Anomalies, influencing factors, and guidelines for DMA testing of fiber reinforced composites

Polymer Composites

Volumn 30, Issue 7, 2009, Pages 962-969

  Swaminathan, Gowthaman ^a   Shivakumar, Kunigal N ^a   Russell Jr , Larry C ^b  

^a NORTH CAROLINA A AND T STATE UNIVERSITY   (United States)

^b U S ARMY RESEARCH OFFICE   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

BASE MATRIX; DESIGN CHARTS; DYNAMIC PROPERTY; FIBER REINFORCED COMPOSITES; FIBER-REINFORCED COMPOSITE MATERIAL; GLASS TRANSITION TEMPERATURE; HIGH MODULUS CARBON FIBER; INFLUENCING FACTOR; MULTI-DIRECTIONAL; SPAN-TO-THICKNESS RATIO; TRANSVERSE SHEAR DEFORMATION; TWO GLASS TRANSITION; UNIDIRECTIONAL COMPOSITES;

CARBON FIBERS; COMPOSITE MICROMECHANICS; DYNAMIC ANALYSIS; DYNAMIC MECHANICAL ANALYSIS; FIBER REINFORCED PLASTICS; GLASS; GLASS TRANSITION; MECHANICAL PROPERTIES; PRESSURE DROP; SPECIMEN PREPARATION; SUPERCONDUCTING TRANSITION TEMPERATURE;

ASPECT RATIO;

EID: 67650786319     PISSN: 02728397     EISSN: 15480569     Source Type: Journal    
DOI: 10.1002/pc.20641     Document Type: Article

References (19)

1. K.P. Menard, Dynamic Mechanical Analysis - A Practical Introduction, 1st ed., CRC Press, Boca Raton (1999).
2. Annual Book of ASTM Standards, ASTM International, West Conshohocken, PA, 8.03 (1995).
3. M.V. Hosur, F.H. Chowdhury, and S. Jeelani, " Enhancement of Thermal and Mechanical Properties of Woven Carbon/ Epoxy Composites Through Nanoclay", ICCES-2005, December 1-6, India (2005).
4. F.H. Chowdhury, M.V. Hosur, and S. Jeelani, J. Mater. Sci., 42, 2690 (2005).
5. J.L. Abot, A. Yasmin, and I.M Daniel, J Reinforced Plast. Compos., 25, 195 (2005).
6. J.L. Abot, A. Yasmin, A. Jacobsen, and I.M Daniel, Compos. Sci. Technol., 64, 263 (2004).
7. A. Pirvu, D.J. Gardner, and R. Lopez-Anido, Compos. A, 35, 1257 (2004).
8. M.L. Costa, E.C. Botelho, J.M.F. Paiva, and M.C. Rezende, Mater. Res., 8, 317 (2005).
9. Annual Book of ASTM Standards, ASTM International, West Conshohocken, PA, 15.03 (2002).
10. E.P. Popov, Mechanics of Materials, 2nd ed., Prentice Hall, New Jersey (1976).
11. G. Swaminathan and K. Shivakumar, "A Re-examination of DMA Testing of Polymer Matrix Composites," J. Reinforced Plast Compos., DOI:10.1177/0731684407087740 (2008).
12. G.W. Ehrenstein, G. Riedel, and P. Trawiel, Thermal Analysis of Plastics: Theory and Practice, Hanser Gardner, Cincinnati, OH (2004).
13. I.M. Daniel and O. Ishai, Engineering Mechanics of Composite Materials, 2nd ed., Oxford University Press, New York (2005).
14. K.N. Shivakumar and C.C. Poe, "A Large Deformation GII Expression for Transversely Loaded Delaminated Beams," AIAA Paper 95-1280 (1990).
15. M.A. Hanna, "Strain Energy Release Rate in Delaminated Beams and Circular plates Subjected to Transverse Loads," M.S. Thesis, North Carolina Agricultural and Technical State University, Greensboro, NC (2003).
16. Annual Book of ASTM Standards, ASTM International, E1640-04, West Conshohocken, PA, 14.02 (2004).
17. Department of Defense, Handbook: Composite Materials Handbook, Vol. 2 of 5, MIL-HDBK-17-2E, Department of Defense, Washington, DC (2002).
18. Product Data Sheet, 3501-6 Epoxy Matrix, Hexcel Corporation, CA, USA.
19. S. Matsuda and M. Hojo, JSME Int J Ser A, 42, 421 (1999).