Microscopic phase-dependent residual stresses in the machined surface layer of two-phase alloy

Journal of Materials Processing Technology

Volumn 209, Issue 9, 2009, Pages 4496-4501

  Obikawa, T ^a   Takemura, Y ^b   Akiyama, Y ^b   Shinozuka, J ^c   Sasahara, H ^d  

^a INSTITUTE OF INDUSTRIAL SCIENCE   (Japan)

^b TOKYO INSTITUTE OF TECHNOLOGY   (Japan)

^c IBARAKI UNIVERSITY   (Japan)

^d TOKYO UNIVERSITY OF AGRICULTURE AND TECHNOLOGY   (Japan)

Author keywords

Cutting; FE modeling; Machined surface; Microstructure; Residual stress; Two phase alloy

Indexed keywords

AEROSPACE ENGINES; CARBON CONTENTS; CRITICAL STRESS; CUTTING FORCES; FATIGUE-CRACK NUCLEATIONS; FE MODELING; FINITE ELEMENTS; FINITE-ELEMENT MODELING; IN CHIPS; IRON AND STEELS; MACHINED SURFACE; PHASE ALLOYS; RESIDUAL STRESS DISTRIBUTIONS; STRESS CORROSIONS; TENSILE SURFACES; TWO-PHASE ALLOY; WORK MATERIALS; WORK PIECES;

ALLOYS; CERIUM ALLOYS; CORROSION FATIGUE; CRACKING (CHEMICAL); CRACKS; FERRITE; GAS ENGINES; GAS TURBINES; MACHINING; MICROSTRUCTURE; PEARLITE; REAL TIME SYSTEMS; STRENGTH OF MATERIALS; STRESS CONCENTRATION; STRESS CORROSION CRACKING; SURFACES;

RESIDUAL STRESSES;

EID: 64249123911     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmatprotec.2008.10.039     Document Type: Article

References (12)

1. Childs T.H.C., Maekawa K., Obikawa T., and Yamane Y. Metal Machining-Theory and Application (2000), Arnold, London
2. Nasr M.N.A., Ng E.G., and Elbestawi M.A. Modelling the effects of tool-edge radius on residual stresses when orthogonal cutting AISI 316L. Int. J. Mach. Tools Manuf. 47 (2007) 401-411
3. Obikawa T., and Usui E. Computational machining of titanium alloy-finite element modeling and a few results. J. Manuf. Sci. Eng. 118 (1996) 208-215
4. Obikawa T., Sasahara H., Shirakashi T., and Usui E. Application of computational machining method to discontinuous chip formation. J. Manuf. Sci. Eng. 119 (1997) 667-674
5. Salio M., Berruti T., and De Poli G. Prediction of residual stress distribution after turning in turbine disks. Int. J. Mech. Sci. 48 (2006) 976-984
6. Sasahara H., Obikawa T., and Shirakashi T. FEM analysis of cutting sequence effect on mechanical characteristics in machined layer. J. Mater. Proc. Technol. 62 (1996) 448-453
7. Sasahara H., Obikawa T., and Shirakashi T. FEM simulation on machining process of two phase alloy. In: Liao Y.S., and Ueda N. (Eds). Proceedings of ICPE'97. Taipei, Taiwan (1997) 467-472
8. Sasahara H., and Obikawa T. FEM simulation on cutting process of two phase alloys. J. Jpn. Soc. Prec. Eng. 64 (1998) 1083-1087 (in Japanese)
9. Sasahara H., Obikawa T., and Shirakashi T. Prediction model of surface residual stress within a machined surface by combining two orthogonal plane models. Int. J. Mach. Tools Manuf. 44 (2004) 815-822
10. Shinozuka J., Obikawa T., and Li C. Ultra high-speed metal cutting mechanism with shock waves. Trans. Jpn. Soc. Mech. Eng. (C) 69 (2003) 1123-1130 (in Japanese)
11. Shinozuka J., and Obikawa T. High levels of hydrostatic stress at shear zone induced by plastic shock waves under ultra high-speed cutting conditions. In: Micari F., Jawahir I.S., and Filice L. (Eds). Proceedings of 10th CIRP International Workshop on Modeling of Machining Operation. Reggio Calabria, Italy (2007) 357-364
12. Simoneau A., Ng E., and Elbestawi M.A. Surface defects during microcutting. Int. J. Mach. Tools Manuf. 46 (2006) 467-481