Hard machining of hardened bearing steel using cubic boron nitride tool

Journal of Materials Processing Technology

Volumn 209, Issue 2, 2009, Pages 1092-1104

  Yallese, Mohamed Athmane ^a   Chaoui, Kamel ^b   Zeghib, Nassereddine ^b   Boulanouar, Lakhdar ^b   Rigal, Jean François ^c  

^a UNIVERSITY OF GUELMA   (Algeria)

^b BADJI MOKHTAR UNIVERSITY   (Algeria)

^c UNIVERSITÉ DE LYON   (France)

Author keywords

Cubic boron nitride; Cutting forces; Hard turning; Hardened steel; Roughness; Wear

Indexed keywords

CERAMIC TOOLS; CHROMIUM ALLOYS; CUBIC BORON NITRIDE; CUTTING; HARDENING; III-V SEMICONDUCTORS; SURFACE ROUGHNESS; TURNING; WEAR OF MATERIALS; WEAR RESISTANCE;

CONTROLLING PARAMETERS; CUBIC BORON NITRIDE TOOL; CUTTING FORCES; EXPERIMENTAL INVESTIGATIONS; HARD TURNING; HARDENED BEARING STEELS; HARDENED STEEL; PARAMETRIC -ANALYSIS;

CUTTING TOOLS;

EID: 58149162000     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmatprotec.2008.03.014     Document Type: Article

References (16)

1. Arunachalam R.M., Mannan M.A., and Spowage A.C. Residual stress and surface roughness when facing age hardened Inconel 718 with CBN and ceramic cutting tools. Int. J. Mach. Tool. Manuf. 44 (2004) 879-887
2. Banga G.C., and Abrão A.M. Turning of hardened 100Cr6 bearing steel with ceramic and PCBN cutting tools. J. Mater. Process. Technol. 143-144 (2003) 237-241
3. Chou Y.K., Chris C.J., and Barash M.M. Experimental investigation on CBN turning of hardened AISI 52100 steel. J. Mater. Process. Technol. 124 (2002) 274-283
4. Chou Y.K. Hard turning of M50 steel with different microstructures in continuous and intermittent cutting. Wear 225 (2003) 1388-1394
5. Huang Y., Chou Y.K., and Liang Y.S. CBN tool wear in hard turning: a survey on research progresses. Int. J. Adv. Manuf. Technol. 35 (2006) 443-453
6. Kitagawa T., Kubo A., and Maekawa K. Temperature and wear of cutting tools in high speed machining of Inconel 718 and Ti-6Al-6V-2Sn. Wear 202 (1997) 142-148
7. Lahiff C., Gordon S., and Phelan P. PCBN tool wear modes and mechanisms in finish hard turning. Robot. Comput. Integr. Manuf. 23 (2007) 638-644
8. Lima J.G., Avila R.F., Abrão A.M., Faustino M., and Paulo Davim J. Hard turning: AISI 4340 high strength low alloy steel and AISI D2 cold work tool steel. J. Mater. Process. Technol. 169 (2005) 388-395
9. Luo S.Y., Liao Y.S., and Tsai Y.Y. Wear characteristics in turning high hardness alloy steel by ceramic and CBN tools. J. Mater. Process. Technol. 88 (1999) 114-121
10. Nabahani F. Wear mechanisms of ultra-hardware cutting tools materials. J. Mater. Process. Technol. 115 (2001) 402-412
11. O'Sullivan D., and Cottrell M. Temperature measurement in single point turning. J. Mater. Process. Technol. 118 (2001) 301-308
12. Poulachon G., Bandyopadhyay B.P., Jawahir I.S., Pheulpin S., and Seguin E. The influence of microstructure of hardened tool steel workpiece on the wear of PCBN cutting tools. Int. J. Mach. Tool. Manuf. 43 (2003) 139-144
13. Remadna M., and Rigal J.-F. Evolution during time of tool wear and cutting force in the case of hard turning with CBN inserts. J. Mater. Process. Technol. 178 (2006) 67-75
14. Thiele J.D., and Melkote S.N. Effect of cutting edge geometry and workpiece hardness on surface generation in the finish hard turning of AISI 52100 steel. J. Mater. Process. Technol. 94 (1999) 216-226
15. Yallese M.A., Rigal J.-F., Chaoui K., and Boulanouar L. The effects of cutting conditions on mixed ceramic and cubic boron nitride tool and on surface roughness during machining of X200Cr12 steel (60 HRC). Proc. I Mech. E 219 Part B (2005) 35-55
16. Yallese, M.A., 2005. Wear behaviour of modern cutting tool materials under hard turning conditions. PhD Thesis. Badji Mokhtar University, Annaba, Algeria.