Sliding wear behaviour of a cast iron as affected by test environment and applied load

Industrial Lubrication and Tribology

Volumn 61, Issue 3, 2009, Pages 161-172

  Prasad, B K ^a  

^a REGIONAL RESEARCH LABORATORY CSIR   (India)

Author keywords

Friction; Iron; Lubrication; Oils; Wear

Indexed keywords

APPLIED LOADS; CONCENTRATION OF; CRITICAL CONCENTRATION; DEBRIS PARTICLES; DESIGN/METHODOLOGY/APPROACH; ENGINEERING APPLICATIONS; EXPERIMENTAL CONDITIONS; FRICTION COEFFICIENTS; FRICTIONAL HEATING; GRAPHITE PARTICLES; GREY CAST IRON; MATERIAL REMOVAL MECHANISMS; OILS; SLIDING WEAR BEHAVIOUR; SLIDING WEAR RESPONSE; SUBSURFACE DEFORMATION; SUBSURFACE REGIONS; TEST CONDITION; TEST ENVIRONMENT; WEAR; WEAR CHARACTERISTICS; WEAR PERFORMANCE; WEAR RATES; WEAR RESPONSE; WEAR SURFACE;

CAST IRON; CONCENTRATION (PROCESS); DEBRIS; FRICTION; GRAPHITE; HEATING; IRON RESEARCH; LEAD; METAL RECOVERY; POLYCRYSTALLINE MATERIALS; TRIBOLOGY; WEAR OF MATERIALS;

SOLID LUBRICANTS;

EID: 67649120029     PISSN: 00368792     EISSN: None     Source Type: Journal    
DOI: 10.1108/00368790910953686     Document Type: Article

References (47)

