Analysis of thermo-visco-plastic behaviour of six high strength steels

Materials and Design

Volumn 30, Issue 5, 2009, Pages 1748-1761

  Rusinek, A ^a   Rodriguez Martinez J A ^b   Klepaczko, J R ^a   Pecherski, R B ^c  

^a UNIVERSITÉ DE LORRAINE   (France)

^b UNIVERSIDAD CARLOS III DE MADRID   (Spain)

^c INSTITUTE OF FUNDAMENTAL TECHNOLOGICAL RESEARCH   (Poland)

Author keywords

[No Author keywords available]

Indexed keywords

AUSTENITIC; CONSTITUTIVE RELATIONS; DEFORMATION MODES; EXPERIMENTAL DATUM; HIGH STRENGTH STEELS; MICRO-MECHANISMS; PLASTIC BEHAVIOURS; PLASTIC PROPERTIES; STACKING FAULT ENERGIES; WORK HARDENINGS;

AUSTENITE; AUSTENITIC STEEL; DEFORMATION; FERRITE; STEEL; STEEL METALLOGRAPHY; STRAIN HARDENING; STRAIN RATE; STRENGTH OF MATERIALS;

FERRITIC STEEL;

EID: 60249097961     PISSN: 02641275     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.matdes.2008.07.034     Document Type: Article

References (64)

