Numerical investigations on sheet metal blanking with high speed deformation

Materials and Design

Volumn 30, Issue 9, 2009, Pages 3566-3571

  Marouani, H ^a   Ben Ismail, A ^b   Hug, E ^c   Rachik, M ^b  

^a UNIVERSITY OF MONASTIR   (Tunisia)

^b CNRS   (France)

^c LABORATOIRE CRISMAT   (France)

Author keywords

Damage; Numerical simulation; Rate dependent plasticity; Sheet metal blanking

Indexed keywords

BLANKING PROCESS; CONSTITUTIVE LAW; CUT EDGE; DAMAGE; EXPERIMENTAL DATA; FERROMAGNETIC SHEETS; FRICTIONAL CONTACT; GEOMETRIC CONFIGURATIONS; HIGH-SPEED DEFORMATION; MATERIAL TESTING; MECHANICAL STATE; NON-ORIENTED; NUMERICAL INVESTIGATIONS; NUMERICAL RESULTS; NUMERICAL SIMULATION; PUNCH PENETRATION; PUNCH SPEED; RATE DEPENDENT; RATE DEPENDENT PLASTICITY; ROTATING ELECTRICAL MACHINES; SHEARING PROCESS; SHEET METAL BLANKING; TENSILE TESTS;

CONSTITUTIVE MODELS; MAGNETIC PROPERTIES; MAGNETIC TAPE; METALS; PLASTICITY; PUNCHING; SHEARING MACHINES; SIMULATORS; STRAIN RATE; TENSILE TESTING;

SHEET METAL;

EID: 67349133440     PISSN: 02641275     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.matdes.2009.02.028     Document Type: Article

References (32)

1. Sinram K., Grafen A., Janzon K., and Weber K. The influence of fine blanking on the magnetic properties of soft magnetic steel. IEEE Trans Magn 24 (1988) 839-842
2. Hubert O., and Hug E. Influence of plastic strain behaviour of non-oriented Fe-3Si and application to manufacturing test by punching. Mater Sci Technol 11 (1995) 482-487
3. Hancock R.G. Effect of stress relief annealing on the magnetic properties of cut laminations and assembled cores produced from nonoriented electrical steel. J Magn Magn Mater 19 (1979) 65-68
4. Kim D.H., Lee S.B., Ko D.C., and Kim B.M. Process design and forming analysis of a permalloy shielding can for instrument clusters. J Mater Process Technol 135 (2003) 366-374
5. Aggarwal S., Bhushan B., and Katsube N. Three-dimensional finite element analysis of the magnetic tape slitting process. Mater Process Technol 170 (2005) 71-88
6. Ossart F., Hug E., Hubert O., Buvat C., and Billardon R. Effect of punching on electrical steels: experimental and numerical coupled analysis. IEEE Trans Magn 36 (2000) 3137-3140
7. Choi J.C., and Kim C. A compact and practical CAD/CAM system for the blanking or piercing of irregular shaped-sheet metal products for progressive working. J Mater Process Technol 110 (2001) 36-46
8. Kleber X., and Vincent A. On the role of residual internal stresses and dislocations on Barkhausen noise in plastically deformed steel. NDT & E Int 37 (2004) 439-445
9. Stewart D.M., Stevens K.J., and Kaiser A.B. Magnetic Barkhausen noise analysis of stress in steel. Curr Appl Phys 4 (2004) 308-311
10. Moorthy V., Shaw B.A., and Hopkins P. Surface and subsurface stress evaluation in case-carburised steel using high and low frequency magnetic Barkhausen emission measurements. J Magn Magn Mater 299 (2006) 362-375
11. Moorthy V., Shaw B.A., and Hopkins P. Magnetic Barkhausen emission technique for detecting the overstressing during bending fatigue in case-carburised En36 steel. NDT & E Int 38 (2005) 159-166
12. Jana S., and Ong N.S. Effect of punch clearance in the high-speed blanking of thick metals using an accelerator designed for a mechanical press. J Mech Work Technol 19 (1998) 55-72
13. Thiruvarudchelvan S., and Ong N.S. Exploration of the piercing of round holes in metal sheets in the presence of frictionally induced radial compressive stress. J Mater Process Technol 23 (1990) 295-310
14. Li M. An experimental investigation on cut surface and burr in trimming aluminum autobody sheet. Int J Mech Sci 42 (2000) 889-906
15. Maiti S.K., Ambekar A.A., Singh U.P., Date P.P., and Narasimhan K. Assessment of influence of some process parameters on sheet metal blanking. J Mater Process Technol 102 (2000) 249-256
16. Taupin E., Breitling J., Wu W.T., and Atlan T. Material fracture and burr formation in blanking results of FEM simulations and comparison with experiments. J Mater Process Technol 59 (1996) 68-78
17. Brokken D., Brekelmans W.A.M., and Baaijens F.T.P. Predicting the shape of blanked products: a finite element approach. J Mater Process Technol 103 (2000) 51-56
18. Goijaerts A.M., Govaert L.E., and Baaijens F.T.P. Evaluation of ductile fracture models for different metal in blanking. J Mater Process Technol 110 (2001) 312-323
19. Vaz J.M., and Owen D.R.J. Aspects of ductile fracture and adaptive mesh refinement in damaged elasto-plastic materials. Int J Numer Meth Eng 50 (2000) 29-54
20. Rachik M., Roelandt J.M., and Maillard A. Some phenomenological computational aspects of sheet metal blanking simulation. J Mater Process Technol 128 (2000) 256-265
21. Chan L.C., Leung Y.C., Lee T.C., Fan J.P., and Tang C.Y. Numerical simulation for fine-blanking - a new approach. Mater Sci Eng A 364 (2004) 207-215
22. Mediavilla J., Peerlings R.H.J., and Geers M.G.D. An integrated continuous-discontinuous approach towards damage engineering in sheet metal forming processes. Eng Fract Mech 73 (2006) 895-916
23. Stegeman Y.W., Goijaerts A.M., Brokken D., Brekelmans W.A.M., Govaert L.E., and Baaijens F.P.T. An experimental and numerical study of a planar blanking process. J Mater Process Technol 87 (1997) 266-276
24. Peirce D., Shih C.F., and Needleman A. A tangent modulus method for rate dependent solids. Compos Struct 18 (1979) 875-887
25. G'sell C., and Jonas J.J. Determination of the plastic behaviour of solid polymers at constant true strain rate. J Mater Sci 14 (1979) 583-591
26. Addiego F., Dahoun A., G'Sell C., and Hiver J.M. Characterization of volume strain at large deformation under uniaxial tension in high-density polyethylene. Polymer 47 (2006) 4387-4399
27. Gurson A L. Continuum theory of ductile rupture by void nucleation and growth: Part I. Yield criteria and flow rules for porous ductile materials. J Eng Mater Technol 99 (1977) 2-15
28. Tvergaard V. Influence of voids on shear band instabilities under plane strain condition. Int J Fract Mech 17 (1981) 389-407
29. Chu C.C., and Needleman A. Void nucleation effects in biaxially stretched sheets. J Eng Mater Technol 102 (1980) 249-256
30. Borst D.R., and Mühlhaus H.B. Gradient-dependent plasticity: formulation and algorithmic aspects. Int J Numer Meth Eng 35 (1992) 521-539
31. Needleman A. Material rate dependence and mesh sensitivity in localization problems. Comput Meth Appl Mech Eng 67 (1988) 69-86
32. Daly D., Duroux P., Rachik M., Roelandt J.M., and Wilsius J. Modelling of the post-localization behaviour in tube hydroforming of low carbon steels. J Mater Process Technol 182 (2007) 248-256