1. Angus, H.T. (Ed.) (1976), Cast Iron: Physical and Engineering Properties, 2nd ed., Butterworths, London, pp. 1-33.
2. Angus, H.T. and Lamb, A.D. (1957), "Lubrication behaviour of liquid metals", paper presented at I. Mech. Eng. Conf. on Lubrication and Wear, London.
3. ASM (1990), Metals Handbook, 10th ed., Vol. 1, ASM, Materials Park, OH, pp. 1-32.
4. ASM (1992), Metals Handbook, 10th ed., Vol. 18, ASM, Materials Park, OH, pp. 98-122, 695-701.
5. Bhushan, B. and Gupta, B.K. (Eds) (1991), Handbook of Tribobgy, McGraw-Hill, New York, NY, pp. 5.1-5.86.
6. Brendle, M., Falkin, J., Turgis, P. and Gilmore, R. (1990), "Mechanisms of graphite transfer on steel as studied by image analysis", STLE Tribo. Trans., Vol. 33 No. 4, pp. 471-80.
7. Child, T.H.C. and Sabbagh, F. (1989), "Boundary-lubricated wear of cast irons to simulate automotive piston ring wear rates", Wear, Vol. 134, pp. 81-97.
8. Cho, M.H., Kim, S.J., Basch, R.H., Fash, J.M. and Jang, H. (2003), "Tribological study of gray cast iron with automotive brake linings: the effect of rotor microstructure", Tribo. Int., Vol. 36, pp. 537-45.
9. Das, S., Prasad, S.V. and Ramachandran, T.R. (1989), "Microstructure and wear of cast Al-Si alloy graphite composites", Wear, Vol. 133, pp. 173-87.
10. Das, S., Prasad, S.V. and Ramachandran, T.R. (1991), "Tribology of Al-Si alloy-graphite composites: triboinduced graphite films and the role of silicon morphology", Mater. Sci. Eng. A, Vol. 138A, pp. 123-32.
11. Eyre, T.S. and Fitter, C. (1983), "Application of oil analysis technique to the study of cylinder liner wear", Wear, Vol. 90, pp. 31-7.
12. Gulyaev, A.G. (Ed.) (1980), Physical Metallurgy, Vol. I, Mir Publishers, Moscow, pp. 175-97.
13. Humphries, J.G. (1961), "Effect of composition on the liquidus and eutectic temperatures and on the eutectic point of cast irons", BCIRAJ, Vol. 9, pp. 609-21.
14. Jha, A.K., Prasad, S.V. and Upadhyaya, G.S. (1988), "Dry sliding wear of sintered 6061 aluminium alloy based particulate composites containing solid lubricants", in Kingsbury, G.R. (Ed.), Proc. Wear Resistance of Metals and Alloys, Chicago, IL, USA, 24-30 September, ASM, Materials Park, OH, pp. 73-80.
15. Jha, A.K., Prasad, S.V. and Upadhyaya, G.S. (1989), "Sintered 6061 aluminium alloy-solid lubricant particle composites: sliding wear and mechanisms of lubrication", Wear, Vol. 133, pp. 163-72.
16. Jha, A.K., Prasad, B.K., Modi, O.P., Das, S. and Yegneswaran, A.H. (2003), "Correlating microstructural features and mechanical properties with abrasion resistance of a high strength low alloy steel", Wear, Vol. 254 Nos 1/2, pp. 120-8.
17. Kennedy, F.E. Jr (1984), "Thermal and thermomechanical effects in dry sliding", Wear, Vol. 100, pp. 453-76.
18. Lancaster, J. (1966), "Anisotropy in the mechanical properties of lamellar solids and its effect on wear and transfer", Wear, Vol. 9, pp. 169-88.
19. Lancaster, J. (1975), "Instabilities in the frictional behaviourb of carbons and graphites", Wear, Vol. 34, pp. 275-90.
20. Langlade, C., Fayeulle, S. and Olier, R. (1993), "Characterization of graphite superficial thin films achieved during friction", Appl. Surf. Sci., Vol. 65/66, pp. 83-9.
21. Langlade, C., Fayeulle, S. and Olier, R. (1994), "New insights into adhesion and lubricating properties of graphite-based transfer films", Wear, Vol. 172, pp. 85-92.
22. Liu, Y.B., Rohatgi, P.K. and Ray, S. (1993), "Tribological characteristics of aluminum-50 vol% graphite composite", Metall. Trans. A, Vol. 24A, pp. 151-8.
23. Liu, Y.B., Lim, S.C., Ray, S. and Rohatgi, P.K. (1992), "Friction and wear of Al-graphite composite: smearing process of graphite during sliding", Wear, Vol. 159, pp. 201-5.
24. Masjuki, H.H. and Maleque, M.A. (1996), "The effect of palm oil diesel fuel contaminated lubricant on sliding wear of cast irons against mild steel", Wear, Vol. 198, pp. 293-9.
25. Mazumdar, B.C. (1996), Introduction to Tribobgy of Bearings, A.H. Wheeler & Co. Pvt. Ltd, New Delhi, pp. 12-22.
26. Mazumdar, B.S., Yegneswaran, A.H. and Rohatgi, P.K. (1984), "Strength and fracture behaviour of metal matrix particulate composites", Mater. Sci. Eng., Vol. 68, pp. 85-96.
27. Montgomery, R.S. (1969), "The mild wear mechanism of nodular iron", Wear, Vol. 13, pp. 337-43.
28. Nakamura, Y. and Hirayama, S. (1989), "Wear tests of grey cast iron against ceramics", Wear, Vol. 132, pp. 337-45.
29. Pandey, J.P. and Prasad, B.K. (1998), "Dry sliding wear behaviour of a zinc-based alloy: a comparative study with a leaded-tin bronze", Mater. Trans. JIM, Vol. 38, pp. 1121-5.
30. Prasad, B.K. (1991), "Abrasion induced microstructural changes during low stress abrasion of a plain carbon (0.5%C) steel", Wear, Vol. 151, pp. 1-12.
31. Prasad, B.K. and Das, S. (1991), "The significance of the matrix microstructure on the solid lubrication characteristics of graphite in aluminium alloys", Mater. Sci. Eng. A, Vol. 144A, pp. 229-35.
32. Prasad, B.K., Patwardhan, A.K. and Yegneswaran, A.H. (1996), "Characterization of the wear response of a modified zinc-based alloy vis-à-vis conventional zinc-based alloy and a bearing bronze at a high sliding speed", Metall. Mater. Trans. A, Vol. 27A, pp. 3513-23.
33. Prasad, B.K., Patwardhan, A.K. and Yegneswaran, A.H. (1998), "Microstructure and property characterization of a modified zinc-base alloy and comparison with bearing alloys", J. Mater. Eng. Perf., Vol. 7, pp. 130-5.
34. Prasad, S.V. and McConnell, B.D. (1991), "Tribology of aluminium metalmatrix composites lubricated by graphite", Wear, Vol. 149, pp. 241-53.
35. Prasad, S.V. and Rohatgi, P.K. (1987), "Tribological properties of Al alloy particle composites", J. Met., Vol. 39, pp. 22-6.
36. Rac, A. (1985), "Influence of load and speed on wear characteristics of grey cast iron in dry sliding - selection for minimum wear", Tribo. Int., Vol. 18, pp. 29-33.
37. Rayiko, M.V. and Dmytrychenko, N.F. (1988), "Some aspects of boundary lubrication in the local contact of friction surfaces", Wear, Vol. 126, pp. 69-78.
38. Rigney, D.A., Chen, L. H., Naylor, M.G.S. and Rosenfield, A.R. (1984), "Wear processes in sliding systems", Wear, Vol. 100, pp. 195-219.
39. Rohatgi, P.K., Asthana, R. and Das, S. (1986), "Solidification, structure and properties of metal-ceramic particle composites", Int. Met. Rev., Vol. 31, pp. 115-39.
40. Rohatgi, P.K., Liu, Y and Barr, T.L. (1991), "Tribological behaviour and structural analysis of tribodeformed Al alloy-50 pet graphite particle composites", Metall. Trans. A, Vol. 22A, pp. 1435-41.
41. Rohatgi, P.K., Ray, S. and Liu, Y. (1992), "Tribological properties of metal matrix graphite particle composites", Int. Mater. Rev., Vol. 37, pp. 129-49.
42. Rowe, G. (1960), "Some observations on the frictional behaviour of boron. Nitride and graphite", Wear, Vol. 3, pp. 274-85.
43. Sugishita, J. and Fujiyoshi, S. (1981), "The effect of cast iron graphite on friction and wear performance. I: Graphite film formation on grey cast iron surfaces", Wear, Vol. 66, pp. 209-21.
44. Takeuchi, E. (1970), "The mechanism of sliding wear of lubricated flake graphite cast iron", Wear, Vol. 15, pp. 201-8.
45. Takeuchi, E. (1972), "The mechanism of wear of spheroidal graphite cast iron in dry sliding", Wear, Vol. 19, pp. 267-76.
46. Wilson, F. and Eyre, T.S. (1973), "Addition of graphite particles to oil lubricants", Lub. Eng., Vol. 29, pp. 65-72.
47. Zhang, Y., Chen, Y., He, R. and Shen, B. (1993), "Investigation of tribological properties of brake shoe materials - phosphorous cast irons with different graphite morphologies", Wear, Vol. 166 No. 2, pp. 179-86.