Effect of entrance nozzle design on the fluid flow in an ingot mold during filling

ISIJ International

Volumn 44, Issue 8, 2004, Pages 1358-1365

  Eriksson, Robert ^a   Jonsson, Lage ^a   Jönsson, Pär G ^a  

^a ROYAL INSTITUTE OF TECHNOLOGY   (Sweden)

Author keywords

CFD; Fluid flow; Inlet geometry; Large eddy simulation; Mold filling; Up hill teeming

Indexed keywords

COMPUTATIONAL FLUID DYNAMICS; FILLING; INGOT MOLDS; MATHEMATICAL MODELS; NOZZLES; POWDERS; PRODUCT DESIGN; STEEL;

FREE SURFACES; INLET GEOMETRY; MOLD FILLING; UP-HILL TEEMING;

FLOW OF FLUIDS;

EID: 6344229854     PISSN: 09151559     EISSN: None     Source Type: Journal    
DOI: 10.2355/isijinternational.44.1358     Document Type: Article

References (18)

1. P. Sjödin, P. Jönsson, M. Andreasson and A. Winquist: Scand. J. Metall., 26 (1991), 41.
2. R. Eriksson, P. Jönsson and A. Gustafsson: Scand. J. Metall., 33 (2004), 160.
3. J. Chang, R. Eriksson and P. Jönsson: Ironmaking Steelmaking, 30 (2003), No. 1, 66.
4. M. Freborg: Proc. 50th Electric Furnace Conf., ISS, Warrendale, PA, (1992), 235.
5. P. Jönsson, N. Saluja, O. J. Ilegbusi and J. Szekely: AFS Trans., 99 (1991), 291.
6. G. B. van der Graaf, H. E. A. van der Akker and L. Katgerman: Metall. Mater. Trans. B, 32B (2001), 69.
7. R. Eriksson, L. T. I. Jonsson and P. G. Jönsson: Tech. Rep. ISRN MSE/KTH-03/24-SE+TILL.METALLURGI/RAPP, Dept. of Material Science and Engineering, KTH, Stockholm, Sweden, (2003).
8. R. Eriksson, A. Tilliander, L. T. I. Jonsson and P. G. Jönsson: Steel Res., 74 (2003), 423.
9. J. R. Blank: Proc. 67th Steelmaking Conf., ISS, Warrendale, PA, (1984), 135.
10. M. Petersson: Final report, tech. rep., Jernkontoret, Stockholm, Sweden, (1976). TM 25/76.
11. Flow3D Manual version 8.0, Flow Science inc., SantaFe, NM, (2003).
12. C. W. Hirt and B. D. Nicholas: J. Comp. Phys., 39 (1981), 201.
13. J. Smagorinsky: Monthly Weather Review, 91 (1963), 99.
14. J. W. Deardorff: Boundary-Layer Meteorology, 7 (1974), 81.
15. B. G. Thomas, Q. Yuan, S. Sivramkrishnan, T. Shi, S. P. Vanka and M. B. Assar: ISIJ Int., 41 (2001), No. 10, 1262.
16. Z. Xiao, Y. Peng and C. Liu: Chin. J. Mater. Sci. Technol., 3 (1987), 187.
17. L. Jonsson and P. Jönsson: ISIJ Int., 36 (1996), No. 9, 1127.
18. H. Gaye, D. Lucas, M. Olette and P. V. Riboud: Can. Metall. Q., 23 (1984), No. 2, 179.