Crystal plasticity-based forming limit prediction for non-cubic metals: Application to Mg alloy AZ31B

International Journal of Plasticity

Volumn 25, Issue 3, 2009, Pages 379-398

  John Neil, C ^a   Agnew, Sean R ^a  

^a University of Virginia   (United States)

Author keywords

Forming limit diagram; Magnesium; Strain rate sensitivity; Texture; Warm forming

Indexed keywords

ALLOYS; DYNAMIC RECRYSTALLIZATION; FORMING; HARDENING; MAGNESIUM; MAGNESIUM PRINTING PLATES; METAL FORMING; PLASTICITY; SINGLE CRYSTALS; STRAIN HARDENING; TEXTURES; TWINNING;

CONSTITUTIVE PARAMETERS; CRYSTAL PLASTICITIES; CRYSTAL PLASTICITY MODELS; CRYSTALLO-GRAPHIC TEXTURES; CUBIC METALS; CURRENT MODELING; FAILURE MECHANISMS; FORMING LIMIT CURVES; FORMING LIMIT DIAGRAM; FORMING LIMITS; HARDENING BEHAVIORS; HARDENING RESPONSE; HEXAGONAL CLOSE PACKED; HIGHER TEMPERATURES; INDUCED ANISOTROPIES; MECHANICAL TWINNINGS; MG ALLOYS; PLASTIC RESPONSE; RECRYSTALLIZATION; STRAIN PATHS; STRAIN RATE SENSITIVITY; STRAIN-RATE HARDENINGS; TEMPERATURE DEPENDENT BEHAVIORS; TEXTURE; TEXTURE EVOLUTIONS; VISCOPLASTIC; WARM FORMING;

STRAIN RATE;

EID: 59649105253     PISSN: 07496419     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijplas.2008.05.003     Document Type: Article

References (70)

