The recovery of design intent in reverse engineering problems

Computers and Industrial Engineering

Volumn 56, Issue 4, 2009, Pages 1265-1275

  Barbero, Basilio Ramos ^a  

^a UNIVERSITY OF BURGOS   (Spain)

Author keywords

Constraints; Design intent; Design recovery; Parametric approximation; Reverse engineering

Indexed keywords

CAD SOFTWARES; CONSTRAINTS; DESIGN INTENT; DESIGN RECOVERY; ENGINEERING PROBLEMS; GENERAL KNOWLEDGE; MATHEMATICAL ALGORITHMS; PARAMETRIC APPROXIMATION; POINT CLOUDS; SUCCESSIVE APPROXIMATIONS;

APPROXIMATION ALGORITHMS; COMPUTER AIDED DESIGN; REENGINEERING; REVERSE ENGINEERING;

KNOWLEDGE ENGINEERING;

EID: 67349272597     PISSN: 03608352     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.cie.2008.07.023     Document Type: Article

References (20)

1. AENOR (2000). UN-EN ISO 10360-1. Especificación geométrica de productos (GPS). Ensayo de aceptación y verificación periódica de maquinas de medición por coordenadas (MMC). Parte 1: Vocabulario.
2. Bae S.-H., and Choi B.-K. NURBS surface fitting using orthogonal coordinate transform for rapid product development. Computer-Aided Design 34 (2002) 683-690
3. Carbone V., Carocci M., Sabio E., Sansoni G., and Chiffre L. Combination of vision system and a coordinate measuring machine for the reverse engineering of freeform surfaces. The International Journal of Advanced Manufacturing Technology 17 (2001) 263-271
4. Chikofsky E.J., and Cross II J.H. Reverse engineering and design recovery: A taxonomy. IEEE Software 7 (1990) 13-17
5. Cohen-Steiner D., Alliez P., and Desbrun M. Variational shape approximation. ACM Transactions on Graphics 23 3 (2004) 905-914
6. Huang W., Kong Z., Ceglarek D., and Brahmst E. The analysis of feature-based measurement error in coordinate metrology. IIE Transactions 36 (2004) 237-251
7. Huang M.-C., and Tai C.-C. The pre-processing of data points for curve fitting in reverse engineering. The International Journal of Advanced Manufacturing Technology 16 (2000) 635-642
8. Knopf G.-K., and Naji R.-A. Adaptive reconstruction of bone geometry from serial cross-sections. Artificial Intelligence in Engineering 15 (2001) 227-234
9. 1 continuity of B-spline surface patches in reverse engineering. Computer-Aided Design 27 6 (1995) 471-478
10. Mohangegh K., Sadeghid MH., and Abdulla A. Reverse engineering of turbine blades based on design intent. International Journal of Advanced Manufacturing Technology 32 9-10 (2007) 1009-1020
11. Piegl L.A., and Tiller W. Parametrization for surface fitting in reverse engineering. Computer-Aided Design 33 (2001) 593-603
12. Sarkar B., and Menq C.-H. Smooth-surface approximation and reverse engineering. Computer-Aided Design 23 9 (1991) 623-628
13. Sarkar B., and Menq C.-H. Parameter optimization in approximating curves and surfaces to measurement. Computer Aided Geometric Design 8 (1991) 267-290
14. Tai C.-C., and Huang M.-C. The processing of data points basing on design intent in reverse engineering. International Journal of Machine Tools & Manufacture 40 (2000) 1327-1913
15. Thompson W.B., et al. Feature-based reverse engineering of mechanical parts. IEEE Transactions on Robotics and Automation 15 1 (1999) 57-66
16. Ueng W.-D., and Lai L.-Y. A sweep-surface fitting algorithm for reverse engineering. Computer in Industry 35 (1998) 261-273
17. Ueng W.-D., Lai L.-Y., and Doong J.-L. Sweep-surface reconstruction from three-dimensional measured data. Computer-Aided Design 30 10 (1998) 791-805
18. Várady T., et al. Reverse engineering of geometric models - an introduction. Computer-Aided Design 29 4 (1997) 255-268
19. Weiyin M., and Kruth J.P. Parameterization of randomly measured points for least squares fitting of B-spline curves and surfaces. Computer-Aided Design 27 9 (1995) 663-675
20. Yau H.-T. Uncertainty analysis in geometric best fit. International Journal of Machine Tools & Manufacture 38 (1998) 1323-1342