1. Børvik T., Hopperstad O.S., Berstad T., and Langseth M. A computational model of viscoplasticity and ductile damage for impact and penetration. Eur J Solid Mech A 20 (2001) 685-712
2. Nemat-Nasser S., and Guo W.G. Thermomechanical response of DH-36 structural steel over a wide range of strain rates and temperatures. Mech Mater. 35 (2003) 1023-1047
3. Fernández J., Illescas S., and Guilemany J.M. Effect of microalloying elements on the austenitic grain growth in a low carbon HSLA steel. Mater Lett 61 (2007) 2389-2392
4. de Sousa R.R.M., de Araújo F.O., Barbosa J.C.P., Ribeiro K.J.B., da Costa J.A.P., and Alves Jr. C. Nitriding using cathodic cage technique of austenitic stainless steel AISI 316 with addition of CH4. Mater Sci Eng A 487 (2008) 124-127
5. Invernizzi A.J., Sivieri E., and Trasatti S.P. Corrosion behaviour of duplex stainless steels in organic acid aqueous solutions. Mater Sci Eng A 485 (2008) 234-242
6. Bouaziz O., and Guelton N. Modelling of TWIP effect on work-hardening. Mater Sci Eng A 319-321 (2001) 246-249
7. Nemat-Nasser S., Guo W.G., and Kihl D.P. Thermomechanical response of AL-6XN stainless steel over a wide range of strain rates and temperatures. J Mech Phys Solids 49 (2001) 1823-1846
8. Lebedev A.A., and Kosarchuk V.V. Influence of phase transformations on the mechanical properties of austenitic stainless steels. Int J Plasticity 16 (2000) 749-767
9. Iwamoto T., Tsuta T., and Tomita Y. Investigation on deformation mode dependence of strain-induced martensitic transformation in TRIP steels and modeling of transformation kinetics. Int J Mech Sci 40 (1998) 173-182
10. Iwamoto T., and Tsuta T. Computational simulation of the dependence of the austenitic grain size on the deformation behaviour of TRIP steels. Int J Plasticity 16 (2000) 791-804
11. Taleb L., and Petit S. New investigations on transformation induced plasticity and its interaction with classical plasticity. Int J Plasticity 22 (2006) 110-130
12. Papatriantafillou I., Agoras M., Aravas N., and Haidemenopoulos G. Constitutive modeling and finite element methods for TRIP steels. Comput Meth Appl Mech Eng 195 (2006) 5094-5114
13. Meftah S., Barbe F., Taleb L., and Sidoroff F. Parametric numerical simulations of TRIP and its interaction with classical plasticity in martensitic transformation. Eur J Mech A Solids 26 (2007) 688-700
14. Huh H, Seok-Bong Kima SB, Songa JH, Lim JH. Dynamic tensile characteristics of TRIP-type and DP-type steel sheets for an auto-body. Int J Mech Sci. doi:10.1016/j.ijmecsci.2007.09.004.
15. Tomita Y., and Iwamoto T. Constitutive modelling of TRIP steel and its application to the improvement of mechanical properties. Int J Mech Sci 37 (1995) 1295
16. Mirzadeh H., and Najafizadeh A. Modeling the reversion of martensite in the cold worked AISI 304 stainless steel by artificial neural networks. Mater Design 30 (2009) 570-573
17. Eyercioglu O., Kanca E., Pala M., and Ozbay E. Prediction of martensite and austenite start temperatures of the Fe-based shape memory alloys by artificial neural networks. J Mater Process Technol 200 (2008) 146-152
18. Mirzadeh H., and Najafizadeh A. Correlation between processing parameters and strain-induced martensitic transformation in cold worked AISI 301 stainless steel. Mater Charact (2008) 10.1016/j.matchar.2008.03.004
19. Bouaziz O., Allain S., and Scott C. Effect of grain and twin boundaries on the hardening mechanisms of twinning-induced plasticity steels. Scripta Mater 58 (2008) 484-487
20. Allain S., Cugy P., Scott C., Château J.P., Rusinek A., and Deschamp A. The influence of the plastic instabilities on the mechanical properties of a high manganese austenitic FeMnC steel. Int J Mater Res 99 (2008) 734-738
21. Zhang F., Fu R., Qiu L., and Zheng Y. Microstructure and property of nitrogen-alloyed high manganese austenitic steel under high strain rate tension. Mater Sci Eng A (2008) 10.1016/j.msea.2008.03.026
22. Ueji R., Tsuchida N., Terada D., Tsuji N., Tanaka Y., Takemura A., and Kunishige K. Tensile properties and twinning behavior of high manganese austenitic steel with fine-grained structure. Scripta Mater (2008) 10.1016/j.scriptamat.2008.06.050
23. Meng L., Yang P., Xie Q., Ding H., and Tang Z. Dependence of deformation twinning on grain orientation in compressed high manganese steels. Scripta Mater 56 (2007) 931-934
24. Yang P., Xie Q., Meng L., Ding H.Z., and Tang Z. Dependence of deformation twinning on grain orientation in a high manganese steel. Scripta Mater 55 (2006) 629-631
25. Lecroisey F., and Pineau A. Martensitic transformations induced by plastic deformation in the Fe-Ni-Cr-C system. Metall Trans 3 (1972) 397
26. Rémy L. Kinetics of f.c.c deformation twinning and its relationship to stress-strain behaviour. Acta Metall 26 (1978) 443-451
27. Hong S.H., and Han Y.S. Effect of solution treatment on the stress-rupture property of MA ODS Ni-base superalloy. Scripta Metall Mater 32 (1995) 1489-1494
28. Allain S. Caractérisation et modélisation thermomécaniques multi-échelles des mécanismes de déformation et d'écrouissage d'aciers austénitiques a haute teneur en manganèse - Application a' l'effet TWIP. PhD thesis, INPL, Ecole des Mines de Nancy, France. 2002.
29. Allain S., Chateau J.P., Dahmoun D., and Bouaziz O. Modelling of mechanical twinning in high manganese content austenitic steel. Mater Sci Eng A 387-389 (2004) 272-276
30. Shiekhelsouk M.N., Favier V., Inal K., and Cherkaoui M. Modelling the behaviour of polycrystalline austenitic steel with twinning-induced plasticity effect. Int J Plasticity (2008) 10.1016/j.ijplas.2007.11.004
31. Nemat-Nasser S., and Guo W.G. Thermomechanical response of HSLA-65 steel plates: experiments and modelling. Mech Mater 37 (2005) 379-405