1. Agnew S.R., Dreyer C.E., Polesak III F.J., Chiu W.V., Neil C.J., and Rodriguez M. Constitutive behavior of four wrought magnesium alloys under warm forming conditions. In: Pekguleryuz M., Nyberg E., Beals R.B., and Neelameggham N. (Eds). Magnesium Technology (2008), TMS, Warrendale, PA 159-164
2. Agnew S.R., and Duygulu O. A mechanistic understanding of the formability of magnesium: examining the role of temperature on the deformation mechanisms. Mater. Sci. Forum 419-422 (2003) 177-188
3. Agnew S.R., and Duygulu O. Plastic anisotropy and the role of non-basal slip in magnesium alloy AZ31B. Int. J. Plast. 21 (2005) 1161-1193
4. Agnew S.R., Yoo M.H., and Tomé C.N. Application of texture simulation to understanding mechanical behavior of Mg and solid solution alloys containing Li or Y. Acta Mater. 49 (2001) 4277-4289
5. Asaro R.J., and Needleman A. Texture development and strain hardening in rate dependent polycrystals. Acta Metall. 33 (1985) 923-953
6. Ashby M.F. Overview no. 80: on the engineering properties of materials. Acta Metall. 37 (1989) 1273-1293
7. Barlat F., and Lian J. Plastic behavior and stretch ability of sheet metals. Part I: a yield function for orthotropic sheet under plane stress conditions. Int. J. Plast. 5 (1989) 51-66
8. Barlat F., Lege D.J., and Berm J.C. A six component yield function for anisotropic materials. Int. J. Plast. 7 (1991) 693-712
9. Barlat F., Becker R.C., Hayashida Y., Maeda Y., Yanagawa M., Chung K., Brem J.C., Lege D.J., Matsui K., Murtha S.J., and Hattori S. Yielding description for solution strengthened aluminum alloys. Int. J. Plast. 13 (1997) 385-401
10. Barlat F., Maeda Y., Chung K., et al. Yield function development for aluminum alloys sheets. J. Mech. Phys. Solid 11/12 (1997) 1727-1763
11. Barnett M.R. Influence of deformation conditions and texture on the high temperature flow stress of magnesium AZ31. J. Light Met. 1 (2001) 167-177
12. Barnett M.R. A Taylor model based description of the proof stress of magnesium AZ31 during hot working. Metall. Mater. Trans. A 34 (2003) 1799-1806
13. Barnett M.R. Twinning and the ductility of magnesium alloys. Part I: tension twins. Mater. Sci. Eng. A 464 (2007) 1-7
14. Basinski Z.S., Szczerba M.S., Niewczas M., Embury J.D., and Basinski S.J. The transformation of slip dislocations during twinning of copper-aluminum alloy crystals. Rev. Metall. 94 (1997) 1037-1043
15. Bohlen J., Nürnberg M.R., Senn J.W., Letzig D., and Agnew S.R. The texture and anisotropy of magnesium-zinc-rare earth alloy sheets. Acta Mater. 55 (2006) 2101-2112
16. Boyle K.P. Latent hardening in copper and copper alloys. Mater. Sci. Forum (2005) 1043-1048
17. Boyle, K.P., Essadiqui, E., Verma, R., 2006. Computational modeling of continuous dynamic recrystallization in magnesium. CANMET Report, MTL 2006-23, Natural Resources Canada, Ottawa, Ontario, December 2006, p. 12.
18. Brown D.W., Agnew S.R., Bourke M.A.M., Holden T.M., Vogel S.C., and Tomé C.N. Internal strain and texture evolution during deformation twinning in magnesium. Mater. Sci. Eng. A 399 (2005) 1-12
19. Cao J., Yao H., Karafillis A., and Boyce M. Prediction of localized thinning in sheet metal using a general anisotropic yield criterion. Int. J. Plast. 16 (2000) 1105-1129
20. Chino Y., Lee J.-S., Kensuke S., Kamiya A., and Mamoru M. Press formability of a rolled AZ31 Mg alloy sheet with controlled texture. Mater. Lett. 60 (2006) 173-176
21. Conrad H. Effect of strain-rate sensitivity of flow-stress on stretch formability of sheet metals. J. Mech. Work Technol. 2 (1978) 67-74
22. Conrad H., and Robertson W.D. Effect of temperature on the flow stress and strain-hardening coefficient of magnesium single crystals. Trans. TMS-AIME 209 (1957) 503-512
23. Couret A., and Caillard D. An in-situ study of prismatic glide in magnesium. Acta Metall. 33 (1985) 1447-1454
24. Dreyer, C.E., Wagoner, R.H., Agnew, S.R., 2008. Formability of a more randomly textured magnesium alloy sheet: application of an improved warm sheet formability test. J. Mater. Process. Tech. (submitted for publication).
25. Gharghouri M.A., Weatherly G.C., Embury J.D., and Root J. Study of the mechanical properties of Mg-7.7 at% Al by in situ neutron diffraction. Phil. Mag. 79 (1999) 1671-1695
26. Geiger M., Merklein M., and Hecht J. Warm hydroforming of magnesium sheets - results and microstructural changes. In: Bariani P.F. (Ed). Proceedings of the 8th International Conference on Technology of Plasticity (2005), Springer-Verlag, Berlin 51
27. Hecker, S.S., 1972. A simple forming limit curve technique and results on aluminum alloys, sheet metal forming and formability. In: Proceedings of the 7th Biennial Congress of the International Deep Drawing Research Group, Amsterdam, pp. 5.1-5.8.
28. Hecker S.S. Formability of aluminum alloy sheets. J. Eng. Mater. Tech. 97 (1975) 66-73
29. Hill R. A theory of the yielding and plastic flow of anisotropic metals. Proc. Royal Soc. Lond. A193 (1948) 281-297
30. Hill R. On discontinuous plastic states with special reference to localized necking in thin sheets. J. Mech. Phys. Solid 1 (1952) 19-30
31. Hill R. Theoretical plasticity of textured aggregates. Math. Proc. Camb. Philos. Soc. 85 (1979) 179-191
32. Hosford W.F. Generalized isotropic yield criterion. J. Appl. Mech. 19 (1972) 607-609
33. Hutchinson J.W., and Neale K.W. Sheet necking. II. Time independent behavior. III. Strain-rate effects. In: Koistinen K.P., and Wang N.-M. (Eds). Mechanics of Sheet Metal Forming 2002 (1978), Plenum, Ney York, NY 127-153 pp. 269-285
