509-6522

  Hemrick, J ^a   Lara Curzio, E ^a   Liu, Ken ^a   Ma, Bao Min ^b  

^a OAK RIDGE NATIONAL LABORATORY   (United States)

^b Magnequench Technology Center   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

CHEMICAL BONDS; CROSSLINKING; INJECTION MOLDING; NYLON POLYMERS; STRAIN; STRESS ANALYSIS; THERMAL CYCLING; TOUGHNESS; VOLUME FRACTION;

MORPHOLOGY PARTICLES; OPERATION TEMPERATURE; POWDER MORPHOLOGY; SERVICE TEMPERATURE;

PERMANENT MAGNETS;

EID: 6944229992     PISSN: 00222461     EISSN: None     Source Type: Journal    
DOI: 10.1023/B:JMSC.0000044890.42857.7a     Document Type: Article

References (14)

1. J. A. HORTON, J. L. WRIGHT and J. W. HERCHENROEDER, IEEE Trans. Magn. 32(5) (1996) 4374.
2. J. JIANG, Z. ZEN G and M. J. TOKUNAGA, J. Magn. Magn. Mater. 214(1) (2000) 61.
3. Y. M. RABINOVICH, V. V. SERGEEV, A. D. MAYSTRENKO, V. KULAKOVSKY, S. SZYMURA and H. BALA, Intermetallics 4(8) (1996) 641.
4. S. SZYMURA, Y. M. RABINOVICH, H. BALA and A. D. MAYSTERENKO, J. of Phys.: Cond. Matt. 6(19) (1994) 3573.
5. M. G. GARRELL, A. J. SHIH, B. M. MA, E. LARA CURZIO and R. O. SCATTERGOOD, Magn. Magn. Mater. 257 (2003) 32.
6. M. G. GARRELL, B. M. MA, E. LARA-CURZIO, A. J. SHIH and R. O. SCATTERGOOD, J. Mater. Eng. A 359(1/2) (2003) 375.
7. J. R. BROCKENBROUGH and S. SURESH, Scripta Metallurgica et Materialia. 24 (1990) 325.
8. C. R. CHEN, S. Y. QIN, S. X. LI and J. L. WEN, Mater. Sci. Engng. A 278 (2000) 96.
9. C. J. YANG, S. D. CHOI and W. Y. LEE, Powder Techn. 77 (1993) 285.
10. M. TAYA and R. J. ARSENAULT, "Metal Matrix Composites: Thermomechanical Behavior" (Pergamon Press, Oxford, England, 1989) p. 41.
11. "Standard Test Method for Tensile Strength of Plastics," ASTM D638 (American Society for Testing and Materials, West Conshocken, PA, 2001).
12. "Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending," ASTM D6272 (American Society for Testing and Materials, West Conshocken, PA, 2000).
13. H. C. HUA, G. Y. WANG, Q. Z. XU, H. J. JIN and G. Q. XU, Physica Status Solidi (A) Applied Research 125(2) (1991) 615.
14. G. R. MOORE and D. E. KLINE, "Properties and Processing of Polymers for Engineers" (Prentice-Hall, Inc., Englewood Cliffs, USA, 1984).