32. Guo W.G., and Nemat-Nasser S. Flow stress of Nitronic-50 stainless steel over a wide range of strain rates and temperatures. Mech Mater 38 (2006) 1090-1103
33. Fréchard S., Redjaïmia A., Lach E., and Lichtenberger A. Dynamical behaviour and microstructural evolution of a nitrogen-alloyed austenitic stainless steel. Mater Sci Eng A 480 (2008) 89-95
34. Rusinek A, Rodríguez-Martínez JA, Klepaczko JR, Pe{ogonek}cherski RB, Arias A. Modelling of thermo-visco-plastic behaviour of Dh-36 and Weldox-460-E structural steels at wide ranges of strain rates and temperatures, comparison of constitutive relations and application for impact problems. Mech Mater, submitted for publication.
35. Borvik T., Langseth M., Hopperstad O.S., and Malo K.A. Ballistic penetration of steel plates. Int J Impact Eng 22 (1999) 855-886
36. Borvik T., Langseth M., Hoperstad O.S., and Malo K.A. Perforation of 12 mm thick steel plates by 20 mm diameter projectiles with flat, hemispherical and conical noses Part I: experimental study. Int J Impact Eng 27 1 (2002) 19-35
37. Teng X., Wierzbicki T., Hiermaier S., and Rohr I. Numerical prediction of fracture in the Taylor test. Int J Solids Struct 42 29 (2005) 29-48
38. Arias A., Rodríguez-Martínez J.A., and Rusinek A. Numerical simulations of impact behaviour of thin steel to cylindrical, conical and hemispherical non-deformable projectiles. Eng Fract Mech 75 (2008) 1635-1656
39. Rusinek A., Rodríguez-Martínez J.A., Arias A., Klepaczko J.R., and López-Puente J. Influence of conical projectile diameter on perpendicular impact of thin steel plate. Eng Fract Mech 75 (2008) 2946-2967
40. Denhard E.E., and Espy R.H. Austenitic stainless with unusual mechanical and corrosion properties. Metals Eng Quart November (1972) 18-20
41. Ritter A.M., and Henry M.F. Phase transformations during aging of a nitrogen-strengthened austenitic stainless steel. Metall Trans A. 16A (1985) 1759-1771
42. Ritter A.M. Sigma-phase formation in Nitronic-50 and Nitronic-50W stainless steels. J Mater Sci 23 (1988) 3348-3356
43. Fréchard S., Redjaïmia A., Lach E., and Lichtenberger A. Mechanical behaviour of nitrogen-alloyed austenitic stainless steel hardened by warm rolling. Mater Sci Eng A 415 (2006) 219-224
44. Magness Jr. L.S. High strain rate deformation behaviors of kinetic energy penetrator materials during ballistic impact. Mech Mater 17 2-3 (1994) 47-154
45. Couque H., Lichtenberger A., Lach E., and Salesse B. Study of dynamic plastic deformation of a nitrogen alloyed steel using single and symmetric Taylor testing. J Phys IV France 10 (2000)
46. Abed F.H., George Z., and Voyiadjis G.Z. Plastic deformation modelling of AL-6XN stainless steel at low and high strain rates and temperatures using a combination of bcc and fcc mechanisms of metals. Int J Plasticity. 21 (2005) 1618-1639
47. Lewis A.C., Bingert J.F., Rowenhorst D.J., Gupta A., Geltmacher A.B., and Spanos G. Two- and three-dimensional microstructural characterization of a super-austenitic stainless steel. Mater Sci Eng A 418 (2006) 11-18
48. Brooks J.A., and Lippold J.C. Selection of wrought austenitic stainless steels. ASM handbook vol. 6 (1990), ASM International p. 457-69
49. Hecker S.S., Stout M.G., Staudhammer K.P., and Smith J.L. Effects of strain state and strain rate on deformation induced transformation in 304 stainless steel. I Magnetic measurements and mechanical behaviour. Metall Trans A 13A (1982) 619-626
50. Stout M.G., and Follansbee P.S. Strain rate sensitivity, strain hardening, and yield behaviour of 304L stainless steel. Trans ASME J Eng Mater Technol 108 (1986) 344-353
51. Ishikawa K., and Tanimura S. Strain rate sensitivity of low stress at low temperatures in 304 N stainless steel. Int J Plasticity 8 (1992) 947-958
52. Rusinek A., and Klepaczko J.R. Shear testing of sheet steel at wide range of strain rates and a constitutive relation with strain-rate and temperature dependence of the flow stress. Int J Plasticity 17 (2001) 87-115
53. Rusinek A., Zaera R., Klepaczko J.R., and Cheriguene R. Analysis of inertia and scale effects on dynamic neck formation during tension of sheet steel. Acta Mater 53 (2005) 5387-5400
54. Rusinek A., Zaera R., and Klepaczko J.R. Constitutive relations in 3-D for a wide range of strain rates and temperatures - application to mild steels. Int J Solids Struct 44 (2007) 5611-5634
55. Rusinek A., and Zaera R. Finite element simulation of steel ring fragmentation under radial expansion. Int J Impact Eng 34 (2007) 799-822
56. Rusinek A, Rodríguez-Martínez JA, Zaera R, Klepaczko JR, Arias A, Sauvelet C. Experimental and numerical analysis of failure process of mild steel sheets subjected to perpendicular impact by hemispherical projectiles. Int J Impact Eng, submitted for publication.
57. Klepaczko J.R. A general approach to rate sensitivity and constitutive modeling of FCC and BCC metals. Impact effects of fast transient loadings (1998), A.A. Balkema, Rotterdam 3-35
58. .
59. MacGregor C., and Fisher J.C. A velocity modified temperature for the plastic flow of metals. J Appl Mech 13 (1946) 11-16
60. Berbenni S., Favier V., Lemoine X., and Berveiller N. Micromechanical modelling of the elastic-viscoplastic behaviour of polycrystalline steels having different microstructures. Mater Sci Eng 372 (2004) 128-136
61. .
62. Rusinek A., and Klepaczko J.R. Experiments on heat generated during plastic deformation and stored energy for TRIP steels. Mater Design 30 (2009) 35-48
63. Johnson GR, Cook WH. A constitutive model and data for metals subjected to large strains, high strain rates and high temperatures. In: Proceedings of 7th international symposium on ballistics, 1983. p. 541-7.
64. Grässel O., Krüger L., Frommeyer G., and Meyer L.W. High strength Fe-Mn-(Al, Si) TRIP/TWIP steels development-properties-application. Int J Plasticity 16 (2000) 1391-1409