Identification of effective zones for high pressure coolant in milling

CIRP Annals - Manufacturing Technology

Volumn 49, Issue 1, 2000, Pages 47-52

  Rahman, M ^a   Senthil Kumar, A ^a   Choudhury, M R ^a  

^a NATIONAL UNIVERSITY OF SINGAPORE   (Singapore)

Author keywords

[No Author keywords available]

Indexed keywords

COOLANTS; CUTTING FLUIDS; CUTTING TOOLS; FAILURE ANALYSIS; STEEL; TUNGSTEN CARBIDE; WEAR OF MATERIALS;

HIGH PRESSURE COOLANTS;

MILLING (MACHINING);

EID: 6744259047     PISSN: 00078506     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0007-8506(07)62893-5     Document Type: Article

References (12)

1. Pigott, R. J. S., Colwell, A. T., 1952, Hi-Jet System for Increasing Tool Life, SAE Q. Trans., 6/3:547-566.
2. Sharma, C. S., Rice, W.B., Salmon, R , 1971, Some Effects of Injecting Cutting Fluids Directly into the Chip-Tool Interface, J. of Engng Ind, Trans. ASME, 93:441-444.
3. Nagpal, B. K., Sharma, C. S., 1973, Cutting Fluid Performance - Part 1 - Optimization of Pressure for Hi-Jet Method of Cutting Fluid Application, J. of Engng Ind, Trans. ASME, 95:881-889.
4. Kurimoto, T., Barrow, G., 1982, The Influence of Aqueous Fluid on the Wear Characteristics and Life of Carbide Cutting Tool, Annals of the CIRP, 31/1:19-23.
5. Wertheim, R., Rotberg, J., Ber, A., 1992, Influence of High-Pressure Flushing Through the Rake Face of the Cutting Tool, Annals of the CIRP, 41/1:101-106.
6. Ezugwu, E. O., Machado, A. R., Pasby, I. R., Wallbank, J., 1990, The Effect of High-Pressure Coolant Supply When Machining a Heat Resistant Nickel-Based Superalloy, J. of Society of Trib. & Lub. Engineers, 47/9:751-757.
7. Machado, A. R., Wallbank, J., 1994, The Effects of a High Pressure Coolant Jet on Machining, J. of Engng Manufacture, 208:29-38.
8. Machado, A. R., Wallbank, J., Pasby, I. R., Ezugwu, E. O., 1998, Tool Performance and Chip Control when Machining Ti6Al4V and Inconel 901 Using High Pressure Coolant Supply, Machining Science and Technilogy, 2/1:1-12.
9. Rasch, F.O., Vigeland, T., 1981, Hydraulic Chip Breaking, Annals of the CIRP, 30/1:333-335.
10. Kovacevic, R., Mohon, R., Cherukuthota, C., 1993, High Pressure Waterjet as a Coolant/Lubricant in Milling Operation, Manufacturing Science and Engng, PED, ASME Winter Annual Meeting, 64:733-748.
11. Kovacevic, R., Cherukuthota, C., Mazurkiewicz, M., 1995, High Pressure Waterjet Cooling/Lubrication to Improve Machining Efficiency in Milling, International J. of Machine Tools and Manufacture, 35/10:1459-1473.
12. Kovacevic, R., Cherukuthota, C., Mohon, R., 1995, Improving Milling Performance with High Pressure Waterjet Assisted Cooling/Lubrication, J. of Engng Ind, Trans. ASME, 117/3:331-339.