Discharge coefficients for a diesel injector during cold starting conditions

Atomization and Sprays

Volumn 19, Issue 7, 2009, Pages 621-631

  Vergnes, Cèlia ^a   Foucher, Fabrice ^a   Mounaïm Rousselle, Christine ^a  

^a Institut PRISME   (France)

Author keywords

[No Author keywords available]

Indexed keywords

DIESEL ENGINES; DIESEL FUELS; FUELS; HEPTANE; SPRAY NOZZLES;

CAVITATION PHENOMENON; COLD STARTING CONDITIONS; COLD TEMPERATURES; DISCHARGE COEFFICIENTS; INITIAL PERTURBATION; INJECTION COMPRESSION IGNITION ENGINE; SPRAY DEVELOPMENT; TEMPERATURE CONDITIONS;

DIRECT INJECTION;

EID: 68549090825     PISSN: 10445110     EISSN: None     Source Type: Journal    
DOI: 10.1615/atomizspr.v19.i7.20     Document Type: Article

References (25)

1. P. Bielaczyc, J. Merkisz, and J. Pielecha, Investigation of Exhaust Emissions Form DI Diesel Engine during Cold Start and Warm Start, SAE Paper No, 2001-01-1260, 2001.
2. H. Peng, Y. Cui, L. Shi, and K. Deg, Effects of Exhaust Gas Recirculation (EGR) on Combustion and Emissions during Cold Start of Direct Injection (DI) Diesel Engine, Energy, vol. 33, pp.471-479, 2008.
3. P. Pacaud, H. Perrin, and O. Laget, Cold Start on Diesel Engine: In Low Compression Ratio Compatible with Cold Start Requirement, SAE Paper No. 2008-01-1310, 2008.
4. H. Liu, N. A. Henein, and W. Bryzik, Simulations of Diesel Engines Cold-Start, SAE Paper No. 2003-01-0080, 2003.
5. H. Chaves, M. Knapp, A. Kubitzek, F. Obermeier, and T. Schneider, Experimental Study of Cavitation in the Nozzle Hole of Diesel Injectors Using Transparent Nozzles, SAE Paper No.950290, 1995.
6. F. Payri, J. Arrègle, J. J. Lopez, and S. Hermens, Effect of Cavitation on the Nozzle Outlet Flow, Spray and Flame Formation in a Diesel Engine, SAE Paper No. 2006-01-1391, 2006.
7. F. Payri, R. Payri, and F. J. Salvador, The Influenceof Cavitation on the Internal Flow and the Spray Characteristics in Diesel Injection Nozzles, Fuel, vol. 83, pp. 419-431, 2004.
8. C. Soteriou, M. Smith, and R. Andrews, Direct Injection Diesel Sprays and the Effect of Cavitation and Hydraulic Flip on Atomization, SAE Paper No. 950080, 1995.
9. H. Suh and C. Lee, Effect of Cavitation in Nozzle Orifice on the Diesel Fuel Atomization Characteristics, Int. J. Heat Fluid Flow, vol. 29, pp.1001-1009, 2008.
10. H. Hiroyasu and M. Arai, Fuel Spray Penetration and Spray Angle in Diesel Engines, Trans JSAE, vol. 21, pp. 5-11, 1980.
11. A. H. Lefebvre, Atomization and Sprays, N. Chigier, Ed., Hemisphere, Washington, DC, 1989.
12. D. L. Siebers, Scaling Liquid-Phase Fuel Penetration in Diesel Sprays Based on Mixing-Limited Vaporation, SAE Paper No. 1999-01-0528, 1999.
13. W. H. Nurick, Orifice Cavitation and Its Effect on Spray Mixing, ASME J. Fluids Eng., pp. 681-687, 1976.
14. C. Soteriou, R. Andrews, and M. Smith, Further studies of cavitation and atomization in diesel injection. SAE Papert No. 1999-01-1486, 1999.
15. H. Chaves, M. Knapp, A. Kubitzek, F. Obermeier, and T. Schneider, Experimental Study of Cavitation in the Nozzle Hole of Diesel Injectors Using Transparent Nozzles, SAE Paper No. 950290, 1995.
16. M. Gavaises and A. Andriotis, Cavitation Inside Multi-Hole Injectors for Large Diesel and Its Effect on Near-Nozzle Spray Structure, SAE Paper No. 2006-01-1114, 2006
17. R. Payri, J. M. Garcia, F. J. Salvador, and J. Gimeno, Using Spray Momentum Flux Measurements to Understand the Influence of Diesel Nozzle Geometry on Spray Characteristics, Fuel, vol. 84, pp. 551-561, 2005.
18. R. Payri, F. J. Salvador, J. Gimeno, and L. D. Zapata, Diesel Nozzle Geometry Influence on Spray Liquid-Phase Fuel Penetration in Evaporative Conditions, Fuel, vol. 87, pp. 1165-1176, 2008.
19. C. Martinez-Martinez, F. A. Sanchez-Cruz, J. M. Riesco-Avila, A. Gallegos-Munoz, and S. M. Aceves, Liquid Penetration Length in Direct Diesel Fuel Injection, Appl. Thermal Eng.,vol. 28, pp. 1756-1762, 2008.
20. B. E. Poling, J. M. Prausnitz, and J. P. O'Connel, The Properties of Gases and Liquids, 5th ed., McGraw Hill, New York, 2000.
21. V. Macian, R. Payri, X. Margot, and J. Salvador, A CFD Analysis of the Influence of Diesel Nozzle Geometry on the Inception of Cavitation, Atomization and Sprays, vol. 13, pp. 579-604,2003.
22. F. Payri, J. M. Garcia, F. Salvador, and J. Gimeno, Influence of Nozzle Geometry on Spray Characteristics in Non-Evaporating and Evaporative Conditions, SAE Paper No. 2007-24-0023, 2007.
23. P. D. Schmidt and L. M. Corradini, Analytical Prediction of the Exit Flow of Cavitating Orifices, Atomization and Sprays, vol. 7, pp. 603-616, 1997.
24. J. M. Desantes, R. Payri, F. Salvador, and J. Gimeno, Measurements of Spray Momentum for the Study of Cavitation in Diesel Injection Nozzles, SAE Paper No. 2003-01-0703, 2003.
25. A. Lichtarowicz and I. D. Pearce, Cavitation and Aeration Effects in Long Orifices, Cavitation, Proc. of Fluid Machinery Group of Inst. of Mech. Engineers, Mech. Eng. Publ. Ltd., London, p.437, 1974.