34. Inal, K., 2007. Personal communication.
35. Inal K., Neale K.W., and Aboutajeddine A. Forming limit comparisons for FCC and BCC sheets. Int. J. Plast. 21 (2004) 1255-1266
36. Jain A., and Agnew S.R. Modeling the temperature dependant effect of twinning on the behavior of magnesium alloy AZ31B sheet. Mater. Sci. Eng. A 462 (2007) 29-36
37. Kalidindi S.R. Incorporation of deformation twinning in crystal plasticity models. J. Mech. Phys. Solid 46 (1998) 267-290
38. Karafillis A.P., and Boyce M.C. A general anisotropic yield criterion using bounds and transformation weighting tensor. J. Mech. Phys. Solid 41 (1993) 1859-1886
39. Keeler, S.P., 1961. Plastic instability and fracture in sheets stretched over rigid punches. Ph.D Thesis, Massachusetts Institute of Technology, Cambridge, MA.
40. Kocks U.F., Argon A.S., and Ashby M.F. Thermodynamics and kinetics of slip. Prog. Mat. Sci. 19 (1975) 1-288
41. Kocks U.F., and Mecking H. Physics and phenomenology of strain hardening: the FCC case. Prog. Mat. Sci. 48 (2003)
42. Kok S., Beaudoin A.J., and Tortorelli D.A. A ploycrystal plasticity model based on the mechanical threshold. Int. J. Plast. 18 (2002) 715-741
43. Lebensohn R.A., and Tomé C.N. A self-consistent anisotropic approach. Acta Metall. 41 (1993) 2611-2624
44. Lee Y.S., Kim M.C., Kim S.W., Kwon Y.N., Choi S.W., and Lee J.H. Experimental and analytical studies for forming limit of AZ31 alloy on warm sheet metal forming. J. Mater. Process Tech. 187 (2007) 103-107
45. Ma A., and Roters F. A constitutive model for FCC single crystals based on dislocation densities and its application to uniaxial compression of aluminum single crystals. Acta Mater. 52 (2004) 3603-3612
46. Marciniak Z., and Kuczynski K. Limit strains in processes of stretch-forming sheet metal. Int. J. Mech. Sci. 9 (1967) 609-620
47. Marciniak Z., Kuczynski K., and Pokora T. Influence of the plastic properties of a material on the forming limit diagram for sheet metal in tension. Int. J. Mech. Sci. 15 (1973) 789-805
48. Molinari A., and Tóth L.S. Tuning a self consistent viscoplastic model by finite element results - I. Model. Acta Metall. 42 (1994) 2453-2458
49. Nakazima, K., Kikuma, T., Hasuka, K., 1968. Study on the formability of steel sheets. Yawata Tech. Report No. 264, pp. 140-141.
50. Nemat-Nasser S., Okinaka T., and Ni L. A physically-based constitutive model for bcc crystals with application to polycrystalline tantalum. J. Mech. Phys. Solid 46 (1998) 1009-1038
51. Otsuka K. Shape Memory Materials (1998), Cambridge University Press, New York pp. 59-62
52. Reed-Hill R.E., and Robertson W.E. Deformation of magnesium single crystals by non-basal slip. Trans. AIME 209 (1957) 496-502
53. Reed-Hill R.E., and Robertson W.D. Pyramidal slip in magnesium. Trans. TMS-AIME 221 (1958) 256-259
54. Sajuri B.Z., Miyashita Y., Hosokai Y., and Mutoh Y. Effect of MN content and texture on fatigue properties of as-cast and extruded AZ61 magnesium alloys. Int. J. Mech. Sci. 48 (2006) 198-209
55. Sellars C.M., and Tegart W.J. Relationship between strength and structure in deformation at elevated temperatures. Mem. Sci. Rev. Metall. 63 (1966) 731-745
56. Senn, J.W., 2007. M.S. Thesis, University of Virginia.
57. Shahi, M., Nemes, J.A., 2006. Crystal plasticity modeling of the slip systems activity in Mg alloys at higher temperatures. SAE Int. Technical Paper 2007-01-1030.
58. Stohr J.F., and Poirier J.P. Etude en microscopie electronique de glissement pyramidal {11-22}〈11-23〉 dans le magnesium. Phil. Mag. 25 (1972) 1313-1329
59. Takuda H., Fujimoto H., and Hatta N. Modelling on flow stress of Mg-Al-Zn alloys at elevated temperatures. J. Mater. Process. Tech. 80-81 (1998) 513-516
60. Tomé C.N., Lebensohn R.A., and Kocks U.F. A model for texture development dominated by deformation twinning - application to zirconium alloys. Acta Metall. Mater. 39 (1991) 2667-2680
61. Tomé, C.N., 2007. Personal communication.
62. Toth L.S., Dudzinski D., and Molinari A. Forming limit predictions with the perturbation method using stress potential functions of polycrystal viscoplasticity. Int. J. Mech. Sci. 38 (1996) 805-824
63. Toth L.S., Hirsch J., and Van Houtte P. On the role of texture development in the forming limits of sheet metals. Int. J. Mech. Sci. 38 (1996) 1117-1126
64. Vagarali S.S., and Langdon T.G. Deformation mechanisms in hcp metals at elevated temperatures - II. Creep behavior of a Ag-0.8% Al solid solution alloy. Acta Metall. 30 (1982) 1157-1170
65. Veerman C.C., Hartman L., Peels J.J., and Neve R.F. Determination of appearing and admissible strains in cold-reduced sheets. Sheet Metal Ind. 48 (1971) 678-680
66. Wagoner R.H., Wang W., and Sriram S. Development of OSU formability test and OSU friction test. J. Mater. Process. Tech. 45 (1994) 13-18
67. Ward Flynn P., Mote J., and Dorn J.E. On the thermally activated mechanism of prismatic slip in magnesium single crystals. Trans. TMS-AIME 221 (1961) 1148-1154
68. Wu P.D., Neale K.W., and Van der Giessen E. On crystal plasticity FLD analysis. Proc. Royal Soc. Lond. A 453 (1997) 1831-1848
69. Yukutake E., Kaneko J., and Sugamata M. Anisotropy and non-uniformity in plastic behavior of AZ31 magnesium alloy plates. Mater. Trans. 44 (2003) 452-457
70. Zhou Y., and Neale K.W. Predictions of forming limit diagrams using a rate-sensitive crystal plasticity model. Int. J. Mech. Sci. 37 (1995) 1-20