Effect of residual stresses on fatigue strength of severely surface deformed steels by shot peening

Powder Diffraction

Volumn 24, Issue SUPPL. 1, 2009, Pages

  Akiniwa, Yoshiaki ^a   Kimura, Hidehiko ^a   Sasaki, Takeo ^a  

^a NAGOYA UNIVERSITY   (Japan)

Author keywords

Constant penetration depth method; Residual stress; Shot peening; Synchrotron

Indexed keywords

AFTER-HEAT TREATMENT; CONSTANT PENETRATION DEPTH METHOD; FOUR-POINT BENDING; HIGH ENERGY X RAY; MEDIUM-CARBON STEELS; MONOCHROMATIC X-RAYS; RESEARCH INSTITUTES; SYNCHROTRON RADIATION SOURCE;

CARBON STEEL; RESIDUAL STRESSES; STRESS CONCENTRATION; SURFACE ROUGHNESS; SURFACES; SYNCHROTRON RADIATION; SYNCHROTRONS; X RAYS;

SHOT PEENING;

EID: 68249092600     PISSN: 08857156     EISSN: 19457413     Source Type: Journal    
DOI: 10.1154/1.3133132     Document Type: Conference Paper

References (17)

1. Akiniwa, Y., and Kimura, H. (2008). " Determination of residual stress distribution in severe surface deformed steel by shot peening.," Mater. Sci. Forum 0255-5476 571-572, 15-20. 10.4028/www.scientific.net/MSF.571- 572.15
2. Akiniwa, Y., Tanaka, K., Suzuki, K., Yanase, K., Nishio, E., Kusumi, K., and Okado, Y. J. (2003). " Evaluation of residual stress distribution in shot-peened steel by synchrotron radiation.," J. Soc. Mater. Sci. Jpn. 0514-5163 52, 764-769.
3. Bonarski, J. T., Wcislak, L., and Bunge, H. J. (1994). " Investigation of inhomogeneous textures of coatings and near-surface layers.," Mater. Sci. Forum 0255-5476 157-162, 111-117. 10.4028/www.scientific.net/MSF.157-162.111
4. Kroener, E. (1958). " Berechnung der elastischen Konstanten des Vielkristalls aus den Konstanten des Einkristalls.," Z. Phys. A: Hadrons Nucl. 0939-7922 151, 504-518.
5. Kumar, A., Welzel, U., and Mittemeijer, E. J. (2006). " A method for the non-destructive analysis of gradients of mechanical stresses by X-ray diffraction measurements at fixed penetration/information depths.," J. Appl. Crystallogr. 0021-8898 39, 633-646. 10.1107/S0021889806023417
6. Liu, Z. G., Fecht, H. J., and Umemoto, M. (2004). " Microstructural evolution and nanocrystal formation during deformation of Fe-C alloys.," Mater. Sci. Eng., A 0921-5093 375-377, 839-843. 10.1016/j.msea.2003.10.136
7. Roland, T., Retraint, D., Lu, K., and Lu, J. (2006). " Fatigue life improvement through surface nanostructuring of stainless steel by means of surface mechanical attrition treatment.," Scr. Mater. 1359-6462 54, 1949-1954. 10.1016/j.scriptamat.2006.01.049
8. SAE J784a (1971). " Residual stress measurement by X-ray diffraction.," SAE 2nd edition 0148-7191, 62-65.
9. Saito, Y., Tsuji, N., Utsunomiya, H., Sakai, T., and Hong, R. G. (1998). " Ultra-fine grained bulk aluminum produced by accumulative roll-bonding (ARB) process.," Scr. Mater. 1359-6462 39, 1221-1227. 10.1016/S1359- 6462(98)00302-9 (Pubitemid 128426428)
10. Tao, N. R., Sui, M. L., Lu, J., and Lu, K. (1999). " Surface nanocrystallization of iron induced by ultrasonic shot peening.," NanoStruct. Mater. 11, 433-440. 10.1016/S0965-9773(99)00324-4
11. Todaka, Y., Umemoto, M., Li, J., and Tsuchiya, K. J. (2005). " Nanocrystallization of drill hole surface by high speed drilling.," J. Metastable Nanocryst. Mater. 1422-6375 24-25, 601-604. 10.4028/www.scientific. net/JMNM.24-25.601
12. Valiev, R. Z., Krasilnikov, N. A., and Tsenev, N. K. (1991). " Plastic deformation of alloys with submicrograined structure.," Mater. Sci. Eng., A 0921-5093 137, 35-40. 10.1016/0921-5093(91)90316-F (Pubitemid 21648747)
13. Valiev, R. Z., Islamgaliev, R. K., and Alexandrov, I. V. (2000). " Bulk nanostructured materials from severe plastic deformation.," Prog. Mater. Sci. 0079-6425 45, 103-189. 10.1016/S0079-6425(99)00007-9
14. Wang, T., Yu, J., and Dong, B. (2006). " Surface nanocrystallization induced by shot peening and its effect on corrosion resistance of 1Cr18Ni9Ti stainless steel.," Surf. Coat. Technol. 0257-8972 200, 4777-4781. 10.1016/j.surfcoat.2005.04.046
15. Wang, T. S., Lu, B., Zhang, M., Hou, R. J., and Zhang, F. C. (2007). " Nanocrystallization and α martensite formation in the surface layer of medium-manganese austenitic wear-resistant steel caused by shot peening.," Mater. Sci. Eng., A 0921-5093 458, 249-252. 10.1016/j.msea.2006. 12.066
16. Warren, B. E. and Averbach, B. L. (1950). " The effect of cold-work distortion on X-ray patterns.," J. Appl. Phys. 0021-8979 21, 595-595. 10.1063/1.1699713
17. Wu, X., Tao, N., Hong, Y., Xu, B., Lu, J., and Lu, K. (2002). " Microstructure and evolution of mechanically-induced ultrafine grain in surface layer of AL-alloy subjected to USSP.," Acta Mater. 1359-6454 50, 2075-2084. 10.1016/S1359-6454(02)00051-4