Study on Warpage Behavior and Filler Orientation during Injection Molding

International Polymer Processing

Volumn 23, Issue 5, 2008, Pages 419-429

  Michii, T ^a   Seto, M ^a   Yamabe, M ^a   Kubota, Y ^b   Aoki, G ^b   Ohtsuka, H ^b  

^a KANAZAWA INSTITUTE OF TECHNOLOGY   (Japan)

^b Polyplastics co   (Japan)

Author keywords

[No Author keywords available]

Indexed keywords

EID: 67649183096     PISSN: 0930777X     EISSN: None     Source Type: Journal    
DOI: 10.3139/217.0064     Document Type: Article

References (16)

1. Advani, S. G., Tucker III, C. L., "The Use of Tensors to Describe and Predict Fiber Orientation in Short Fiber Composites", J. Rheol., 31, 751-784(1987)
2. Agarwal, B. A., Broutman, L. J.: Analysis and Performance of Fiber Composites. Wiley-Interscience, New York, Chichester, Brisbane, Toronto (1980)
3. Fujita, A., et al., "Estimation of Mechanical Properties of Injection Molded CF/LCP Thin Plates Using Fiber Orientation Distributions", J. Japan Society of Polym. Process. 13, 701-703 (2001)
4. Jackson, W. C., et al., "Predicting the Orientation of Short Fibers in Thin Compression Moldings", J. Compos. Mater., 20, 539-557 (1986)
5. Kikuchi, H., Koyama, K., "Anisotropy of Linear Thermal Expansion Coefficient of a Disk Injection Molded from Reinforced PA66", J. Japan Society of Polym. Process. 5, 129-133 (1993)
6. Kikuchi, H., Koyama, K., "Generalization of Warpage for Anisotropic and Isotropic Parts", J. Japan Society of Polym. Process. 7, 63 - 68 (1995)
7. Kubota, Y., et al., "The Investigation and Evaluation of a CAE War- page Analysis for PBT with Composite Fillers", Japan Society of Polym. Process., 15th Annual Meeting, Tokyo, June (2004)
8. Mavridis, H., et al., "The Effect of Fountain Flow on Molecular Orientation in Injection Molding", J. Rheol., 32, 639-663 (1988)
9. Michii, T., et al., "Evaluation of Anisotropic Shrinkage due to Filler Orientation during Injection Molding", Japan Society of Polym. Process., 15th Annual Meeting, Tokyo, June (2004a)
10. Michii, T., et al., "Warpage Mechanism due to Fiber Orientation during Injection Molding", J. Japan Society of Polym. Process. 16, 467 - 473 (2004b)
11. Ogawa, T., et al.,"Fiber Orientation and Mechanical Properties for Molded Articles of Carbon Fiber Reinforced Nylon 66", J. Japan Society of Polym. Process. 8, 739-743 (1996)
12. Sanomura, Y., "Fiber Orientation Control of Short-Fiber Reinforced Thermoplastics by Extrusion and Prediction of Young's Modulus", J. Japan Society for Composite Materials, 27, 161 -166 (2001)
13. Seto, M., et al., "Method of Predicting the Distribution of Material Properties during Injection Molding V - Thermal Shrinkage Analy-sis Considering the Distribution of Thermal Expansion Coefficient", J. Japan Society of Polym. Process. 16, 548-553 (2004)
14. Seto, M., Yamabe, M., "Method of Predicting the Distribution of Material Properties During Injection Molding (I) - Thermal Expansion Coefficient Distribution Caused by the Flow Process", J. Japan Society of Polym. Process., 13, 812-817 (2001)
15. Yamashita, K., et al., "Analysis of Layered Structure Distinguished by Fiber Orientation in Injection Molding (1) - Effect of Thermal Expansion Coefficient on Warpage Deformation Behavior", J. Japan Society of Polym. Process. 13, 402-407 (2001)
16. Zhu, Y. T., et al., "Determination of Non-Symmetric 3-D Fiber-Orientation Distribution and Average Fiber Length in Short-Fiber Composites", J. Compos. Mater., 31, 1287-1301 (1997)